Information fuel-injection pump
BOSCH
F 01G 09Y 037
f01g09y037
ZEXEL
104139-4181
1041394181
KUBOTA
1G85251012
1g85251012
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
IMIFAFTAbT 1G852-51010 1G852-51012 1G922-51014 Fuel Injection Pump for Kubota V2403 V2203 Engine for Bobcat 331 334 335 E42 E45 S130 S150 S185 S175 S510 S530 T110 T140 T190
IMIFAFTAbT Part Name:Fuel Injection Pump 1G852-51010 1G852-51012 1G922-51014 || Part Number:1G852-51010 1G852-51012 1G922-51014 || APPlication: Compatible For Kubota V2403 V2203 Engine for Bobcat 331 334 335 E42 E45 S130 S150 S185 S175 S510 S530 T110 T140 T190 || If you are not sure if the product is suitable please leave us a message and send us your original || product picture and part number and we will send the correct part after confirmation
IMIFAFTAbT Part Name:Fuel Injection Pump 1G852-51010 1G852-51012 1G922-51014 || Part Number:1G852-51010 1G852-51012 1G922-51014 || APPlication: Compatible For Kubota V2403 V2203 Engine for Bobcat 331 334 335 E42 E45 S130 S150 S185 S175 S510 S530 T110 T140 T190 || If you are not sure if the product is suitable please leave us a message and send us your original || product picture and part number and we will send the correct part after confirmation
IMELBUFF 1G852-51012 1G852-51010 Fuel Injection Pump for Kubota V2403 V2203 Engine Bobcat S130 S150 S160 S175 S185 S450 S510 S530 T140 T190 331 334 335 430 5600 Loader Excavator
IMELBUFF 🚜Part Number: 1G852-51010 1G852-51011 1G852-51012 104139-4180 104139-4181 || 🚜Engine Model: for Kubota Engine V2203, V2403, V2403-M || 🚜Vehicle Application: for Bobcat Excavator 331 334 335 430 5600; Skid Steer Loader S130 S150 S160 S175 S185 S450 S510 S530 T140 T190 || 🚜Warm Tips: If you are not sure that the pump is suitable for your vehicle, please send us email with your vehicle engine model and fuel pump part number || 🚜Service: 6-months-warranty and 24 hour support for customer service. Please feel free to contact us by email if you have any question with the product
IMELBUFF 🚜Part Number: 1G852-51010 1G852-51011 1G852-51012 104139-4180 104139-4181 || 🚜Engine Model: for Kubota Engine V2203, V2403, V2403-M || 🚜Vehicle Application: for Bobcat Excavator 331 334 335 430 5600; Skid Steer Loader S130 S150 S160 S175 S185 S450 S510 S530 T140 T190 || 🚜Warm Tips: If you are not sure that the pump is suitable for your vehicle, please send us email with your vehicle engine model and fuel pump part number || 🚜Service: 6-months-warranty and 24 hour support for customer service. Please feel free to contact us by email if you have any question with the product
Fuel Injection Pump 1G852-51010 1G852-51011 1G852-51012 Compatible for Kubota V2403 V2203 Engine Compatible for Bobcat 331 334 335 E42 E45 S130 S150 S185 S175 S510 S450 S530 T110 T140 T190 Excavator
EXKATCC Product Name:Fuel Injection Pump || Replaces Number:1G852-51010 1G852-51011 1G852-51012 || Application:Compatible for Kubota V2403 V2203Engine Compatible for Bobcat 331 334 335 E42 E45 S130 S150 S185 S175 S510 S450 S530 T110 T140 T190 Excavator || Tips: Before purchasing, please carefully confirm whether the part number and compatible machine model match. || Notice: Our product is air freight express, striving to shorten the downtime of customer equipment
EXKATCC Product Name:Fuel Injection Pump || Replaces Number:1G852-51010 1G852-51011 1G852-51012 || Application:Compatible for Kubota V2403 V2203Engine Compatible for Bobcat 331 334 335 E42 E45 S130 S150 S185 S175 S510 S450 S530 T110 T140 T190 Excavator || Tips: Before purchasing, please carefully confirm whether the part number and compatible machine model match. || Notice: Our product is air freight express, striving to shorten the downtime of customer equipment
Include in #1:
107691-2680
as _
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
Bolts And Bolt Torque
A bolt which is too long may "bottom" before the head is tight against the part it is to hold. The threads can be damaged when a "long" bolt is removed.If a bolt is too short, there may not be enough threads engaged to hold the part securely.Apply proper torque values to all bolts and nuts when assembling Caterpillar equipment. When a specific torque value is required, the value is listed in the SPECIFICATIONS section of the Service Manual. Tighten all other bolts and nuts for general usage, hydraulic valve bodies, or taperlock studs to the torque values given in the torque charts.T-T-T Procedure
A torque-turn-tighten (T-T-T) procedure is used in many specifications and instructions.1. Clean the bolt and nut threads.2. Put lubricant on the threads and the seat face of the bolt and the nut.3. Turn the bolt or the nut tight according to the torque specification.4. Put a location mark on the part and on the bolt or the nut.5. Turn the bolt or the nut tighter the amount of degrees according to the specifications. The side of a nut or bolt head can be used for reference if a mark can not be put on. Torque Wrench Extension
When a torque wrench extension is used with a torque wrench, the torque indication on the torque wrench will be less than the real torque.
