104198-0151 ZEXEL 9 410 617 785 BOSCH FUEL-INJECTION PUMP 9410617785 1041980151


 

Information fuel-injection pump

BOSCH 9 410 617 785 9410617785
ZEXEL 104198-0151 1041980151
104198-0151 FUEL-INJECTION PUMP
Rating:
10
Buy FUEL-INJECTION PUMP 104198-0151 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 104198-0151
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2)
10. NOZZLE-HOLDER
11. NOZZLE

Scheme ###:

5. [1] 141156-0520 PLUNGER-AND-BARREL ASSY
7. [2] 141133-4500 CAPSULE
7. [2] 141133-4500 CAPSULE
8. [2] 141107-0300 GASKET
8. [2] 141107-0300 GASKET
12. [1] 141140-9820 DELIVERY-VALVE ASSEMBLY
13. [1] 141112-6600 COMPRESSION SPRING
17. [1] 141137-0920 FITTING
20. [2] 141482-2800 O-RING
21. [1] 141119-3900 FLANGE BUSHING
22. [12] 141124-2300 BLEEDER SCREW
22. [12] 141124-2300 BLEEDER SCREW
24. [1] 011012-2520 SET OF NUTS
25. [1] 011112-3020 SET OF NUTS
26/1. [1] 141161-0800 SPACER BUSHING T4
26/1. [1] 141161-0900 SPACER BUSHING T4.5
26/1. [1] 141161-1000 SPACER BUSHING T5
26/1. [1] 141161-1100 SPACER BUSHING T5.5
26/1. [1] 141161-1200 SPACER BUSHING T6
26/1. [1] 141161-1300 SPACER BUSHING T6.5
26/1. [1] 141161-1400 SPACER BUSHING T7
26/1. [1] 141161-1500 SPACER BUSHING T7.5
26/1. [1] 141161-1600 SPACER BUSHING T8
26/1. [1] 141161-2800 SPACER BUSHING T3.5
26/1. [1] 141161-2900 SPACER BUSHING T8.5
27. [2] 141482-2900 O-RING
29. [2] 141124-2600 BLEEDER SCREW
40. [1] 141200-1120 TAPPET
42. [1] 141213-0500 PLATE
43. [2] 010212-3520 HEX-SOCKET-HEAD CAP SCREW
50. [1] 141215-3700 COMPRESSION SPRING
51. [1] 141216-3220 SLOTTED WASHER
52. [1] 141217-5800 SLOTTED WASHER
56. [1] 141254-0100 SPACER BUSHING
57. [1] 141209-0100 SHIM
57B. [1] 141209-0200 SHIM
57C. [1] 141209-0700 SHIM
58. [2] 010208-2020 HEX-SOCKET-HEAD CAP SCREW
60. [1] 141244-3900 CONTROL RACK
77. [1] 141241-7520 CONTROL SLEEVE
79. [1] 141482-0500 O-RING
81. [1] 141245-3920 POINTER
84. [1] 141240-0300 PINION
85. [1] 141440-0820 FLANGE BUSHING
87. [1] 141439-1400 BUSHING
88. [1] 141418-0100 BLEEDER SCREW
90. [2] 141438-1700 STUD
91. [2] 141439-1900 UNION NUT
93. [2] 141416-0500 CONNECTOR
94. [2] 141403-0300 GASKET
151. [1] 029926-0000 CAP
156. [1] 141455-0700 COVER;ACCUMULATOR
157. [1] 141456-0200 CYLINDER
158. [1] 141276-0900 PUMP PLUNGER
159. [2] 141457-0000 PISTON RING
160. [1] 141258-1800 COILED SPRING
161. [1] 141258-1900 COILED SPRING
162. [1] 141482-0400 O-RING
163. [1] 141235-0100 BEARING PIN
165. [1] 141217-7200 SLOTTED WASHER
168. [2] 141269-0100 HEX-SOCKET-HEAD CAP SCREW
169. [4] 141269-0100 HEX-SOCKET-HEAD CAP SCREW
170. [2] 141406-1400 GASKET
171. [1] 141450-0800 ORIFICE
180. [1] 141124-2700 CONNECTOR
181. [1] 141406-0900 GASKET D35&27.4T1.0
199. [1] 141130-1200 COVER
200. [1] 141130-1300 COVER
201. [1] 141482-0600 O-RING
210. [1] 141405-0600 CAPSULE
211. [1] 141406-0300 GASKET
212. [5] 141263-0600 BLEEDER SCREW
212. [5] 141263-0600 BLEEDER SCREW
212. [5] 141263-0600 BLEEDER SCREW
214. [2] 141482-0700 O-RING
215. [1] 141239-0520 FILLER PIECE
217. [1] 141209-1500 PLATE
218. [2] 141418-0400 BLEEDER SCREW
219. [4] 010708-2520 FLAT-HEAD SCREW
230. [1] 141266-0400 FLAT-HEAD SCREW
231. [1] 029341-2040 GASKET
250. [1] 141270-0300 HINGED LID
251. [1] 141406-0700 GASKET
252. [1] 141416-1300 CONNECTOR
253. [1] 141406-0300 GASKET
254. [1] 141439-2100 UNION NUT
255. [1] 141405-1900 CAPSULE
256. [1] 141406-0900 GASKET D35&27.4T1.0

