Information fuel-injection pump
BOSCH
9 410 617 387
9410617387
ZEXEL
104147-0070
1041470070
MITSUBISHI-HEAV
4106534000
4106534000
Rating:
Components :
| 0. | INJECTION-PUMP ASSEMBLY | 104147-0070 |
| 1. | _ | |
| 2. | FUEL INJECTION PUMP | |
| 3. | NUMBER PLATE | |
| 4. | _ | |
| 5. | CAPSULE | |
| 6. | ADJUSTING DEVICE | |
| 7. | NOZZLE AND HOLDER ASSY | 105193-3044 |
| 8. | Nozzle and Holder | |
| 9. | Open Pre:MPa(Kqf/cm2) | 34.3{350} |
| 10. | NOZZLE-HOLDER | 105093-6005 |
| 11. | NOZZLE | 105011-9630 |
Scheme ###:
| 1. | [1] | 141054-8720 | PUMP HOUSING |
| 5. | [1] | 141175-4221 | PLUNGER-AND-BARREL ASSY |
| 6. | [1] | 141162-0000 | GASKET |
| 7. | [2] | 141133-4701 | CAPSULE |
| 7. | [2] | 141133-4701 | CAPSULE |
| 8. | [2] | 026514-1840 | GASKET D17.9&14.2T1 |
| 8. | [2] | 026514-1840 | GASKET D17.9&14.2T1 |
| 12. | [1] | 141142-6221 | DELIVERY-VALVE ASSEMBLY |
| 12/1. | [1] | 141141-8200 | SEAT;D.V. |
| 12/2. | [1] | 141141-8400 | SEAT;D.V |
| 12/3. | [1] | 016807-0030 | BALL |
| 12/4. | [1] | 141113-0601 | SLOTTED WASHER |
| 12/5. | [1] | 141112-7100 | COILED SPRING |
| 12/6. | [1] | 141117-9201 | FILLER PIECE |
| 12/7. | [1] | 016804-5030 | BALL |
| 12/8. | [1] | 141113-1500 | SLOTTED WASHER |
| 12/9. | [1] | 141112-8201 | COMPRESSION SPRING |
| 12/10. | [1] | 141117-9302 | FILLER PIECE |
| 12/11. | [2] | 141213-1400 | BEARING PIN |
| 12/12. | [2] | 141271-0200 | BEARING PIN |
| 12/13. | [2] | 029423-0080 | BEARING PIN |
| 12/14. | [1] | 141222-0400 | LOCKING WASHER |
| 16. | [1] | 141115-5700 | GASKET |
| 17. | [1] | 141137-1500 | FITTING |
| 20. | [1] | 029633-2040 | O-RING |
| 40. | [1] | 141200-2520 | TAPPET |
| 44. | [1] | 141212-0300 | BEARING PIN |
| 50. | [1] | 141215-5100 | COMPRESSION SPRING |
| 51. | [1] | 141216-3400 | SLOTTED WASHER |
| 52. | [1] | 141217-5200 | SLOTTED WASHER |
| 56/1. | [1] | 141254-0700 | PLATE T7.3 |
| 56/1. | [1] | 141254-0800 | PLATE T7.6 |
| 56/1. | [1] | 141254-0900 | PLATE T7.9 |
| 56/1. | [1] | 141254-1000 | PLATE T8.2 |
| 56/1. | [1] | 141254-1100 | PLATE T8.5 |
| 60. | [1] | 141244-4501 | CONTROL RACK |
| 61. | [1] | 141267-0500 | FLAT-HEAD SCREW |
| 62. | [1] | 013020-8140 | UNION NUT M8P1.25H6.5 |
| 77. | [1] | 141241-6800 | CONTROL SLEEVE |
| 93. | [1] | 141402-2100 | EYE BOLT |
| 110. | [1] | 141420-0700 | BLEEDER SCREW |
| 111. | [1] | 141403-1400 | GASKET |
| 160. | [1] | 141133-0300 | CAPSULE |
| 161. | [1] | 029331-0020 | GASKET |
| 212. | [1] | 141482-2400 | O-RING |
| 220. | [1] | 141260-1600 | CONTROL LEVER |
| 221. | [1] | 141282-0300 | FLAT-HEAD SCREW |
Cross reference number
Zexel num
Bosch num
Firm num
Name
104147-0070
4106534000 MITSUBISHI-HEAV
FUEL-INJECTION PUMP
K 24DW FUEL INJECTION PUMP PF-R1CD PF
K 24DW FUEL INJECTION PUMP PF-R1CD PF
Information:
START BY:a. remove valve coversb. remove rocker shaft assemblies and pushrodsc. remove fuel injection nozzles (earlier)
Be sure that the piston is at Top Center so that the valves will be held in position when the springs are removed.