TORQUE WRENCH WITH TORQUE WRENCH EXTENSION
E: Torque wrench drive axis-to-torque wrench extension drive axis. W: Mark on handle-to-torque wrench drive axis.1. Put a mark on the handle. Measure the handle from the mark to the axis of the torque wrench drive (W).2. Measure the torque wrench extension from the torque wrench drive to the axis of the torque wrench extension drive (E).3. To get correct torque indication (TI) when the real torque (RT) is known: Example: W = 12 in. (304.8 mm); E = 2.56 in. (65.0 mm); RT (from specifications) = 125 lb. ft. (170 N m). 4. Hold the torque wrench handle with the longest finger of the hand over the mark on the handle to get the real torque (RT) with low torque indication (TI) on the torque wrench.Locks
Flat metal locks must be installed properly to be effective. Bend one end of the lock around the edge of the part. Bend the other end against one flat surface of the nut or bolt head.Always install new locks in compartments which house moving parts.If lockwashers are installed on housings made of aluminum, use a flat washer between the lockwasher and the housing. Lines And Wires
When removing or disconnecting a group of lines or wires, tag each one to assure proper assembly.Lubrication
Where applicable, fill the compartments of the components serviced with the amount, type and grade of lubricant recommended in the Lubrication and Maintenance Guide.Rust Preventive Compound
Clean the rust preventive compound from all machined surfaces of new parts before installing them.Shims
When shims are removed, tie them together and identify them as to location. Keep shims clean and flat until they are
A bolt which is too long may "bottom" before the head is tight against the part it is to hold. The threads can be damaged when a "long" bolt is removed.If a bolt is too short, there may not be enough threads engaged to hold the part securely.Apply proper torque values to all bolts and nuts when assembling Caterpillar equipment. When a specific torque value is required, the value is listed in the SPECIFICATIONS section of the Service Manual. Tighten all other bolts and nuts for general usage, hydraulic valve bodies, or taperlock studs to the torque values given in the torque charts.T-T-T Procedure
A torque-turn-tighten (T-T-T) procedure is used in many specifications and instructions.1. Clean the bolt and nut threads.2. Put lubricant on the threads and the seat face of the bolt and the nut.3. Turn the bolt or the nut tight according to the torque specification.4. Put a location mark on the part and on the bolt or the nut.5. Turn the bolt or the nut tighter the amount of degrees according to the specifications. The side of a nut or bolt head can be used for reference if a mark can not be put on. Torque Wrench Extension
When a torque wrench extension is used with a torque wrench, the torque indication on the torque wrench will be less than the real torque.
TORQUE WRENCH WITH TORQUE WRENCH EXTENSION
E: Torque wrench drive axis-to-torque wrench extension drive axis. W: Mark on handle-to-torque wrench drive axis.1. Put a mark on the handle. Measure the handle from the mark to the axis of the torque wrench drive (W).2. Measure the torque wrench extension from the torque wrench drive to the axis of the torque wrench extension drive (E).3. To get correct torque indication (TI) when the real torque (RT) is known: Example: W = 12 in. (304.8 mm); E = 2.56 in. (65.0 mm); RT (from specifications) = 125 lb. ft. (170 N m). 4. Hold the torque wrench handle with the longest finger of the hand over the mark on the handle to get the real torque (RT) with low torque indication (TI) on the torque wrench.Locks
Flat metal locks must be installed properly to be effective. Bend one end of the lock around the edge of the part. Bend the other end against one flat surface of the nut or bolt head.Always install new locks in compartments which house moving parts.If lockwashers are installed on housings made of aluminum, use a flat washer between the lockwasher and the housing. Lines And Wires
When removing or disconnecting a group of lines or wires, tag each one to assure proper assembly.Lubrication
Where applicable, fill the compartments of the components serviced with the amount, type and grade of lubricant recommended in the Lubrication and Maintenance Guide.Rust Preventive Compound
Clean the rust preventive compound from all machined surfaces of new parts before installing them.Shims
When shims are removed, tie them together and identify them as to location. Keep shims clean and flat until they are