Information fuel-injection pump
BOSCH
9 410 618 266
9410618266
ZEXEL
104265-3004
1042653004
DAIHATSU
E266480040ZB
e266480040zb

Rating:
Components :
0. | INJECTION-PUMP ASSEMBLY | 104265-3004 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | |
10. | NOZZLE-HOLDER | |
11. | NOZZLE |
Scheme ###:
1. | [1] | 141055-6800 | PUMP HOUSING |
5. | [1] | 141189-5022 | PLUNGER-AND-BARREL ASSY |
7. | [2] | 141133-9200 | CAPSULE |
7. | [2] | 141133-9200 | CAPSULE |
8. | [2] | 141485-1302 | O-RING |
8. | [2] | 141485-1302 | O-RING |
12. | [1] | 141145-6521 | DELIVERY-VALVE ASSEMBLY |
12/1. | [1] | 141146-2300 | SEAT;D.V. |
12/2. | [1] | 141138-1800 | FITTING |
12/3. | [1] | 141142-9100 | VALVE BODY |
12/4. | [1] | 141144-0500 | COMPRESSION SPRING |
12/5. | [1] | 141113-3201 | SLOTTED WASHER |
12/6. | [1] | 141145-8400 | VALVE BODY |
12/7. | [1] | 141112-8701 | COILED SPRING |
12/8. | [1] | 141113-2003 | FILLER PIECE |
12/9. | [2] | 010235-2520 | HEX-SOCKET-HEAD CAP SCREW |
16. | [1] | 150508-3100 | BEARING PIN |
18. | [8] | 141124-5900 | HEX-SOCKET-HEAD CAP SCREW |
21. | [1] | 141119-4901 | FLANGE BUSHING |
22. | [8] | 141124-6000 | BLEEDER SCREW |
24. | [2] | 016421-0600 | BACKUP RING |
25. | [3] | 141485-1002 | O-RING |
40. | [1] | 141200-3720 | TAPPET |
44. | [1] | 141212-0300 | BEARING PIN |
50. | [1] | 141215-9000 | COMPRESSION SPRING |
51. | [1] | 141216-7120 | SLOTTED WASHER |
52. | [1] | 141254-3600 | SLOTTED WASHER |
54. | [1] | 141450-2100 | PLATE |
57. | [2] | 010206-3020 | HEX-SOCKET-HEAD CAP SCREW |
59. | [1] | 141485-0602 | O-RING |
60. | [1] | 141291-5100 | CONTROL RACK |
61. | [1] | 141231-0901 | STOP SCREW |
62. | [1] | 014151-0120 | CONICAL SPRING WASHER |
68. | [1] | 141456-1000 | CYLINDER |
68. | [1] | 141456-1000 | CYLINDER |
69. | [1] | 029332-8010 | GASKET |
77. | [1] | 141292-3500 | CONTROL SLEEVE |
81. | [1] | 141245-2000 | POINTER |
82/1. | [0] | 023500-6210 | PLAIN WASHER D11&6.4T1.5 |
82/1. | [0] | 029300-6010 | PLAIN WASHER D11&6.4T0.8 |
82/1. | [0] | 029300-6020 | PLAIN WASHER D11&6.4T0.35 |
83. | [1] | 020006-1440 | BLEEDER SCREW M6P1L14 |
110. | [1] | 141418-2600 | SET OF NUTS |
111. | [1] | 141403-2000 | GASKET |
160. | [1] | 141418-2600 | SET OF NUTS |
161. | [1] | 141403-2000 | GASKET |
167. | [1] | 150948-0000 | INLET UNION |
168. | [1] | 150949-0100 | EYE BOLT |
169. | [2] | 150521-0800 | GASKET |
Include in #1:
101491-9211
as _
Include in #2:
104265-3004
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
The following changes are adaptable to machines within the listed serial numbers and are effective with all machines after the listed serial numbers.
Illustration 1 g06325715
View of Air lines group on 966M, 972M, 966M XE, and 972M XE machines
(1) 415-8220 Hose
(2) 8T-6703 Hose Clamp
(3) 211-8073 Protection Cap
Illustration 2 g06325708
View of Air lines group on 980M and 982M machines
(1) 365-0045 Hose
(2) 8T-6703 Hose Clamp
(3) 211-8073 Protection Cap
Table 1
Required Parts
Item Qty New Part Number Part Name Former Part Number
1 1 415-8220 (1) Hose 415-8220
365-0045 (2) 365-0045
2 2 8T-6703 Hose Clamp (3) 296-5807
3 2 211-8073 Protection Cap 7X-1443
(1) For 966M, 972M, 966M XE, and 972M XE machines
(2) For 980M and 982M machines
(3) Torque for the hose clamps is 11 2 N m (97 18 lb in).If the CRS hose is found damaged on the above listed machines, replace the hose with same part number. Use hose clamp (2) and protection cap (3) to secure the new hose.The new hose clamp (2) replaces the existing 296-5807 Clamp. The new protection cap (3) replaces the existing 7X-1443 Protector on machines listed above.Torque the hose clamps (2) to 11 2 N m (97 18 lb in).