Information fuel-injection pump
BOSCH
9 410 618 035
9410618035
ZEXEL
104276-5120
1042765120
Rating:
Components :
| 0. | INJECTION-PUMP ASSEMBLY | 104276-5120 |
| 1. | _ | |
| 2. | FUEL INJECTION PUMP | |
| 3. | NUMBER PLATE | |
| 4. | _ | |
| 5. | CAPSULE | |
| 6. | ADJUSTING DEVICE | |
| 7. | NOZZLE AND HOLDER ASSY | |
| 8. | Nozzle and Holder | |
| 9. | Open Pre:MPa(Kqf/cm2) | |
| 10. | NOZZLE-HOLDER | |
| 11. | NOZZLE |
Scheme ###:
| 1. | [1] | 141054-5923 | PUMP HOUSING |
| 5. | [1] | 141176-9021 | PLUNGER-AND-BARREL ASSY |
| 12. | [1] | 141145-0922 | DELIVERY-VALVE ASSEMBLY |
| 12/1. | [1] | 141141-9000 | SEAT;D.V. |
| 12/2. | [1] | 141138-1400 | FITTING |
| 12/3. | [1] | 141142-7300 | VALVE BODY |
| 12/4. | [1] | 141144-0300 | COMPRESSION SPRING |
| 12/5. | [1] | 141113-3400 | SLOTTED WASHER |
| 12/7. | [1] | 141113-3100 | SLOTTED WASHER |
| 12/8. | [1] | 141112-8701 | COILED SPRING |
| 12/9. | [1] | 141145-8400 | VALVE BODY |
| 12/10. | [2] | 141213-1100 | BEARING PIN |
| 19. | [1] | 016421-0600 | BACKUP RING |
| 20. | [1] | 141482-8600 | O-RING |
| 22. | [4] | 141124-4700 | BLEEDER SCREW |
| 25. | [2] | 141403-0001 | O-RING |
| 50. | [1] | 141215-5501 | COMPRESSION SPRING |
| 51. | [1] | 141216-1200 | SLOTTED WASHER |
| 52. | [1] | 141217-8400 | SLOTTED WASHER |
| 53. | [1] | 141294-0002 | GUIDE |
| 55. | [1] | 141220-0700 | LOCKING WASHER |
| 60. | [1] | 141291-2800 | CONTROL RACK |
| 77. | [1] | 141292-2600 | CONTROL SLEEVE |
| 81. | [1] | 141245-2000 | POINTER |
| 82/1. | [0] | 023500-6210 | PLAIN WASHER D11&6.4T1.5 |
| 82/1. | [0] | 029300-6010 | PLAIN WASHER D11&6.4T0.8 |
| 82/1. | [0] | 029300-6020 | PLAIN WASHER D11&6.4T0.35 |
| 83. | [1] | 020006-1440 | BLEEDER SCREW M6P1L14 |
| 90. | [1] | 029112-2020 | CAPSULE |
| 91. | [1] | 026522-2740 | GASKET D26.9&22.2T1 |
| 93. | [2] | 141402-3420 | EYE BOLT |
| 93. | [2] | 141402-3420 | EYE BOLT |
| 110. | [1] | 141420-1500 | BLEEDER SCREW |
| 111. | [1] | 141107-0500 | GASKET |
| 160. | [1] | 141418-1500 | SET OF NUTS |
| 161. | [1] | 141107-0700 | GASKET |
| 163. | [2] | 010110-1420 | BLEEDER SCREW |
| 163. | [2] | 010110-1420 | BLEEDER SCREW |
| 164. | [2] | 141107-0500 | GASKET |
| 164. | [2] | 141107-0500 | GASKET |
Include in #1:
101401-9247
as _
Include in #2:
104276-5120
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
There have been some instances of issues with the following fuel injection pumps:
Table 1
Part Number Description
295-0435 Fuel Injection Pump Gp
348-6930 Pump
415-4313 Pump
420-4524 Fuel Injection Pump
422-5257 Fuel Injection Pump
443-3226 Fuel Injection Pump The issue may be reported as low engine power or the high idle speed may be inconsistent. Most issues have been reported below 200–300 hours of service.Solution
Note: Do not attempt to adjust the fuel pump or repair the fuel pump.Install a replacement fuel pump of the same part number. Refer to Disassembly and Assembly, Fuel Injection Pump - Remove and Disassembly and Assembly, Fuel Injection Pump - Install for the correct procedure.Retain the removed fuel pump for 30 days. The fuel pump will be requested for return using the Send It Back (SIB) process.
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
There have been some instances of issues with the following fuel injection pumps:
Table 1
Part Number Description
295-0435 Fuel Injection Pump Gp
348-6930 Pump
415-4313 Pump
420-4524 Fuel Injection Pump
422-5257 Fuel Injection Pump
443-3226 Fuel Injection Pump The issue may be reported as low engine power or the high idle speed may be inconsistent. Most issues have been reported below 200–300 hours of service.Solution
Note: Do not attempt to adjust the fuel pump or repair the fuel pump.Install a replacement fuel pump of the same part number. Refer to Disassembly and Assembly, Fuel Injection Pump - Remove and Disassembly and Assembly, Fuel Injection Pump - Install for the correct procedure.Retain the removed fuel pump for 30 days. The fuel pump will be requested for return using the Send It Back (SIB) process.