Information
BOSCH
F 01G 29U 017
f01g29u017
ZEXEL
105019-2910
1050192910
Rating:
Cross reference number
Zexel num
Bosch num
Firm num
Name
105019-2910
F 01G 29U 017
C
Information:
Above 32°F (0°C)
Make sure no one is working on or close to the machine before starting the engine. Fasten seat belt.
1. Make certain TRANSMISSION NEUTRAL LOCK and PARKING BRAKE LOCKING lever is engaged. Move all implement controls to HOLD. 2. Insert the key in the disconnect switch and turn the switch ON.
Never turn the disconnect switch OFF with the engine running.
3. Move the governor control lever to the low idle position just past the detent. 4. Push in and turn the START switch to START. Release the switch when the engine starts.Below 32°F (0°C)
1. Follow steps 1-thru-4 for above 32°F (0°C). If engine does not start, push in the Starting Aid Button. A metered amount of starting fluid, sufficient to help start the engine, is released each time the Starting Aid Button is pushed in. 2. While cranking the engine use additional Starting Aid Fluid every 2 seconds, by pushing the button in and releasing it. 3. Release the START switch when the engine starts.4. If necessary continue the use of Starting Aid Fluid every 2 seconds after the engine starts, until it runs smoothly.
After every 30 seconds of cranking, allow 2 minutes for the starting motor to cool.
5. If extra battery capacity is needed, refer to the Operator's Guide SEBU5516 - 955L, 977L & 983B Track Type Loaders.6. Refer to the Operator's Guide for after starting checks, warm up procedure and engine shutdown. For starting below 0°F (-18°C) the use of optional cold weather starting aids is recommended. A coolant heater, jacket water heater or extra battery capacity may be required.
The Starting Aid Ether Bottle must be removed before transporting the machine. See the Lubrication and Maintenance Guide SEBU5515 for removal and replacing the bottle.
Make sure no one is working on or close to the machine before starting the engine. Fasten seat belt.
1. Make certain TRANSMISSION NEUTRAL LOCK and PARKING BRAKE LOCKING lever is engaged. Move all implement controls to HOLD. 2. Insert the key in the disconnect switch and turn the switch ON.
Never turn the disconnect switch OFF with the engine running.
3. Move the governor control lever to the low idle position just past the detent. 4. Push in and turn the START switch to START. Release the switch when the engine starts.Below 32°F (0°C)
1. Follow steps 1-thru-4 for above 32°F (0°C). If engine does not start, push in the Starting Aid Button. A metered amount of starting fluid, sufficient to help start the engine, is released each time the Starting Aid Button is pushed in. 2. While cranking the engine use additional Starting Aid Fluid every 2 seconds, by pushing the button in and releasing it. 3. Release the START switch when the engine starts.4. If necessary continue the use of Starting Aid Fluid every 2 seconds after the engine starts, until it runs smoothly.
After every 30 seconds of cranking, allow 2 minutes for the starting motor to cool.
5. If extra battery capacity is needed, refer to the Operator's Guide SEBU5516 - 955L, 977L & 983B Track Type Loaders.6. Refer to the Operator's Guide for after starting checks, warm up procedure and engine shutdown. For starting below 0°F (-18°C) the use of optional cold weather starting aids is recommended. A coolant heater, jacket water heater or extra battery capacity may be required.
The Starting Aid Ether Bottle must be removed before transporting the machine. See the Lubrication and Maintenance Guide SEBU5515 for removal and replacing the bottle.
Have questions with 105019-2910?
Group cross 105019-2910 ZEXEL
Isuzu
105019-2910
F 01G 29U 017