104139-1000 ZEXEL 9 410 617 887 BOSCH FUEL-INJECTION PUMP 9410617887 1041391000 8971952570

Information fuel-injection pump

BOSCH 9 410 617 887 9410617887

ZEXEL 104139-1000 1041391000

ISUZU 8971952570 8971952570

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy FUEL-INJECTION PUMP 104139-1000 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104139-1000
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY	105118-7750
8.	Nozzle and Holder	8-97195-258-0
9.	Open Pre:MPa(Kqf/cm2)	16.7{170}/20.6{210}
10.	NOZZLE-HOLDER	105048-2250
11.	NOZZLE	105017-2730

Scheme ###:

5.	[1]	140163-1420	PLUNGER-AND-BARREL ASSY
12.	[1]	140110-5320	DELIVERY-VALVE ASSEMBLY
13.	[1]	140112-2900	COMPRESSION SPRING
16.	[1]	140115-1400	GASKET
17.	[1]	140116-6720	FITTING
20.	[1]	016500-1520	O-RING
30.	[1]	140131-0421	FLANGE BUSHING
32.	[2]	016550-1920	O-RING
37.	[2]	140124-0200	BLEEDER SCREW
40.	[1]	140200-2620	TAPPET
44.	[1]	140212-0500	BEARING PIN
45.	[1]	140213-1800	LOCKING WASHER
50.	[1]	140215-1900	COMPRESSION SPRING
51.	[1]	140216-0800	SLOTTED WASHER
52.	[1]	140217-2200	SLOTTED WASHER
53/1.	[1]	140217-5000	PLATE D19T2.60
53/1.	[1]	140217-5100	PLATE D19T2.65
53/1.	[1]	140217-5200	PLATE D19T2.70
53/1.	[1]	140217-5300	PLATE D19T2.75
53/1.	[1]	140217-5400	PLATE D19T2.80
53/1.	[1]	140217-5500	PLATE D19T2.85
53/1.	[1]	140217-5600	PLATE D19T2.90
53/1.	[1]	140217-5700	PLATE D19T2.95
53/1.	[1]	140217-5800	PLATE D19T3.00
53/1.	[1]	140217-5900	PLATE D19T3.05
53/1.	[1]	140217-6000	PLATE D19T3.10
53/1.	[1]	140217-6100	PLATE D19T3.15
53/1.	[1]	140217-6200	PLATE D19T3.20
53/1.	[1]	140217-6300	PLATE D19T3.25
53/1.	[1]	140217-6400	PLATE D19T3.30
53/1.	[1]	140217-6500	PLATE D19T3.35
53/1.	[1]	140217-6600	PLATE D19T3.40
53/1.	[1]	140217-6700	PLATE D19T3.45
53/1.	[1]	140217-6800	PLATE D19T3.50
53/1.	[1]	140217-6900	PLATE D19T3.55
53/1.	[1]	140217-7000	PLATE D19T3.60
53/1.	[1]	140217-7100	PLATE D19T3.65
53/1.	[1]	140217-7200	PLATE D19T3.70
53/1.	[1]	140217-7300	PLATE D19T3.75
53/1.	[1]	140217-7400	PLATE D19T3.80
53/1.	[1]	140217-7500	PLATE D19T3.85
53/1.	[1]	140217-7600	PLATE D19T3.90
53/1.	[1]	140217-7700	PLATE D19T3.95
53/1.	[1]	140217-7800	PLATE D19T4.00
53/1.	[1]	140217-7900	PLATE D19T4.05
53/1.	[1]	140217-8000	PLATE D19T4.10
53/1.	[1]	140253-2000	PLATE
53/1.	[1]	140253-2100	PLATE
53/1.	[1]	140253-2200	PLATE
53/1.	[1]	140253-2300	PLATE
53/1.	[1]	140253-2400	PLATE
53/1.	[1]	140253-2500	PLATE
53/1.	[1]	140253-2600	PLATE
53/1.	[1]	140253-2700	PLATE
53/1.	[1]	140253-2800	PLATE
53/1.	[1]	140253-2900	PLATE
53/1.	[1]	140253-3000	PLATE
53/1.	[1]	140253-3100	PLATE
53/1.	[1]	140253-3200	PLATE
53/1.	[1]	140253-3300	PLATE
53/1.	[1]	140253-3400	PLATE
53/1.	[1]	140253-3500	PLATE
53/1.	[1]	140253-3600	PLATE
53/1.	[1]	140253-3700	PLATE
53/1.	[1]	140253-3800	PLATE
53/1.	[1]	140253-3900	PLATE
53/1.	[1]	140253-4000	PLATE
53/1.	[1]	140253-4100	PLATE
53/1.	[1]	140253-4200	PLATE
53/1.	[1]	140253-4300	PLATE
53/1.	[1]	140253-4400	PLATE
53/1.	[1]	140253-4500	PLATE
53/1.	[1]	140253-4600	PLATE
53/1.	[1]	140253-4700	PLATE
53/1.	[1]	140253-4800	PLATE
53/1.	[1]	140253-4900	PLATE
60.	[1]	140243-6422	CONTROL RACK
77.	[1]	140241-2700	CONTROL SLEEVE