1. Remove the valve cover bases.2. Remove the valve stem locks with tooling (A) using the following procedure: a. Install adapter plate (1) with two OS1618 (5/16-18 x 1 in.) bolts.b. Install stud (2) and nut (3). Tighten the nut. c. Install plate (4), washer (5) and nut (6). Tighten the nut until the locks are free.d. Remove locks (7), and remove the nut, washer and plate from the stud. Remove the stud and adapter plate from the fuel injection nozzle adapter. 3. Remove rotocoil (8), spring (9) and washer (10). 4. Use tool (B) to remove fuel injection nozzle adapter (11) from the cylinder head assembly. 5. Remove washers (12) and seals (13) from adapters (11).Install Fuel Injection Nozzle Adapters (Earlier)
1. Inspect seals (3) for damage or wear, and make a replacement if necessary.2. Install washers (1) and seals (3) on adapters (2).3. Put liquid soap in the bores of the cylinder head and on the seals of the fuel injection nozzle adapters.4. Put 5P3931 Anti-Seize Compound on the threads of adapter (2), and install the adapters in the cylinder head assembly. 5. Use tool (A), and tighten the adapters to a torque of 205 14 N m (150 10 lb.ft.). 6. Install washers (6), springs (5) and rotocoils (4). 7. Use tool (B), and compress the springs until locks (7) can be installed. Install locks (7) on the valve stems, and remove tool (B).8. Install the valve cover base. Tighten the valve cover base mounting bolts to a torque of 14 3 N m (10 2 lb.ft.).END BY:a. install fuel injection nozzles (earlier)b. install rocker shaft assemblies and push rodsc. install valve covers
Be sure that the piston is at Top Center so that the valves will be held in position when the springs are removed.
1. Remove the valve cover bases.2. Remove the valve stem locks with tooling (A) using the following procedure: a. Install adapter plate (1) with two OS1618 (5/16-18 x 1 in.) bolts.b. Install stud (2) and nut (3). Tighten the nut. c. Install plate (4), washer (5) and nut (6). Tighten the nut until the locks are free.d. Remove locks (7), and remove the nut, washer and plate from the stud. Remove the stud and adapter plate from the fuel injection nozzle adapter. 3. Remove rotocoil (8), spring (9) and washer (10). 4. Use tool (B) to remove fuel injection nozzle adapter (11) from the cylinder head assembly. 5. Remove washers (12) and seals (13) from adapters (11).Install Fuel Injection Nozzle Adapters (Earlier)
1. Inspect seals (3) for damage or wear, and make a replacement if necessary.2. Install washers (1) and seals (3) on adapters (2).3. Put liquid soap in the bores of the cylinder head and on the seals of the fuel injection nozzle adapters.4. Put 5P3931 Anti-Seize Compound on the threads of adapter (2), and install the adapters in the cylinder head assembly. 5. Use tool (A), and tighten the adapters to a torque of 205 14 N m (150 10 lb.ft.). 6. Install washers (6), springs (5) and rotocoils (4). 7. Use tool (B), and compress the springs until locks (7) can be installed. Install locks (7) on the valve stems, and remove tool (B).8. Install the valve cover base. Tighten the valve cover base mounting bolts to a torque of 14 3 N m (10 2 lb.ft.).END BY:a. install fuel injection nozzles (earlier)b. install rocker shaft assemblies and push rodsc. install valve covers