Include in #1:

Include in #2:

104198-0151 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104198-0151 
9 410 617 785 
   
FUEL-INJECTION PUMP
K 24LF FUEL INJECTION PUMP PF-PC4-2 PF




Information:

Oils
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact the skin.Keep all exhaust manifold and turbocharger shields in place to protect hot exhaust from oil spray in the event of a line, tube or seal failure.Batteries
Battery electrolyte contains acid and can cause injury. Avoid contact with the skin and eyes.Wash hands after touching batteries and connectors. Use of gloves is recommended.Batteries give off flammable fumes which can explode. Ensure there is proper ventilation for batteries which are located in an enclosure.Always thaw a frozen battery before jump starting. Frozen batteries can explode.Do not smoke when observing battery electrolyte levels.Always wear protective glasses when working with batteries.Never disconnect any charging unit circuit or battery circuit cable from the battery when charging unit is operating. A spark can cause the flammable vapor mixture of hydrogen and oxygen to explode.Fire or Explosion Prevention
Fire may result from lubricating oil or fuel sprayed on hot surfaces causing personal injury and property damage. Inspect all lines and tubes for wear or deterioration. They must be routed, supported or clamped securely. Tighten all connections to the recommended torque. Leaks can cause fires.Determine whether the engine will be operated in an environment in which combustible gases could be drawn through the air inlet system. These gases could cause the engine to overspeed, which in turn could seriously damage the engine and result in bodily injury or property damage.If your application involves the presence of combustible gases, consult your Caterpillar dealer to obtain additional information concerning protection devices (i.e. air inlet shutoff) suitable for the application involved.All fuels, most lubricants and some coolant mixtures are flammable.Diesel fuel is flammable. Gasoline is flammable. The mixture of diesel and gasoline fumes is extremely explosive.Do not smoke while refueling or in a refueling area.Do not smoke in areas where batteries are charged, or where flammable materials are stored.Batteries give off flammable fumes which can explode.Keep all fuels and lubricants stored in properly marked containers and away from all unauthorized persons.Store all oily rags or other flammable material in a protective container, in a safe place.Do not weld or flame cut on pipes or tubes that contain flammable fluids. Clean them thoroughly with nonflammable solvent before welding or flame cutting on them.Remove all flammable materials such as fuel, oil and other debris before they accumulate on the engine.Do not expose the engine to flames, burning brush, etc., if at all possible.Shields (if equipped), which protect hot exhaust components from oil or fuel spray in the event of a line, tube or seal failure, must be installed correctly.Provide adequate and proper waste oil disposal. Oil and fuel filters must be properly installed and housing covers tightened to proper torque when being changed.Batteries must be kept clean, covers kept on all cells, recommended cables and connections used and battery box covers kept in place when operating.When starting from an external source, always connect the positive (+) jumper cable to the POSITIVE (+) terminal of the

Have questions with 104198-0151?





Group cross 104198-0151 ZEXEL

Niigata-Urawa 

 
11547003B 
FUEL-INJECTION PUMP

Niigata-Tekkou 

9 410 618 212 
11547003F 
FUEL-INJECTION PUMP
 
 

 
 

Niigata-Urawa 

9 410 618 213 
015538 
FUEL-INJECTION PUMP
9 410 618 213 
015539 
FUEL-INJECTION PUMP
 
 

Niigata-Urawa 

 
11547005B 
FUEL-INJECTION PUMP

Niigata-Tekkou 

9 410 618 214 
11547005F 
FUEL-INJECTION PUMP
104198-0151  
9 410 617 785 
 
FUEL-INJECTION PUMP
 
 

9 410 618 453 
 
FUEL-INJECTION PUMP

Nkk 

 
PC02242C 
FUEL-INJECTION PUMP
 
 
FUEL-INJECTION PUMP
 
 
FUEL-INJECTION PUMP

Ishikawajima-H 

9 410 617 163 
121040016 
FUEL-INJECTION PUMP
Back to top