104293-3060 ZEXEL 9 410 617 754 BOSCH FUEL-INJECTION PUMP 9410617754 1042933060 3531016320c

Information fuel-injection pump

BOSCH 9 410 617 754 9410617754

ZEXEL 104293-3060 1042933060

KAWASAKI-HEAVY 3531016320C 3531016320c

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy FUEL-INJECTION PUMP 104293-3060 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104293-3060
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY
8.	Nozzle and Holder
9.	Open Pre:MPa(Kqf/cm2)
10.	NOZZLE-HOLDER
11.	NOZZLE

Scheme ###:

5.	[3]	140153-2520	PLUNGER-AND-BARREL ASSY
12.	[3]	140110-3720	DELIVERY-VALVE ASSEMBLY
13.	[3]	140112-3000	COMPRESSION SPRING
16.	[3]	140115-1400	GASKET
17.	[3]	140116-6100	FITTING
20.	[3]	016500-1520	O-RING
40.	[3]	140200-1620	TAPPET
44.	[3]	140212-0300	BEARING PIN
45.	[1]	140213-0500	WIRE
50.	[3]	140215-1900	COMPRESSION SPRING
51.	[3]	140216-0800	SLOTTED WASHER
52.	[3]	140217-2200	SLOTTED WASHER
53/1.	[1]	140217-5000	PLATE D19T2.60
53/1.	[1]	140217-5100	PLATE D19T2.65
53/1.	[1]	140217-5200	PLATE D19T2.70
53/1.	[1]	140217-5300	PLATE D19T2.75
53/1.	[1]	140217-5400	PLATE D19T2.80
53/1.	[1]	140217-5500	PLATE D19T2.85
53/1.	[1]	140217-5600	PLATE D19T2.90
53/1.	[1]	140217-5700	PLATE D19T2.95
53/1.	[1]	140217-5800	PLATE D19T3.00
53/1.	[1]	140217-5900	PLATE D19T3.05
53/1.	[1]	140217-6000	PLATE D19T3.10
53/1.	[1]	140217-6100	PLATE D19T3.15
53/1.	[1]	140217-6200	PLATE D19T3.20
53/1.	[1]	140217-6300	PLATE D19T3.25
53/1.	[1]	140217-6400	PLATE D19T3.30
53/1.	[1]	140217-6500	PLATE D19T3.35
53/1.	[1]	140217-6600	PLATE D19T3.40
53/1.	[1]	140217-6700	PLATE D19T3.45
53/1.	[1]	140217-6800	PLATE D19T3.50
53/1.	[1]	140217-6900	PLATE D19T3.55
53/1.	[1]	140217-7000	PLATE D19T3.60
53/1.	[1]	140217-7100	PLATE D19T3.65
53/1.	[1]	140217-7200	PLATE D19T3.70
53/1.	[1]	140217-7300	PLATE D19T3.75
53/1.	[1]	140217-7400	PLATE D19T3.80
53/1.	[1]	140217-7500	PLATE D19T3.85
53/1.	[1]	140217-7600	PLATE D19T3.90
53/1.	[1]	140217-7700	PLATE D19T3.95
53/1.	[1]	140217-7800	PLATE D19T4.00
53/1.	[1]	140217-7900	PLATE D19T4.05
53/1.	[1]	140217-8000	PLATE D19T4.10
53/1.	[1]	140253-2000	PLATE
53/1.	[1]	140253-2100	PLATE
53/1.	[1]	140253-2200	PLATE
53/1.	[1]	140253-2300	PLATE
53/1.	[1]	140253-2400	PLATE
53/1.	[1]	140253-2500	PLATE
53/1.	[1]	140253-2600	PLATE
53/1.	[1]	140253-2700	PLATE
53/1.	[1]	140253-2800	PLATE
53/1.	[1]	140253-2900	PLATE
53/1.	[1]	140253-3000	PLATE
53/1.	[1]	140253-3100	PLATE
53/1.	[1]	140253-3200	PLATE
53/1.	[1]	140253-3300	PLATE
53/1.	[1]	140253-3400	PLATE
53/1.	[1]	140253-3500	PLATE
53/1.	[1]	140253-3600	PLATE
53/1.	[1]	140253-3700	PLATE
53/1.	[1]	140253-3800	PLATE
53/1.	[1]	140253-3900	PLATE
53/1.	[1]	140253-4000	PLATE
53/1.	[1]	140253-4100	PLATE
53/1.	[1]	140253-4200	PLATE
53/1.	[1]	140253-4300	PLATE
53/1.	[1]	140253-4400	PLATE
53/1.	[1]	140253-4500	PLATE
53/1.	[1]	140253-4600	PLATE
53/1.	[1]	140253-4700	PLATE
53/1.	[1]	140253-4800	PLATE
53/1.	[1]	140253-4900	PLATE
60.	[1]	140243-0320	CONTROL RACK
77.	[3]	140241-2700	CONTROL SLEEVE
92.	[1]	029711-2050	INLET UNION
93.	[1]	140402-1300	EYE BOLT
94.	[2]	026512-1540	GASKET D15.4&12.2T1.50
110.	[1]	140420-2300	BLEEDER SCREW
111.	[1]	026508-1240	GASKET D11.9&8.2T1
156.	[2]	140255-0000	BEARING PIN
157.	[2]	029320-6010	LOCKING WASHER
158.	[1]	140256-0400	COVER
159.	[2]	010735-1020	FLAT-HEAD SCREW M5P0.9L10

