104134-1000 ZEXEL 9 410 617 052 BOSCH FUEL-INJECTION PUMP 9410617052 1041341000

Information fuel-injection pump

BOSCH 9 410 617 052 9410617052

ZEXEL 104134-1000 1041341000

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy FUEL-INJECTION PUMP 104134-1000 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104134-1000
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY	105148-1231
8.	Nozzle and Holder	8-97069-342-1
9.	Open Pre:MPa(Kqf/cm2)	13.2{135}
10.	NOZZLE-HOLDER	105078-0130
11.	NOZZLE	105007-1010

Scheme ###:

5.	[1]	140154-2820	PLUNGER-AND-BARREL ASSY
12.	[1]	140110-3720	DELIVERY-VALVE ASSEMBLY
13.	[1]	140112-2900	COMPRESSION SPRING
16.	[1]	140115-1400	GASKET
17.	[1]	140116-7600	FITTING
18.	[1]	140117-1700	FILLER PIECE
20.	[1]	016500-1520	O-RING
30.	[1]	140131-0421	FLANGE BUSHING
32.	[2]	016550-1920	O-RING
37.	[2]	140124-0200	BLEEDER SCREW
40.	[1]	140200-1620	TAPPET
44.	[1]	140212-0500	BEARING PIN
45.	[1]	140213-1600	LOCKING WASHER
50.	[1]	140215-1900	COMPRESSION SPRING
51.	[1]	140216-0800	SLOTTED WASHER
52.	[1]	140217-2200	SLOTTED WASHER
53/1.	[1]	140217-5000	PLATE D19T2.60
53/1.	[1]	140217-5100	PLATE D19T2.65
53/1.	[1]	140217-5200	PLATE D19T2.70
53/1.	[1]	140217-5300	PLATE D19T2.75
53/1.	[1]	140217-5400	PLATE D19T2.80
53/1.	[1]	140217-5500	PLATE D19T2.85
53/1.	[1]	140217-5600	PLATE D19T2.90
53/1.	[1]	140217-5700	PLATE D19T2.95
53/1.	[1]	140217-5800	PLATE D19T3.00
53/1.	[1]	140217-5900	PLATE D19T3.05
53/1.	[1]	140217-6000	PLATE D19T3.10
53/1.	[1]	140217-6100	PLATE D19T3.15
53/1.	[1]	140217-6200	PLATE D19T3.20
53/1.	[1]	140217-6300	PLATE D19T3.25
53/1.	[1]	140217-6400	PLATE D19T3.30
53/1.	[1]	140217-6500	PLATE D19T3.35
53/1.	[1]	140217-6600	PLATE D19T3.40
53/1.	[1]	140217-6700	PLATE D19T3.45
53/1.	[1]	140217-6800	PLATE D19T3.50
53/1.	[1]	140217-6900	PLATE D19T3.55
53/1.	[1]	140217-7000	PLATE D19T3.60
53/1.	[1]	140217-7100	PLATE D19T3.65
53/1.	[1]	140217-7200	PLATE D19T3.70
53/1.	[1]	140217-7300	PLATE D19T3.75
53/1.	[1]	140217-7400	PLATE D19T3.80
53/1.	[1]	140217-7500	PLATE D19T3.85
53/1.	[1]	140217-7600	PLATE D19T3.90
53/1.	[1]	140217-7700	PLATE D19T3.95
53/1.	[1]	140217-7800	PLATE D19T4.00
53/1.	[1]	140217-7900	PLATE D19T4.05
53/1.	[1]	140217-8000	PLATE D19T4.10
53/1.	[1]	140253-2000	PLATE
53/1.	[1]	140253-2100	PLATE
53/1.	[1]	140253-2200	PLATE
53/1.	[1]	140253-2300	PLATE
53/1.	[1]	140253-2400	PLATE
53/1.	[1]	140253-2500	PLATE
53/1.	[1]	140253-2600	PLATE
53/1.	[1]	140253-2700	PLATE
53/1.	[1]	140253-2800	PLATE
53/1.	[1]	140253-2900	PLATE
53/1.	[1]	140253-3000	PLATE
53/1.	[1]	140253-3100	PLATE
53/1.	[1]	140253-3200	PLATE
53/1.	[1]	140253-3300	PLATE
53/1.	[1]	140253-3400	PLATE
53/1.	[1]	140253-3500	PLATE
53/1.	[1]	140253-3600	PLATE
53/1.	[1]	140253-3700	PLATE
53/1.	[1]	140253-3800	PLATE
53/1.	[1]	140253-3900	PLATE
53/1.	[1]	140253-4000	PLATE
53/1.	[1]	140253-4100	PLATE
53/1.	[1]	140253-4200	PLATE
53/1.	[1]	140253-4300	PLATE
53/1.	[1]	140253-4400	PLATE
53/1.	[1]	140253-4500	PLATE
53/1.	[1]	140253-4600	PLATE
53/1.	[1]	140253-4700	PLATE
53/1.	[1]	140253-4800	PLATE
53/1.	[1]	140253-4900	PLATE
60.	[1]	140243-6420	CONTROL RACK
77.	[1]	140241-2700	CONTROL SLEEVE
93.	[1]	027412-2440	EYE BOLT
94.	[2]	026512-1540	GASKET D15.4&12.2T1.50