Include in #1:

106873-2880 as _

Include in #2:

104139-1000 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num

Bosch num

Firm num

Name

104139-1000

9 410 617 887

8971952570 ISUZU

FUEL-INJECTION PUMP
* K

Information:

start by:a) remove fuel shutoff solenoidb) remove fuel ratio control1. Make a setting of the fuel injection pump timing as follows: a) Turn the engine clockwise (as seen from the front of the engine) with tool (B) to top center of the compression stroke of No. 1 piston. See FINDING TOP CENTER COMPRESSION POSITION FOR NO. 1 PISTON in TESTING AND ADJUSTING. b) Remove the plug from the side of fuel injection pump housing. Install tool (A) through the hole in pump housing and into the notch in the injection pump camshaft. If tool (A) can not be installed in the notch of the injection pump camshaft, the injection pump is not in time with the engine and the following procedure must be followed: a) Remove nuts (1). Remove cover (2) for the automatic timing advance.b) Loosen bolt (3) and hit the bolt with a soft hammer to loosen the automatic timing advance. c) Remove bolt (3) and washer (4). Install the bolt again.d) Turn the fuel injection pump drive shaft clockwise with bolt (3) until tool (A) can be put into the notch in the injection pump camshaft.e) Remove the bolt. Install washer (4) and bolt (3) so the washer is loose.
TYPICAL EXAMPLEf) Remove the timing bolt from the flywheel. Turn the engine 60° counterclockwise (as seen from the front of the engine) with tool (B).g) Tighten the bolt that holds the automatic timing advance by hand. Turn the engine clockwise (as seen from the front of the engine) with tool (B) until the engine is at top center compression stroke of No. 1 piston.h) Tighten bolt (3) to a torque of 15 lb.ft. (20 N m). Remove tool (A) from the fuel injection pump housing. Tighten bolt (3) to a torque of 110 10 lb.ft. (149 14 N m).
Do not tighten the bolt to final torque until tool (A) is removed.
i) Turn the crankshaft counterclockwise (as seen from the front of the engine) two complete revolutions and check the timing to see that timing is correct.j) If timing is not correct, do the above procedure again.k) Install the cover for the automatic timing advance and the nuts that hold it. 2. Disconnect fuel lines (5) and (7) from the fuel injection pump housing.3. Disconnect fuel injection lines (9) from the fuel injection pump housing. Install caps and plugs in all fuel line openings.4. Remove two bolts (8) that hold bracket (6) to the governor housing. 5. Fasten a nylon strap and a hoist to the fuel injection pump housing. Remove bolts (12) and (10) that hold the fuel injection pump housing to the cylinder block.6. Remove bolts (11) that hold the fuel injection pump housing to the fuel injection pump and governor drive housing.7. Remove fuel injection pump housing and governor. The weight is 70 lb. (32 kg).Remove Fuel Injection Pump Housing And Governor (Later)
start by:a) remove fuel shutoff solenoidb) remove fuel ratio control1. Make a setting of the fuel injection pump timing as