104207-3011 ZEXEL F 01G 09Y 024 BOSCH FUEL-INJECTION PUMP f01g09y024 1042073011 131011111

Information fuel-injection pump

BOSCH F 01G 09Y 024 f01g09y024

ZEXEL 104207-3011 1042073011

ISHIKAWAJIMA-S 131011111 131011111

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy FUEL-INJECTION PUMP 104207-3011 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104207-3011
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY	105148-1761
8.	Nozzle and Holder
9.	Open Pre:MPa(Kqf/cm2)	14.7{150}
10.	NOZZLE-HOLDER	105078-0300
11.	NOZZLE	105007-1330

Scheme ###:

5.	[3]	140161-0820	PLUNGER-AND-BARREL ASSY M37
12.	[3]	140110-3620	DELIVERY-VALVE ASSEMBLY K15
13.	[3]	140112-2800	COMPRESSION SPRING
16.	[3]	140115-2200	GASKET
17.	[3]	140116-7220	FITTING
20.	[3]	140118-0500	O-RING
30.	[3]	140131-0021	FLANGE BUSHING
31.	[3]	140271-0000	BEARING PIN
32.	[6]	140118-0400	O-RING
37.	[6]	140124-0100	FLAT-HEAD SCREW
40.	[3]	140200-2320	TAPPET
44.	[3]	140212-0300	BEARING PIN
45.	[1]	140213-0900	LOCKING WASHER
50.	[3]	140215-2000	COMPRESSION SPRING
51.	[3]	140216-1300	SLOTTED WASHER
52.	[3]	140254-2900	SLOTTED WASHER
53/1.	[1]	140254-1400	PLATE T1.80
53/1.	[1]	140254-1500	PLATE T1.85
53/1.	[1]	140254-1600	PLATE T1.90
53/1.	[1]	140254-1700	PLATE T1.95
53/1.	[1]	140254-1800	PLATE T2.00
53/1.	[1]	140254-1900	PLATE T2.05
53/1.	[1]	140254-2000	PLATE T2.10
53/1.	[1]	140254-2100	PLATE T2.15
53/1.	[1]	140254-2200	PLATE T2.20
53/1.	[1]	140254-2300	PLATE T2.25
53/1.	[1]	140254-2400	PLATE T2.30
53/1.	[1]	140254-2500	PLATE T2.35
53/1.	[1]	140254-2600	PLATE T2.40
53/1.	[1]	140254-2700	PLATE T2.45
53/1.	[1]	140254-2800	PLATE T2.50
53/1.	[1]	140254-3100	PLATE T1.825
53/1.	[1]	140254-3200	PLATE T1.875
53/1.	[1]	140254-3300	PLATE T1.925
53/1.	[1]	140254-3400	PLATE T1.975
53/1.	[1]	140254-3500	PLATE T2.025
53/1.	[1]	140254-3600	PLATE T2.075
53/1.	[1]	140254-3700	PLATE T2.125
53/1.	[1]	140254-3800	PLATE T2.175
53/1.	[1]	140254-3900	PLATE T2.225
53/1.	[1]	140254-4000	PLATE T2.275
53/1.	[1]	140254-4100	PLATE T2.325
53/1.	[1]	140254-4200	PLATE T2.375
53/1.	[1]	140254-4300	PLATE T2.425
53/1.	[1]	140254-4400	PLATE T2.475
53/1.	[1]	140254-4500	PLATE T2.525
60.	[1]	140243-8320	CONTROL ROD
65.	[1]	140262-1900	PLATE
66.	[4]	140252-0001	FLAT-HEAD SCREW
77.	[3]	140241-4021	CONTROL SLEEVE
93.	[1]	140402-4020	EYE BOLT
93/1.	[1]	140402-3500	EYE BOLT
93/2.	[3]	026510-1340	GASKET
93/3.	[1]	140401-0700	BUSHING
93/4.	[1]	140401-0800	INLET UNION
110.	[1]	140420-2400	BLEEDER SCREW
111.	[1]	026506-1040	GASKET
170.	[1]	140405-0100	CAPSULE
171.	[1]	026510-1340	GASKET

Include in #2:

104207-3011 as INJECTION-PUMP ASSEMBLY

105866-4320 as _

Cross reference number

Zexel num

Bosch num

Firm num

Name

104207-3011

F 01G 09Y 024
NP-PFR3MD60R2T

131011111 ISHIKAWAJIMA-S

FUEL-INJECTION PUMP

Information:

Start By:a. remove cylinder headb. remove oil panc. remove cooling jets 1. Remove two rod cap bolts (1) from each rod. Remove rod caps (2).2. Using a soft hammer tape rod (3) away from crankshaft and remove bearing half (4). When removing cylinder pack, watch the rod and prevent it from catching on the block bore as it comes out.3. Install tooling (A) and remove cylinder pack (5). 4. Remove cylinder liner seal (6) at the base of the spacer block. 5. Remove the remainder of tooling (A) from cylinder pack (5) and then remove the rod and piston from the cylinder liner. The following steps are for the installation of the cylinder pack.6. Install a new cylinder liner seal, lubricate the seal with engine oil. Some engines use pistons which have the word "FRONT" stamped on the crown of the piston. Make sure the word "FRONT" is toward the front of the engine when the piston is installed. The etched number on the connecting rod must be on the right side and must be installed in the corresponding cylinder. Paint a thin coat of 9U-5839 Liquid Gasket at the very bottom of the seal flange on the cylinder liner. Allow the Liquid Gasket to dry to touch. Do not apply Liquid Gasket between the engine spacer block and cylinder block surfaces. Using excessive amounts of liquid gasket material on the liner flange seat can cause oil leaks due to distortion of the o-ring seals between the spacer block and cylinder block.7. Lubricate the lower portion of the cylinder liner with engine oil. Be sure the corresponding crankshaft throw is at bottom center. Position cylinder pack (5) and guide rod (3) into place. Use Tooling (B) and press cylinder (5) into place.8. With rod (3) in this position, install the upper half of rod bearing (4). Be sure the bearing tab properly engages the slot in the connecting rod. Lubricate the bearing surface with engine oil and tap the piston down with a rubber mallet until the rod and bearing contacts the crankshaft.9. With rod cap bearing in place and oiled, install rod cap (2). Lubricate rod bolts (1) with 2P-256 Thread Lubricant. Install rod bolts (1) and torque to 130 7 N m (95 5 lb ft). Mark each bolt head and then tighten each bolt by an additional 60 5° (1/6 turn).End By:a. Install cooling jets.b. Install oil pan.c. Install cylinder head.