Information fuel-injection pump
BOSCH
F 01G 09Y 00X
f01g09y00x
ZEXEL
104244-8061
1042448061
DAIHATSU
E206200030Z
e206200030z

Rating:
Components :
0. | INJECTION-PUMP ASSEMBLY | 104244-8061 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | |
10. | NOZZLE-HOLDER | |
11. | NOZZLE |
Scheme ###:
1. | [1] | 141054-1800 | PUMP HOUSING |
5. | [1] | 141175-1921 | PLUNGER-AND-BARREL ASSY C113 |
7. | [2] | 141133-1500 | CAPSULE |
7. | [2] | 141133-1500 | CAPSULE |
8. | [2] | 141403-1100 | GASKET |
8. | [2] | 141403-1100 | GASKET |
12. | [1] | 141142-6121 | DELIVERY-VALVE ASSEMBLY C40 |
12/1. | [1] | 141141-8300 | SEAT;D.V |
12/2. | [1] | 141141-8400 | SEAT;D.V |
12/3. | [1] | 016807-0030 | BALL |
12/4. | [1] | 141113-0601 | SLOTTED WASHER |
12/5. | [1] | 141112-7100 | COILED SPRING |
12/6. | [1] | 141117-9201 | FILLER PIECE |
12/7. | [1] | 016804-5030 | BALL |
12/8. | [1] | 141113-1500 | SLOTTED WASHER |
12/9. | [1] | 141112-8201 | COMPRESSION SPRING |
12/10. | [1] | 141117-9302 | FILLER PIECE |
12/11. | [2] | 141213-1400 | BEARING PIN |
12/12. | [2] | 141271-0200 | BEARING PIN |
12/13. | [2] | 029423-0080 | BEARING PIN |
12/14. | [1] | 141222-0400 | LOCKING WASHER |
16. | [1] | 141115-6000 | GASKET |
17. | [1] | 141136-7800 | FITTING |
20. | [1] | 029633-2040 | O-RING |
25. | [1] | 141482-9500 | O-RING |
50. | [1] | 141215-6000 | COMPRESSION SPRING |
51. | [1] | 141216-2400 | SLOTTED WASHER |
52. | [1] | 141217-6300 | SLOTTED WASHER |
53. | [1] | 141218-8200 | GUIDE |
55. | [1] | 141220-0300 | LOCKING WASHER |
60. | [1] | 141244-8601 | CONTROL RACK |
61. | [1] | 141226-4300 | BLEEDER SCREW |
77. | [1] | 141241-8400 | CONTROL SLEEVE |
81. | [1] | 141245-2000 | POINTER |
82/1. | [0] | 023500-6210 | PLAIN WASHER D11&6.4T1.5 |
82/1. | [0] | 029300-6010 | PLAIN WASHER D11&6.4T0.8 |
82/1. | [0] | 029300-6020 | PLAIN WASHER D11&6.4T0.35 |
83. | [1] | 020006-1440 | BLEEDER SCREW |
93. | [1] | 141402-2820 | EYE BOLT |
94. | [2] | 141403-1300 | GASKET |
110. | [1] | 140420-1600 | BLEEDER SCREW |
111. | [1] | 141403-1200 | GASKET |
160. | [1] | 141418-1101 | SET OF NUTS |
161. | [1] | 026506-1040 | GASKET |
162. | [1] | 141480-1100 | COVER |
163. | [1] | 029111-0010 | CAPSULE |
164. | [1] | 026510-1340 | GASKET |
Cross reference number
Zexel num
Bosch num
Firm num
Name
104244-8061
E206200030Z DAIHATSU
FUEL-INJECTION PUMP
* 24DX PF-1CX PF
* 24DX PF-1CX PF
Information:
Introduction
The problem that is identified below does not have a permanent solution. Until a permanent solution is known, use the solution that is listed below.Problem
A significant amount of HEUI pumps and injectors have been returned, but no cause of failure can be determined.Solution
Diagnostic procedures have been updated and have been incorporated into the following publications:
Special Instruction, REHS3819, "Procedure for Troubleshooting and Cleaning the Oil Rail System for the Hydraulic Electronic Unit Injector (HEUI)"
Troubleshooting, "Injection Actuation Pressure - Test"Note: These publications have been translated into Mandarin and Spanish.In addition, a new troubleshooting checklist is included with all service repair for HUEI pumps and HEUI injectors. The checklist is a summary of the diagnostic procedure steps to be confirmed before a suspect component is replaced. The checklist must be completed and returned with the suspect components in order to aid engineering to determine the cause of failure.Following the instructions step-by-step is critical in order to diagnose the failed component correctly. Do not skip steps in the procedures. Skipping steps in the procedure will lead to incorrect diagnosis of the problem.
The problem that is identified below does not have a permanent solution. Until a permanent solution is known, use the solution that is listed below.Problem
A significant amount of HEUI pumps and injectors have been returned, but no cause of failure can be determined.Solution
Diagnostic procedures have been updated and have been incorporated into the following publications:
Special Instruction, REHS3819, "Procedure for Troubleshooting and Cleaning the Oil Rail System for the Hydraulic Electronic Unit Injector (HEUI)"
Troubleshooting, "Injection Actuation Pressure - Test"Note: These publications have been translated into Mandarin and Spanish.In addition, a new troubleshooting checklist is included with all service repair for HUEI pumps and HEUI injectors. The checklist is a summary of the diagnostic procedure steps to be confirmed before a suspect component is replaced. The checklist must be completed and returned with the suspect components in order to aid engineering to determine the cause of failure.Following the instructions step-by-step is critical in order to diagnose the failed component correctly. Do not skip steps in the procedures. Skipping steps in the procedure will lead to incorrect diagnosis of the problem.