Fuel injectors
  1. Home
  2. fuel
  3. #1041391020

104139-1020 ZEXEL 9 410 618 025 BOSCH FUEL-INJECTION PUMP 9410618025 1041391020 8973148962


 

Information fuel-injection pump

BOSCH 9 410 618 025 9410618025
ZEXEL 104139-1020 1041391020
ISUZU 8973148962 8973148962
104139-1020 FUEL-INJECTION PUMP
Rating:
53
Buy FUEL-INJECTION PUMP 104139-1020 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 104139-1020
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY 105118-6910
8. Nozzle and Holder 8-97314-897-0
9. Open Pre:MPa(Kqf/cm2) 14.7{150}
10. NOZZLE-HOLDER 105048-2260
11. NOZZLE 105017-3110

Scheme ###:

PUMP HOUSING
1. [1] 140051-9100 PUMP HOUSING
5. [1] 140163-3220 PLUNGER-AND-BARREL ASSY
12. [1] 140110-5620 DELIVERY-VALVE ASSEMBLY
13. [1] 140112-2900 COMPRESSION SPRING
16. [1] 140115-1400 GASKET
17. [1] 140116-6720 FITTING
20. [1] 140118-0301 O-RING
30. [1] 140131-0421 FLANGE BUSHING
32. [2] 140118-0201 O-RING
37. [2] 140124-0200 BLEEDER SCREW
40. [1] 140200-1620 TAPPET
44. [1] 140212-0500 BEARING PIN
45. [1] 140213-1800 LOCKING WASHER
50. [1] 140215-1900 COMPRESSION SPRING
51. [1] 140216-0800 SLOTTED WASHER
52. [1] 140217-2200 SLOTTED WASHER
53/1. [1] 140217-5000 PLATE D19T2.60
53/1. [1] 140217-5100 PLATE D19T2.65
53/1. [1] 140217-5200 PLATE D19T2.70
53/1. [1] 140217-5300 PLATE D19T2.75
53/1. [1] 140217-5400 PLATE D19T2.80
53/1. [1] 140217-5500 PLATE D19T2.85
53/1. [1] 140217-5600 PLATE D19T2.90
53/1. [1] 140217-5700 PLATE D19T2.95
53/1. [1] 140217-5800 PLATE D19T3.00
53/1. [1] 140217-5900 PLATE D19T3.05
53/1. [1] 140217-6000 PLATE D19T3.10
53/1. [1] 140217-6100 PLATE D19T3.15
53/1. [1] 140217-6200 PLATE D19T3.20
53/1. [1] 140217-6300 PLATE D19T3.25
53/1. [1] 140217-6400 PLATE D19T3.30
53/1. [1] 140217-6500 PLATE D19T3.35
53/1. [1] 140217-6600 PLATE D19T3.40
53/1. [1] 140217-6700 PLATE D19T3.45
53/1. [1] 140217-6800 PLATE D19T3.50
53/1. [1] 140217-6900 PLATE D19T3.55
53/1. [1] 140217-7000 PLATE D19T3.60
53/1. [1] 140217-7100 PLATE D19T3.65
53/1. [1] 140217-7200 PLATE D19T3.70
53/1. [1] 140217-7300 PLATE D19T3.75
53/1. [1] 140217-7400 PLATE D19T3.80
53/1. [1] 140217-7500 PLATE D19T3.85
53/1. [1] 140217-7600 PLATE D19T3.90
53/1. [1] 140217-7700 PLATE D19T3.95
53/1. [1] 140217-7800 PLATE D19T4.00
53/1. [1] 140217-7900 PLATE D19T4.05
53/1. [1] 140217-8000 PLATE D19T4.10
53/1. [1] 140253-2000 PLATE
53/1. [1] 140253-2100 PLATE
53/1. [1] 140253-2200 PLATE
53/1. [1] 140253-2300 PLATE
53/1. [1] 140253-2400 PLATE
53/1. [1] 140253-2500 PLATE
53/1. [1] 140253-2600 PLATE
53/1. [1] 140253-2700 PLATE
53/1. [1] 140253-2800 PLATE
53/1. [1] 140253-2900 PLATE
53/1. [1] 140253-3000 PLATE
53/1. [1] 140253-3100 PLATE
53/1. [1] 140253-3200 PLATE
53/1. [1] 140253-3300 PLATE
53/1. [1] 140253-3400 PLATE
53/1. [1] 140253-3500 PLATE
53/1. [1] 140253-3600 PLATE
53/1. [1] 140253-3700 PLATE
53/1. [1] 140253-3800 PLATE
53/1. [1] 140253-3900 PLATE
53/1. [1] 140253-4000 PLATE
53/1. [1] 140253-4100 PLATE
53/1. [1] 140253-4200 PLATE
53/1. [1] 140253-4300 PLATE
53/1. [1] 140253-4400 PLATE
53/1. [1] 140253-4500 PLATE
53/1. [1] 140253-4600 PLATE
53/1. [1] 140253-4700 PLATE
53/1. [1] 140253-4800 PLATE
53/1. [1] 140253-4900 PLATE
60. [1] 140243-6423 CONTROL RACK
77. [1] 140241-4200 CONTROL SLEEVE