Include in #2:

104293-3060 as INJECTION-PUMP ASSEMBLY

104740-0980 as _

Cross reference number

Zexel num

Bosch num

Firm num

Name

104293-3060

9 410 617 754
NP-PFR3KD50/1NP5

3531016320C KAWASAKI-HEAVY

FUEL-INJECTION PUMP
K

104293-3060

9 410 617 754
NP-PFR3KD50/1NP5

490412052D KAWASAKI-HEAVY

FUEL-INJECTION PUMP
A K

Information:

Setting rack(4) Setting governor (setting maximum speed )(a) While applying the full load to the engine, hold the speed control lever in the specified maximum speed position.(b) Adjust the governor setting bolt (maximum speed setting bolt) to the specified speed position, and set it there.
Setting governor(5) Setting torque spring (optional specification)Set the speed control lever at the maximum speed, and apply the load to the engine. Turn the torque spring adjusting screw until the engine delivers the specified output at the specified speed. Fix the screw with the locknut, and install a cap to the lock nut.
Setting torque spring(6) Measuring speed variationMeasurement of speed variation at removal of load.(a) Operate the speed control to set the engine at the rated output and speed.(b) From this condition, instantaneously remove the load to put the engine into the no-load condition. Operate the engine with the speed control lever fixed.(c) The engine speed temporarily jumps up then lowers and stabilizes. Record the momentary maximum speed, stabilized speed, and time from the removal of the load to the stabilization of the speed.Measurement of speed variation at application of load.From the no-load condition, instantaneously apply the specified load to the engine. Record the momentary maximum speed, stabilized speed, and time from the application of the load to the stabilization of the speed.Calculation of speed variationCalculate the speed variation from the measured results. When the speed variation falls outside specified limits, adjust the governor notches.
Measuring speed variation(7) Adjusting speed variation (adjusting governor notches)(a) Adjust the speed variation by turning the adjusting screw of the swivel lever.(b) Remove the plug at the top of the governor, and set the speed control lever to the low idle speed position. The swivel lever turns up to reveal the head of the adjusting screw. Turn the adjusting screw with a flat-head screwdriver.(c) The speed variation decreases as the adjusting screw is tightened and increases as the adjusting screw is loosened. One notch equals a quarter turn of the adjusting screw and changes the engine speed by three to five revolutions.(d) Turning the adjusting screw changes the governor spring tension and hence the maximum speed. Readjust the governor setting bolt.(e) The maximum speed increases as the adjusting screw is tightened and decreases as the adjusting screw is loosened.
The adjusting screw can be loosened by 20 notches (or five turns) from the position where it is fully tightened. It is dangerous if the adjusting screw is loosened more.
Adjusting speed variation(8) SealingSeal each setting bolt.Break-in Operation
When the engine is overhauled, it should be mounted on a dynamometer and operated for break-in and inspection.Starting Up
(1) Before starting the engine, check the levels of coolant, engine oil and fuel, and bleed the fuel and cooling system.(2) With the fuel supply cut off, operate the starter and crank the engine for about 15 seconds to circulate engine oil.(3) Move the speed control lever slightly in the direction for increased fuel (do not move it to "full injection" position), and then turn the starter switch