105520-3061 ZEXEL F 019 Z1E 648 BOSCH f019z1e648 1055203061

Information

BOSCH F 019 Z1E 648 f019z1e648

ZEXEL 105520-3061 1055203061

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy None 105520-3061 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1.	[1]	155000-7020	GOVERNOR HOUSING
1/1.	[1]	155001-6120	GOVERNOR HOUSING
1/2.	[1]	155003-0600	CONTROL LEVER
1/3.	[1]	155004-0900	LEVER SHAFT
1/4.	[1]	155005-0200	COILED SPRING
1/5.	[1]	155006-0100	BLEEDER SCREW
1/7.	[1]	155411-7100	FLAT-HEAD SCREW
1/8.	[1]	155011-0200	HEXAGON NUT
1/9.	[2]	029010-6010	CAPSULE M6P1.0L7
1/9.	[2]	029010-6010	CAPSULE M6P1.0L7
1/10.	[2]	026506-1040	GASKET D9.9&6.2T1
1/10.	[2]	026506-1040	GASKET D9.9&6.2T1
1/11.	[0]	029310-8010	PLAIN WASHER D15&8.4T0.2
1/11B.	[0]	029310-8020	PLAIN WASHER D15&8.4T0.3
1/12.	[3]	029010-6680	BLEEDER SCREW
1/14.	[2]	029300-8010	PLAIN WASHER D15&8T1.00
1/14B.	[0]	029300-8030	PLAIN WASHER D15&8T1.50
1/15.	[2]	155012-0100	ADAPTOR
1/15.	[2]	155012-0100	ADAPTOR
1/16.	[1]	155013-0100	CAP
1/17.	[2]	029630-8060	O-RING
1/17.	[2]	029630-8060	O-RING
1/18.	[2]	025520-1210	SPLIT PIN
2.	[1]	154007-0200	ADAPTOR
3.	[1]	020018-1840	BLEEDER SCREW M8P1.25L18
4.	[4]	021006-1540	FLAT-HEAD SCREW
5.	[1]	153406-0400	BLEEDER SCREW
6.	[1]	014110-5440	LOCKING WASHER
7.	[1]	013020-5220	UNION NUT M5P0.8H4
8.	[1]	023500-6210	PLAIN WASHER D11&6.4T1.5
9.	[1]	025520-1210	SPLIT PIN
10.	[1]	155020-7920	DIAPHRAGM
11.	[1]	155031-1400	GOVERNOR SPRING
12/1.	[0]	155407-1100	SHIM D37&30.5T0.5
12/1.	[0]	155407-1200	SHIM D37&30.5T1.0
12/1.	[0]	155407-1300	SHIM D37&30.5T1.5
12/1.	[0]	155407-1400	SHIM D37&30.5T2.0
12/1.	[0]	155407-1500	SHIM D37&30.5T2.5
12/1.	[0]	155407-1600	SHIM D37&30.5T3.0
12/1.	[0]	155407-1700	SHIM D37&30.5T0.2
12/1.	[0]	155407-1800	SHIM D37&30.5T0.3
13.	[1]	155240-0500	COVER
14.	[1]	155019-0220	FILLER PIECE
15.	[4]	020105-1640	BLEEDER SCREW M5P0.8L16
15.	[4]	020105-1640	BLEEDER SCREW M5P0.8L16
18.	[1]	155241-0920	HEADLESS SCREW
21.	[1]	155245-0100	HEXAGON NUT
23.	[1]	029142-0010	CAPSULE
26.	[1]	029721-2050	JOINT CONNECTION
27.	[1]	029721-2040	JOINT CONNECTION
31.	[1]	155414-5500	CONTROL LEVER
40.	[1]	155404-3700	CAP
50.	[1]	014110-8440	LOCKING WASHER
51.	[1]	013020-8040	UNION NUT M8P1.25H7
100.	[1]	029621-7010	PACKING RING
140.	[1]	154390-0000	GASKET

Include in #1:

101431-9740 as GOVERNOR

Cross reference number

Zexel num

Bosch num

Firm num

Name

105520-3061

F 019 Z1E 648

* K

Information:

Flywheel
Installation of Flywheel Housing
Installation of flywheel housing(1) Install the oil seal to the flywheel housing.(2) Coat the contact surfaces of the crankcase and flywheel with ThreeBond 1104.(3) Align the holes in the flywheel housing and gasket with the dowel pins on the crankcase, and install them to the crankcase.Installation of Flywheel
(1) Install the flywheel to the crankshaft by aligning the hole with the dowel pin on the back-end of the crankshaft.(2) Place the washer and tighten the four bolts to the specified torque.
Installation of flywheelMeasurement of Flywheel Runout
Measure the flywheel runout with the flywheel installed to the crankshaft. If the standard value is exceeded, check the bolts for tightening condition and the mounting face for adhesion of foreign particles.
Measurement of face runout and circular runoutCylinder Head and Valve Mechanisms
Installation of Valve Stem Seal
(1) Apply engine oil to the valve stem, and insert it into the valve guide.(2) Place a new stem seal on the valve guide.(3) Using the stem seal installer, install the stem seal to the valve guide, making use of the valve stem as a guide.
Installation of valve stem sealInstallation of Valves and Valve Springs
(1) Place the valve spring and retainer on the valve guide, and install the valve cotter using the valve spring pusher.
Excessive compression of the valve spring can cause the retainer to contact the stem seal and damage the seal.
Installation of valve and valve spring(2) Using a soft-faced hammer, tap the top of the valve stem several times to make sure that the spring and valve cotter are securely installed.
Confirmation of secure valve cotter installationInstallation of Cylinder Head Gasket
(1) Make sure that the top face of the crankcase and piston upper surfaces are clean and free of dust.(2) Place a new gasket of the crankcase, making sure that the dowel pins on the top face of the crankcase enter the holes in the gasket.
Do not use a liquid gasket.
Installation of cylinder head gasketInstallation of Cylinder Head
Place the cylinder head on the head gasket, making sure that the dowel pins on the top face of the crankcase enters the holes in the cylinder head.
Installation of cylinder head assemblyTightening of Cylinder Head Bolts
Tighten the cylinder head bolts, following the tightening sequence shown in the diagram two or three times before reaching the specified torque.
Cylinder head bolt tightening sequenceAssembly of Rocker Arm and Rocker Shaft Assembly
When installing the rocker arms, make sure that the shaft assembly marks face the front of the engine, as shown in the diagram. After the assembly, make sure that the rocker arms move smoothly.
Assembly of rocker shaft assemblyInstallation of Pushrods
(1) Insert the pushrods in the cylinder head through the pushrod holes.(2) Make sure that the ball end of each pushrod rests securely on the curved surface of the tappet.Installation of Rocker Shaft Assemblies
(1) Install the valve caps.(2) When installing the rocker shaft brackets, tighten the long bolts first, then tighten the short bolts (reversal of removal sequence).
Installation of rocker shaft assemblyAdjustment of Valve Clearances
(1) Confirming the top dead center on the