104135-3000 ZEXEL 9 410 617 269 BOSCH FUEL-INJECTION PUMP 9410617269 1041353000 8943751990

Information fuel-injection pump

BOSCH 9 410 617 269 9410617269

ZEXEL 104135-3000 1041353000

ISUZU 8943751990 8943751990

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy FUEL-INJECTION PUMP 104135-3000 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104135-3000
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY	105118-4980
8.	Nozzle and Holder	8-94375-200-0
9.	Open Pre:MPa(Kqf/cm2)	21.6{220}
10.	NOZZLE-HOLDER	105048-5030
11.	NOZZLE	105017-0990

Scheme ###:

5.	[3]	140154-2420	PLUNGER-AND-BARREL ASSY
12.	[3]	140110-5220	DELIVERY-VALVE ASSEMBLY
13.	[3]	140112-2900	COMPRESSION SPRING
16.	[3]	140115-1400	GASKET
17.	[3]	140116-7600	FITTING
18.	[3]	140117-1700	FILLER PIECE
20.	[3]	016500-1520	O-RING
30.	[3]	140131-0720	FLANGE BUSHING
32.	[6]	016550-1920	O-RING
37.	[6]	140124-0200	BLEEDER SCREW
40.	[3]	140200-1620	TAPPET
44.	[3]	140212-0300	BEARING PIN
45.	[1]	140213-1400	LOCKING WASHER
50.	[3]	140215-1900	COMPRESSION SPRING
51.	[3]	140216-0800	SLOTTED WASHER
52.	[3]	140217-2200	SLOTTED WASHER
53/1.	[1]	140217-5000	PLATE D19T2.60
53/1.	[1]	140217-5100	PLATE D19T2.65
53/1.	[1]	140217-5200	PLATE D19T2.70
53/1.	[1]	140217-5300	PLATE D19T2.75
53/1.	[1]	140217-5400	PLATE D19T2.80
53/1.	[1]	140217-5500	PLATE D19T2.85
53/1.	[1]	140217-5600	PLATE D19T2.90
53/1.	[1]	140217-5700	PLATE D19T2.95
53/1.	[1]	140217-5800	PLATE D19T3.00
53/1.	[1]	140217-5900	PLATE D19T3.05
53/1.	[1]	140217-6000	PLATE D19T3.10
53/1.	[1]	140217-6100	PLATE D19T3.15
53/1.	[1]	140217-6200	PLATE D19T3.20
53/1.	[1]	140217-6300	PLATE D19T3.25
53/1.	[1]	140217-6400	PLATE D19T3.30
53/1.	[1]	140217-6500	PLATE D19T3.35
53/1.	[1]	140217-6600	PLATE D19T3.40
53/1.	[1]	140217-6700	PLATE D19T3.45
53/1.	[1]	140217-6800	PLATE D19T3.50
53/1.	[1]	140217-6900	PLATE D19T3.55
53/1.	[1]	140217-7000	PLATE D19T3.60
53/1.	[1]	140217-7100	PLATE D19T3.65
53/1.	[1]	140217-7200	PLATE D19T3.70
53/1.	[1]	140217-7300	PLATE D19T3.75
53/1.	[1]	140217-7400	PLATE D19T3.80
53/1.	[1]	140217-7500	PLATE D19T3.85
53/1.	[1]	140217-7600	PLATE D19T3.90
53/1.	[1]	140217-7700	PLATE D19T3.95
53/1.	[1]	140217-7800	PLATE D19T4.00
53/1.	[1]	140217-7900	PLATE D19T4.05
53/1.	[1]	140217-8000	PLATE D19T4.10
53/1.	[1]	140253-2000	PLATE
53/1.	[1]	140253-2100	PLATE
53/1.	[1]	140253-2200	PLATE
53/1.	[1]	140253-2300	PLATE
53/1.	[1]	140253-2400	PLATE
53/1.	[1]	140253-2500	PLATE
53/1.	[1]	140253-2600	PLATE
53/1.	[1]	140253-2700	PLATE
53/1.	[1]	140253-2800	PLATE
53/1.	[1]	140253-2900	PLATE
53/1.	[1]	140253-3000	PLATE
53/1.	[1]	140253-3100	PLATE
53/1.	[1]	140253-3200	PLATE
53/1.	[1]	140253-3300	PLATE
53/1.	[1]	140253-3400	PLATE
53/1.	[1]	140253-3500	PLATE
53/1.	[1]	140253-3600	PLATE
53/1.	[1]	140253-3700	PLATE
53/1.	[1]	140253-3800	PLATE
53/1.	[1]	140253-3900	PLATE
53/1.	[1]	140253-4000	PLATE
53/1.	[1]	140253-4100	PLATE
53/1.	[1]	140253-4200	PLATE
53/1.	[1]	140253-4300	PLATE
53/1.	[1]	140253-4400	PLATE
53/1.	[1]	140253-4500	PLATE
53/1.	[1]	140253-4600	PLATE
53/1.	[1]	140253-4700	PLATE
53/1.	[1]	140253-4800	PLATE
53/1.	[1]	140253-4900	PLATE
60.	[1]	140243-4720	CONTROL RACK
77.	[3]	140241-2700	CONTROL SLEEVE
93.	[1]	027412-2440	EYE BOLT
94.	[2]	026512-1540	GASKET D15.4&12.2T1.50
112.	[1]	140420-1400	BLEEDER SCREW
113.	[1]	026508-1240	GASKET D11.9&8.2T1

Include in #1:

106673-7060 as _

Include in #2:

104135-3000 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num

Bosch num

Firm num

Name

104135-3000
104135-3001

9 410 617 269

8943751990 ISUZU

FUEL-INJECTION PUMP
* K

Information:

start by:a) remove oil pumpb) remove timing gear coverc) remove flywheel housingd) remove pistons For more detail about removal of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS. 1. Check each bearing cap (1) for its location on the engine. Each cap has an arrow which is toward the front of the block and a number which gives the location of that cap. Keep each bearing with the correct cap. 2. Remove bearing caps No. 2 through No. 4. Remove thrust plates from No. 3 upper bearing.3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 270 lb. (122 kg).
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface .25 .02 in. (6.4 0.5 mm).2. Install dowel (2) until it is extended from the surface .16 .02 in. (4.1 0.5 mm). 3. Heat crankshaft gear (3) to a maximum temperature of 400°F (204°C). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearances with tool (B).7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows: a) Tighten the bolts on the tab end of the caps first to a torque of 190 10 lb. ft. (260 14 N m).b) Tighten the bolts on the other end of the caps to a torque of 190 10 lb. ft. (260 14 N m).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end