104293-2050 ZEXEL 9 410 617 749 BOSCH FUEL-INJECTION PUMP 9410617749 1042932050

Information fuel-injection pump

BOSCH 9 410 617 749 9410617749

ZEXEL 104293-2050 1042932050

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy FUEL-INJECTION PUMP 104293-2050 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104293-2050
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY	105141-2370
8.	Nozzle and Holder
9.	Open Pre:MPa(Kqf/cm2)	13.7{140}
10.	NOZZLE-HOLDER	105071-1421
11.	NOZZLE	105000-1600

Scheme ###:

5.	[2]	140153-2520	PLUNGER-AND-BARREL ASSY
12.	[2]	140110-3720	DELIVERY-VALVE ASSEMBLY
13.	[2]	140112-1700	COMPRESSION SPRING
16.	[2]	140115-1400	GASKET
17.	[2]	140116-6100	FITTING
20.	[2]	016500-1520	O-RING
40.	[2]	140200-1520	TAPPET
44.	[2]	140212-0300	BEARING PIN
45.	[1]	140213-0400	WIRE
50.	[2]	140215-0100	COMPRESSION SPRING
51.	[2]	140216-0700	SLOTTED WASHER
52.	[2]	140217-9100	SLOTTED WASHER
53/1.	[1]	140217-4400	SHIM D18.5&13T0.20
53/1.	[1]	140217-4500	SHIM D18.5&13T0.25
53/1.	[1]	140217-4600	SHIM D18.5&13T0.30
53/1.	[1]	140217-4700	SHIM D18.5&13T0.35
53/1.	[1]	140217-4800	SHIM D18.5&13T0.40
53/1.	[1]	140217-4900	SHIM D18.5&13T0.45
53/1.	[1]	140217-9500	SHIM D18.5&13T0.50
53/1.	[1]	140217-9600	SHIM D18.5&13T0.55
53/1.	[1]	140217-9700	SHIM D18.5&13T0.60
53/1.	[1]	140217-9800	SHIM D18.5&13T0.65
53/1.	[1]	140217-9900	SHIM D18.5&13T0.70
53/1.	[1]	140254-0400	SHIM D18.5&13.0T0.75
53/1.	[1]	140254-0500	SHIM D18.5&13.0T0.80
53/1.	[1]	140254-0600	SHIM D18.5&13.0T0.85
53/1.	[1]	140254-0700	SHIM D18.5&13.0T0.90
53/1.	[1]	140254-0800	SHIM D18.5&13.0T0.95
53/1.	[1]	140254-0900	SHIM D18.5&13.0T1.00
60.	[1]	140243-0220	CONTROL RACK
77.	[2]	140241-2700	CONTROL SLEEVE
92.	[1]	029711-2050	INLET UNION
93.	[1]	140402-1300	EYE BOLT
94.	[2]	026512-1540	GASKET D15.4&12.2T1.50
110.	[1]	140420-2300	BLEEDER SCREW
111.	[1]	026508-1240	GASKET D11.9&8.2T1
156.	[1]	140255-0000	BEARING PIN
157.	[1]	029320-6010	LOCKING WASHER
158.	[1]	140256-0300	COVER
159.	[1]	012255-1020	FLAT-HEAD SCREW

Include in #2:

104293-2050 as INJECTION-PUMP ASSEMBLY

104740-0800 as _

104740-0802

Cross reference number

Zexel num

Bosch num

Firm num

Name

104293-2050

9 410 617 749

FUEL-INJECTION PUMP
* K

Information:

Disassembly and Reassembly of General Parts
Oil seals
When installing oil seals, observe the following.Installation of Oil Seals to Housings
(a) Check the seal lip for scratches and damage, and be sure to position the lip correctly.(b) Apply a small amount of grease to the periphery (housing contact surface) of the oil seal before installation.(c) Use an oil seal driver that guides the seal lip and presses the seal periphery, as shown in the diagram on the right. Striking the oil seal directly with a hammer causes seal damage and results in oil leaks.
Oil seal driverInstallation of Oil Seals to Shafts
(a) Apply grease to the oil seal lip.(b) Use an oil seal guide similar to the one shown in the diagram when installing an oil seal over the stepped portion, splines, threads or key grooves.
Oil seal guideO-rings
Use an O-ring guide similar to the one shown in the diagram when installing an O-ring over the stepped portion, splines, threads or key grooves. Be sure to apply a small amount of grease to the O-ring before installation.
O-ring guideBearings
(1) When installing a bearing, be sure to push the inner or outer race that fits into the installation position. (When the inner race fits into the installation position, push the inner race into position. When the outer race fits into the installation position, push the outer race into position.) Be sure to use a bearing driver similar to the one shown in the diagram.
Bearing driver(2) Use of a press minimizes the impact on the bearing and ensures proper installation.
Using press for bearing installationLock Plates
Be sure to bend lock plates. The diagram on the right shows the methods of bending representative lock plates.
Bending lock plateSplit Pins and Spring Pins
Generally, new split pins should be installed whenever split pins are removed. Be sure to bend split pins. Be sure to check spring pins for secure installation.