104141-0160 ZEXEL 9 410 617 952 BOSCH FUEL-INJECTION PUMP 9410617952 1041410160


 

Information fuel-injection pump

BOSCH 9 410 617 952 9410617952
ZEXEL 104141-0160 1041410160
104141-0160 FUEL-INJECTION PUMP
Rating:
64
Buy FUEL-INJECTION PUMP 104141-0160 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 104141-0160
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY 105123-5180
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2) 21.6{220}
10. NOZZLE-HOLDER 105053-6180
11. NOZZLE 105011-6070

Scheme ###:

1. [1] 141051-0500 PUMP HOUSING
5. [1] 141170-0120 PLUNGER-AND-BARREL ASSY
6. [1] 029333-3010 GASKET
7. [1] 141106-8000 CAPSULE
7. [1] 141106-8000 CAPSULE
8. [1] 029340-8020 GASKET
8. [1] 029340-8020 GASKET
12. [1] 141110-5320 DELIVERY-VALVE ASSEMBLY
13. [1] 141112-2200 COMPRESSION SPRING
16. [1] 141115-4400 GASKET
17. [1] 141126-1400 FITTING
18. [1] 141117-3600 FILLER PIECE
20. [1] 029633-2040 O-RING
50. [1] 141215-0700 COMPRESSION SPRING
51. [1] 141216-2400 SLOTTED WASHER
52. [1] 141217-0300 SLOTTED WASHER
53. [1] 141218-4500 GUIDE
55. [1] 141220-0300 LOCKING WASHER
60. [1] 141230-8700 CONTROL RACK
61. [1] 141226-3100 BLEEDER SCREW
77. [1] 141241-0900 CONTROL SLEEVE
81. [1] 141245-2000 POINTER
82/1. [0] 023500-6210 PLAIN WASHER D11&6.4T1.5
82/1. [0] 029300-6010 PLAIN WASHER D11&6.4T0.8
82/1. [0] 029300-6020 PLAIN WASHER D11&6.4T0.35
83. [1] 020006-1440 BLEEDER SCREW M6P1L14
92. [1] 029701-8280 INLET UNION
93. [1] 029731-8160 EYE BOLT
94. [2] 026518-2240 GASKET D21.9&18.2T1
110. [1] 140420-1800 BLEEDER SCREW
110. [1] 140420-1800 BLEEDER SCREW
111. [1] 026506-1040 GASKET D9.9&6.2T1
111. [1] 026506-1040 GASKET D9.9&6.2T1

Include in #1:

Include in #2:

104141-0160 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104141-0160 
9 410 617 952 
NP-PF1CD170S00N7 
   
FUEL-INJECTION PUMP
K 24DA FUEL INJECTION PUMP PF-1C(D) PF




Information:

preparatory step: a) separate governor from fuel injection pump housing. 1. Remove the fuel injection pump as follows: a) Remove the protective cap and the felt washer (1). b) Install wrench (A) and remove retaining bushing (2) from housing.c) Remove the seal (3). d) Install extractor (B).e) Lift the fuel injection pump out of the housing.f) Remove the spacer (4). Keep the spacers (4) and pumps together, and identified as to their location in the fuel injection pump housing.2. Disassemble the fuel injection pumps as follows: a) Remove the bonnet (5), ring (6), spring (7), and check valve (8) from the barrel (9).b) Remove the plunger assembly (10), washer (11), and spring (12) from the barrel (9).
While disassembling and assembling fuel injection pump, exercise considerable care to prevent damage to plunger surfaces. The barrel and plunger assemblies are matched, and the individual parts are not interchangeable with other barrels or plunger assemblies.
3. Remove the rack (13).4. Remove the lifters (14). Keep the lifters identified and together with their respective pumps and spacers. 5. Remove the camshaft retaining plate (15), bolt and lock. 6. Remove the spring (16) and the gear assembly (17) from the camshaft. 7. Remove the camshaft (19). 8. Using tool (C), remove the camshaft bearings from the fuel injection pump housing.9. Remove the two rack bearings (18) from the fuel injection pump housing.Assemble Fuel Injection Pump Housing
1. Using tool group (C), install the camshaft bearings in the fuel injection pump housing. Install the bearing in governor end of housing so the oil hole in bearing is aligned with oil hole in housing. Install the camshaft bearings flush with outer ends of fuel injection pump housing. 2. Using tool (D), install the two rack bearings in the fuel injection pump housing. Install the bearing in governor end of housing so it will be recessed .195 .005 in. (4,953 0,127 mm) from face of housing. Install the rack bearing in accessory drive end of housing so it will be flush with face of fuel injection pump housing. 3. Lubricate the camshaft with clean SAE 30 engine oil. Install the camshaft in fuel injection pump housing. 4. Postion the governor drive gear (1) and spring (2) on the camshaft. Install the camshaft retaining plate (3), bolt, and lock. 5. Install the lifters (4) in their respective positions in housing. Lubricate the rack generously with clean SAE 30 engine oil. Install the rack (5) into fuel injection pump housing with the slot in rack toward the governor end of housing.6. Install the spacers in their respective positions in housing. If new lifters and pumps are to be installed, it will be necessary to set the fuel pump timing dimension. See FUEL INJECTION PUMP TIMING DIMENSION SETTING-OFF ENGINE in TESTING AND ADJUSTING.7. Assemble the fuel injection pumps as follows: a) Lubricate all parts generously with clean fuel oil.b) Install the spring, washer, and plunger in the barrel.c) Install the spring, check valve, bonnet, and ring on the barrel.
Do

Have questions with 104141-0160?





Group cross 104141-0160 ZEXEL

104141-0160  
9 410 617 952 
NP-PF1CD170S00N7 
 
FUEL-INJECTION PUMP
Back to top