Buy 104640-0450 ZEXEL 9 461 615 178 BOSCH FUEL-INJECTION PUMP 9461615178 1046400450


 

Information fuel-injection pump

BOSCH 9 461 615 178 9461615178
ZEXEL 104640-0450 1046400450
104640-0450 FUEL-INJECTION PUMP
Rating:
44
Buy FUEL-INJECTION PUMP 104640-0450 zexel genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
 

16 Apr 2018
1200 Hundredths Pounds
Generic: Generic
NEW ZEXEL 104740-0450 INJECTION PUMP 1046400450
 

01 Feb 2018
1181 Hundredths Pounds
Generic: Generic
NEW ZEXEL 104640-0450 FUEL INJECTION PUMP 1046400450
 

15 Mar 2018
1200 Hundredths Pounds
Generic: Generic
NEW ZEXEL 104640-0450 INJECTION PUMP 1046400450

Include in #2:

104740-0450 as FUEL INJECTION PUMP

Cross reference number

Zexel num
Bosch num
Firm num
Name
104640-0450 
104640-0451 
9 461 615 178 
   
FUEL-INJECTION PUMP
* Q




Information:


Parts Required For 4C-8180 Timing Tool Group
Refer to Chart A for item identification.Assemble and Set the 4C-8180 Timing Tool Group
1. Obtain a 108-2104 Plunger and Barrel Assembly. This part can be new or used. If the part is used, make sure it is in good working condition. The plunger should move freely in the barrel.
4C-8181 Timing Tool Assembly
(9) 8J-3819 Spring. (10) 1N-3257 Retainer Ring. (11) Plunger and barrel from 108-2104 Plunger and Barrel Assembly. (12) 4C-8178 Indicator Mount Bonnet. (14) 4C-8179 Bonnet Nut. (16) 2W-3429 Gear Segment (part of 108-2104). (17) 8N-0669 Bolt (part of 108-2104). (18) 4P-8704 Spring (part of 108-2104). (19) 9Y-2088 Washer.2. Make a 4C-8181 Timing Tool Assembly out of the 108-2104 Plunger and Barrel Assembly. The 4C-8181 Timing Tool Assembly is not a serviceable part. a. Remove and discard 8N-0669 Bolt (17), 2W-3429 Gear Segment (16), and 4P-8704 Spring (18) from the 108-2104 Plunger and Barrel Assembly.b. Assemble 8J-3819 Spring (9) and 9Y-2088 Washer (19) onto plunger. The 9Y-2088 Washer is part of the 108-2104 Plunger and Barrel Assembly.c. Install the 4C-8178 Indicator Mount Bonnet (12) onto the barrel using a 1N-3257 Retainer Ring (10).d. Slip 4C-8179 Bonnet Nut (14) over indicator mount bonnet (12).e. This tool is now a 4C-8181 Timing Tool Assembly (11).3. Assemble knurled gauge collar (3) onto gauge (5) by threading them together. Hand tighten the two parts. Make sure the gauging surfaces are clean and free of all debris, nicks, etc.4. Install 4C-8181 Timing Tool Assembly (11) into gauge collar (3).5. Thread bonnet nut (14) into gauge collar (3) and hand tighten with 9U-5120 Spanner Wrench (13). This will secure timing tool assembly (11) into gauge collar (3).6. Spring (9) on the timing tool assembly should make the end of the plunger extend approximately 30 mm (1.2 in) past the end of gauge (5).7. Push on the end of the plunger and make sure it travels freely (under spring force) in and out of the gauge block bore. If there is binding, disassemble and correct the problem.8. Install either a 5P-4814 Collet (6) or 4C-2982 Collet Assembly (7) into indicator mount bonnet (12).9. Install an indicator with a 5P-7262 Contact Point into collet (6 or 7). Use either a 6V-6106 Dial Indicator or an 8T-1002 Probe connected to an 8T-1001 Electronic Position Indicator.
Do not over tighten collet (6 or 7) holding the indicator. Over-tightening can result in damage to the indicator or the electronic position indicator probe.
10. Tighten collet (6 or 7) just enough to make sure the indicator or electronic position indicator probe will not move in collet.11. Zero the indicator by following this procedure. a. Place the 4C-8183 Gauge Plate (8) onto a flat surface.b. Carefully hold the entire 4C-8180 Timing Tool Group and place it on the gauge plate, with the end of the plunger contacting the plate.c. Push down on the entire assembly, compressing the spring, until the bottom of gauge (5) is in complete contact with gauge plate (8).
Zero The Timing Tool Assembly With

Have questions with 104640-0450?





Group cross 104640-0450 ZEXEL

9 461 621 666 
 
FUEL-INJECTION PUMP
9 461 621 667 
 
FUEL-INJECTION PUMP
9 461 628 103 
 
FUEL-INJECTION PUMP
9 461 621 668 
 
FUEL-INJECTION PUMP
9 461 621 669 
 
FUEL-INJECTION PUMP
9 461 621 670 
 
FUEL-INJECTION PUMP
F 01G 29X 002 
 
FUEL-INJECTION PUMP
9 461 621 671 
 
FUEL-INJECTION PUMP
9 461 621 672 
 
FUEL-INJECTION PUMP
9 461 621 673 
 
FUEL-INJECTION PUMP
9 461 621 674 
 
FUEL-INJECTION PUMP
9 461 621 675 
 
FUEL-INJECTION PUMP
9 461 618 328 
NP-VE4/10F1900RNP841 
 
FUEL-INJECTION PUMP
9 461 621 676 
 
FUEL-INJECTION PUMP
9 461 618 063 
 
FUEL-INJECTION PUMP
104640-0450  

104640-0451 
9 461 615 178 
 
FUEL-INJECTION PUMP
9 461 621 677 
 
FUEL-INJECTION PUMP
9 461 616 676 
NP-VE4/10F1000RNP909 
 
FUEL-INJECTION PUMP
9 461 621 678 
 
FUEL-INJECTION PUMP
9 461 621 679 
 
FUEL-INJECTION PUMP
9 461 621 680 
 
FUEL-INJECTION PUMP
9 461 621 681 
 
FUEL-INJECTION PUMP
9 461 621 682 
 
FUEL-INJECTION PUMP
9 461 620 485 
NP-VE4/10F1900RNP955 
 
FUEL-INJECTION PUMP
Back to top