Information fuel-injection pump
BOSCH
9 410 617 825
9410617825
ZEXEL
104264-5062
1042645062
AKASAKA-DIESEL
001254272001
001254272001

Rating:
Components :
0. | INJECTION-PUMP ASSEMBLY | 104264-5062 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | |
10. | NOZZLE-HOLDER | |
11. | NOZZLE |
Scheme ###:
5. | [1] | 141176-1821 | PLUNGER-AND-BARREL ASSY |
7. | [1] | 141133-0500 | CAPSULE |
8. | [1] | 141403-1300 | GASKET |
12. | [1] | 141145-4721 | DELIVERY-VALVE ASSEMBLY |
17. | [1] | 141138-0900 | FITTING |
20. | [1] | 141118-2000 | O-RING |
21. | [1] | 141119-3600 | FLANGE BUSHING |
22. | [6] | 141124-1300 | BLEEDER SCREW |
25. | [1] | 141482-9600 | O-RING |
50. | [1] | 141215-5402 | COMPRESSION SPRING |
51. | [1] | 141216-1800 | SLOTTED WASHER |
52. | [1] | 141217-5500 | SLOTTED WASHER |
53. | [1] | 141218-7920 | GUIDE |
55. | [1] | 141220-1200 | LOCKING WASHER |
60. | [1] | 141291-1700 | CONTROL RACK |
77. | [1] | 141241-7200 | CONTROL SLEEVE |
81. | [1] | 141245-4200 | POINTER |
82/1. | [0] | 023500-6210 | PLAIN WASHER D11&6.4T1.5 |
82/1. | [0] | 029300-6010 | PLAIN WASHER D11&6.4T0.8 |
82/1. | [0] | 029300-6020 | PLAIN WASHER D11&6.4T0.35 |
83. | [1] | 020006-1440 | BLEEDER SCREW M6P1L14 |
93. | [1] | 141402-5200 | EYE BOLT |
110. | [1] | 141420-0800 | BLEEDER SCREW |
111. | [1] | 141403-1200 | GASKET |
160. | [1] | 141418-1400 | SET OF NUTS |
161. | [1] | 026508-1140 | GASKET D11.4&8.2T1 |
162. | [1] | 141480-0900 | COVER |
164. | [1] | 373658-1400 | CAPSULE |
165. | [1] | 026510-1340 | GASKET D13.4&10.2T1 |
170. | [1] | 141133-1000 | CAPSULE |
171. | [1] | 141403-1600 | GASKET |
Include in #1:
101491-9078
as _
Include in #2:
104264-5062
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
9 410 617 825
001254272001 AKASAKA-DIESEL
FUEL-INJECTION PUMP
* K 24FX PF-1GX PF
* K 24FX PF-1GX PF
Information:
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Note: The standard work for the laser mark has been updated.Problem
Illustration 1 g06273667During laser marking on these Reman 3400 HEUI injectors both Prime and Non-Prime injectors were marked with NP. This caused confusion with dealers and customers. The NP is thought to mean "Non-Prime" and the injectors are Prime injector part numbers. The prime injectors marked incorrectly with NP but were built and tested to the correct Prime part number and should be used in fuel systems for prime injectors. Dealers can remove the two letters if they decide the two letters cause too much confusion.Solution
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Illustration 2 g06273668
Prime HEUI injector
NP stands for "Non-Prime". Going forward only "Non-Prime" 3400 HEUI injectors will have the NP laser mark.
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Note: The standard work for the laser mark has been updated.Problem
Illustration 1 g06273667During laser marking on these Reman 3400 HEUI injectors both Prime and Non-Prime injectors were marked with NP. This caused confusion with dealers and customers. The NP is thought to mean "Non-Prime" and the injectors are Prime injector part numbers. The prime injectors marked incorrectly with NP but were built and tested to the correct Prime part number and should be used in fuel systems for prime injectors. Dealers can remove the two letters if they decide the two letters cause too much confusion.Solution
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Illustration 2 g06273668
Prime HEUI injector
NP stands for "Non-Prime". Going forward only "Non-Prime" 3400 HEUI injectors will have the NP laser mark.