Information fuel-injection pump
BOSCH
9 410 617 408
9410617408
ZEXEL
104232-6000
1042326000

Rating:
Components :
0. | INJECTION-PUMP ASSEMBLY | 104232-6000 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | |
10. | NOZZLE-HOLDER | |
11. | NOZZLE |
Scheme ###:
5. | [1] | 142101-0120 | PLUNGER-AND-BARREL ASSY |
6. | [1] | 029332-5020 | GASKET D30&25T0.5 |
7. | [1] | 142106-1000 | CAPSULE |
8. | [1] | 026508-1240 | GASKET D11.9&8.2T1 |
12. | [1] | 142110-0220 | DELIVERY-VALVE ASSEMBLY |
13. | [1] | 140112-0500 | COMPRESSION SPRING |
16. | [1] | 142115-0300 | GASKET |
17. | [1] | 142116-0300 | FITTING |
50. | [1] | 142215-0200 | COMPRESSION SPRING |
51. | [1] | 142216-0100 | SLOTTED WASHER |
53. | [1] | 140218-0400 | GUIDE |
55. | [1] | 140220-0200 | LOCKING WASHER |
60. | [1] | 142223-3820 | CONTROL RACK |
61. | [1] | 142226-1300 | BLEEDER SCREW |
68. | [1] | 142233-0000 | COILED SPRING |
70. | [1] | 029601-4000 | LOCKING WASHER |
77. | [1] | 142241-0400 | CONTROL SLEEVE |
81. | [1] | 141245-2000 | POINTER |
82/1. | [0] | 023500-6210 | PLAIN WASHER D11&6.4T1.5 |
82/1. | [0] | 029300-6010 | PLAIN WASHER D11&6.4T0.8 |
82/1. | [0] | 029300-6020 | PLAIN WASHER D11&6.4T0.35 |
82B. | [1] | 029310-6220 | SHIM D11.5&6.5T0.10 |
83. | [1] | 029050-6400 | FLAT-HEAD SCREW |
86. | [1] | 142249-0400 | FILLER PIECE |
87/1. | [0] | 023500-6210 | PLAIN WASHER D11&6.4T1.5 |
87/1. | [0] | 029300-6010 | PLAIN WASHER D11&6.4T0.8 |
87/1. | [0] | 029300-6020 | PLAIN WASHER D11&6.4T0.35 |
88. | [1] | 029050-6140 | FLAT-HEAD SCREW |
110. | [1] | 141420-0400 | BLEEDER SCREW |
111. | [1] | 029330-6070 | GASKET |
Cross reference number
Zexel num
Bosch num
Firm num
Name
104232-6000
9 410 617 408
FUEL-INJECTION PUMP
* K
* K
Information:
Engine Crankshaft Will Not Turn
Possible Causes/Corrections Low Or No Battery VoltageCheck battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge to the battery. If battery will not hold a charge, load test the battery as shown in the Electrical System of the Testing and Adjusting Section of this Service Manual. Defective Switch, Defective Wiring Or Connection In Switch CircuitWith ignition switch in START position, check voltage at switch connection on starter solenoid. If there is no voltage, or if the voltage is low at this connection, check wiring, connections, ignition switch, and magnetic switch (if used). Defective Cable Or Connection; Battery To StarterWith ignition switch in the START position, check voltage at connection of battery cable to starter. If there is no voltage, or if the voltage is low at this connection and there is good voltage at the battery, check for defective cable or connection between the
Possible Causes/Corrections Low Or No Battery VoltageCheck battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge to the battery. If battery will not hold a charge, load test the battery as shown in the Electrical System of the Testing and Adjusting Section of this Service Manual. Defective Switch, Defective Wiring Or Connection In Switch CircuitWith ignition switch in START position, check voltage at switch connection on starter solenoid. If there is no voltage, or if the voltage is low at this connection, check wiring, connections, ignition switch, and magnetic switch (if used). Defective Cable Or Connection; Battery To StarterWith ignition switch in the START position, check voltage at connection of battery cable to starter. If there is no voltage, or if the voltage is low at this connection and there is good voltage at the battery, check for defective cable or connection between the
Have questions with 104232-6000?
Group cross 104232-6000 ZEXEL
104232-6000
9 410 617 408
FUEL-INJECTION PUMP