Include in #1:

106673-7830 as _

Include in #2:

104134-1000 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num

Bosch num

Firm num

Name

104134-1000
104134-1020

9 410 617 052

FUEL-INJECTION PUMP
* K

Information:

This Program must be administered assoon as possible. When reporting the repair, use "PI30156" as the Partnumber and "7751" as the Group Number, "56" as the Warranty Claim DescriptionCode and "T" as the SIMS Description Code. Exception: If the repair isdone after failure, use "PI30156" as the Part Number, "7751" as the GroupNumber, "96" as the Warranty Claim Description Code, and "Z" as the SIMSDescription Code. The information supplied in this serviceletter may not be valid after the termination date of this program. Donot perform the work outlined in this Service Letter after the terminationdate without first contacting your Caterpillar product analyst. This Revised Service Letter replacesthe March 24, 2001 Service Letter. Changes were made to Parts Needed, ReworkProcedure, Service Claim Allowances, Owner Notification and Parts Disposition. This Service Letter should not be performedon engines with greater than 7500 miles (>12000 KM) or >150 hours.
COMPLETION DATE
TERMINATION DATE
September 30, 2001 March 31, 2002PROBLEM
Due to a manufacturing error, there is a possibilitythat numerous 1043568 Injector Pushrods missed the heat treating operation.Certain C-10, C-12, 3176C, and 3196 engines will need to have the injectorpushrods checked and possibly replaced. This Service letter should onlybe performed on engines with between 0 to 7500 miles (0 to 12000 kM) or0-150 hours.AFFECTED PRODUCT
Model Identification NumberTRUCK/COMMERCIAL ENGINESC-10 3CS18811 ? 193268YS7628 - 7646C-12 2KS61890 ? 632739SM277 - 3363176C IND 2AW1272 ? 13063196 IND 1DW611 ? 6143176C MAR 6BW498 ? 4993196 MAR 2XR3757 ? 38623176C Machine 3PD168 - 2023196 Machine 5ED216 - 2373176C Machine 7ZR5409 - 55163196 Machine 6AR2595 - 2635MACHINES725 AFX130-131, 142-145, 148-150,174, 177-179730 AGF217-218, 225-228345 AGS480, 562, 564, 566, 571,575, 578, 582-584ALB197APB110-112CFM27665E 6GS632, 634, 637, 639?649, 65275E 1HM310-3126HS647, 64985E 1NM230-2316JS668-669, 67295E 1SM282 ? 2896KS985, 987, 993PARTS NEEDED
AS REQUIRED
1043568 Injector Pushrods(depending on the results of the inspection,0?6 pushrods may be needed for the rework? Only individual pushrods foundto be soft need to be replaced)AS REQUIRED
Injector Group(depending on the results of the pushrodinspection , 0-6 injectors may be needed for the rework? An injector shouldbe replaced only if the pushrod for that particular injector isfound to be soft and if the engine has more than 200 MILES (322KM) or 20 HOURS.)ACTION REQUIRED
Remove the valve covers.
Using a medium to coarse flat file against thecup of the pushrod, stroke the file.
If the push rod is soft you will feel a distinctdrag as the file digs into the material.
If the push rod is hard the file will feel likeit is passing over glass as the file slides across the hard surface.
If you are not certain if a pushrod is soft orhard CALL YOUR TC OR THE CAT PRODUCT ANALYST AT:(800)447-4986.
If a pushrod is soft, remove the rocker arm andreplace the pushrod. Tighten the rocker stand bolts according to the torquevalue found in Service Manual.
IF A PUSHROD IS FOUND TO BE SOFT AND THE ENGINEHAS MORE THAN 200 miles (322 KM) OR 20 hours on it replace onlythe injector that is driven by the soft pushrod. Lubricate the two largero-ring seals with engine oil and install the injectors. Tighten the injectorhold down