Include in #1:

106873-2910 as _

Include in #2:

104139-1020 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
104139-1020 
9 410 618 025 
NP-PFR1KX80/1NP24 
8973148962  ISUZU
FUEL-INJECTION PUMP
K 23AA FUEL INJECTION PUMP PFR-1KX PFR




Information:

start by:a) separation of governor from fuel injection pump housing 1. Remove the protection caps and felt washers (1) from pumps.2. Use wrench (A) to remove bushings (2) that hold the fuel injection pumps into the housing. Remove seals (3).3. Use extractor (B) to remove the pumps from the pump housing. Put identification on the injection pumps as to their location in the pump housing.4. Remove bonnet (4), ring (5), spring (6) and check valve (7) from barrel (8).5. Remove plunger assembly (11), washer (10) and spring (9) from the barrel.
Be careful not to cause damage to plunger assemblies. Keep the same cylinder pump and plunger together, the plunger from one pump can not be installed in another group.
6. Remove rack (12) from the housing. 7. Remove spacers (13) and lifters (14) from the housing. Keep the spacers and lifters together with identification as to their location in the pump housing. 8. Remove two bolts (16), lock and two sleeves from the gear assembly.9. Remove gear assembly (15) from the camshaft. 10. Remove two bolts, plate (17) and the spacer that hold the camshaft in position in the pump housing. 11. Remove the camshaft from the pump housing. 12. Use tool group (C) to remove the camshaft bearings from the pump housing.13. Remove the bearings for the fuel rack from the pump housing.Assemble Fuel Injection Pump Housing
1. Use tooling (C) to install the camshaft bearings in the fuel injection pump housing. Install the camshaft bearing joints 15° from the vertical centerline of the bores. Install the front and rear camshaft bearings even with the fuel injection pump housing. Install the center camshaft bearing a distance of 4.81 .02 in. (122.2 0.5 mm) from the rear face of the fuel injection pump housing. 2. Use tooling (F) to install the bearing with a tab for the groove in the rack.3. Use tooling (E) to install the rear bearing for the rack. Install the bearing to a depth of .282 .005 in. (7.16 0.13 mm). The small holes in the rear bearing must be installed parallel to the vertical centerline of the pump. 4. Put clean engine oil on the camshaft. Install the camshaft in the pump housing. 5. Install the spacer, plate (1) and two bolts that hold the camshaft in place in the pump housing. 6. Put gear assembly (2) in position on the end of the camshaft. Be sure rod (3) is in the groove of the camshaft. 7. Install sleeves (4), lock and two bolts on the gear assembly. 8. Install spacers (5) with their respective lifters (6) in the pump housing. If new lifters and/or pumps are to be installed, make adjustment of the fuel pump timing dimension. See SETTING THE INJECTION PUMP TIMING DIMENSION: OFF ENGINE TESTING AND ADJUSTING. 9. Install rack (7) in the pump housing.10. Assemble the fuel injection pumps as follows: a) Put clean fuel on all parts.b) Install the spring, washers and plunger in the

Have questions with 104139-1020?





Group cross 104139-1020 ZEXEL

Isuzu 

104139-1000  
9 410 617 887 
8971952570 
FUEL-INJECTION PUMP
104139-1010  

104139-1011 
9 410 618 157 
NP-PFR1KX80/1NP20 
8972293680 
FUEL-INJECTION PUMP
104139-1011  
9 410 617 901 
NP-PFR1KX80/1NP20 
8972293682 
FUEL-INJECTION PUMP
104139-1020  
9 410 618 025 
NP-PFR1KX80/1NP24 
8973148962 
FUEL-INJECTION PUMP
104139-1030  
9 410 618 072 
NP-PFR1KX80/1NP25 
8973519850 
FUEL-INJECTION PUMP
104139-1040  
F 01G 09Y 01A 
NP-PFR1KX80/1NP33 
8980965800 
FUEL-INJECTION PUMP
Back to top