105964-0070 ZEXEL F 019 Z2E 592 BOSCH ELECTRIC GOVERNOR f019z2e592 1059640070 1157901160

Information electric governor

BOSCH F 019 Z2E 592 f019z2e592

ZEXEL 105964-0070 1059640070

ISUZU 1157901160 1157901160

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy ELECTRIC GOVERNOR 105964-0070 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1.	[1]	159560-3500	GOVERNOR HOUSING
2.	[6]	029010-6810	BLEEDER SCREW
3.	[1]	159636-1900	BLEEDER SCREW
4.	[1]	029621-7050	PACKING RING
5.	[1]	159564-1200	COILED SPRING
6.	[1]	159564-3600	SLOTTED WASHER
7.	[1]	159636-2720	CONNECTOR
8.	[1]	159584-9100	HEX-SOCKET-HEAD CAP SCREW
11.	[1]	159620-3921	ACTUATOR
11/1.	[1]	159562-3520	PLATE;GOV.
11/2.	[1]	159583-1020	STRAP
11/3.	[1]	159563-1700	LEVER SHAFT
11/4.	[2]	029311-0170	SHIM
11/5.	[2]	159635-0200	O-RING
11/6.	[2]	014011-0140	PLAIN WASHER D22&10.5T1.6
11/8.	[1]	016010-0940	LOCKING WASHER
11/9.	[1]	159635-8221	LINEAR DC MOTOR
11/10.	[4]	139006-9100	BLEEDER SCREW
11/11.	[1]	407914-1880	CONTROL UNIT
11/12.	[4]	010235-1640	HEX-SOCKET-HEAD CAP SCREW
11/14.	[4]	029300-5020	PLAIN WASHER D10&5.1T1.5
11/16.	[1]	159635-9300	GROMMET
11/18.	[2]	020105-1640	BLEEDER SCREW M5P0.8L16
11/19.	[1]	134002-0200	ADAPTOR
11/21.	[1]	159583-4220	CONTROL LEVER
11/22.	[1]	159563-2000	COILED SPRING
11/23.	[1]	159563-1800	BUSHING
11/24.	[1]	014110-8440	LOCKING WASHER
11/25.	[1]	013030-8140	UNION NUT M8P1.25H5
11/26.	[1]	159563-1000	FLAT-HEAD SCREW
11/27.	[2]	155615-1700	FLAT-HEAD SCREW
11/28.	[2]	029240-6010	UNION NUT M6P1.0H5*
11/30.	[1]	479765-2821	PULSE GENERATOR
11/31.	[1]	159635-0300	UNION NUT
11/32.	[2]	020106-1440	BLEEDER SCREW M6P1.0L14
11/38.	[1]	159635-5520	COVER
11/40.	[4]	159635-9800	BLEEDER SCREW
11/41.	[4]	014110-6440	LOCKING WASHER
12.	[2]	020106-4040	BLEEDER SCREW
13.	[1]	159561-1400	GOVERNOR COVER
14.	[6]	139006-1300	BLEEDER SCREW M6P1L76
15.	[1]	010006-5540	BLEEDER SCREW M6P1L55 4T
15B.	[1]	139006-2800	BLEEDER SCREW
16.	[9]	014110-6440	LOCKING WASHER
16.	[9]	014110-6440	LOCKING WASHER
16.	[9]	014110-6440	LOCKING WASHER
17.	[1]	154390-1300	GASKET
18.	[1]	159635-0100	GASKET
19.	[1]	154390-0500	GASKET
20.	[1]	154050-6120	STOPPING DEVICE
22.	[1]	159564-0800	EYE BOLT
23.	[2]	139514-0000	GASKET D19.2&14.2T1.0
25.	[1]	159636-2000	ADAPTOR
26.	[1]	014110-5440	LOCKING WASHER
30.	[1]	159586-3420	BRACKET
31.	[3]	020106-1240	BLEEDER SCREW M6P1.0L12
32.	[1]	159586-2600	CLAMPING BAND
33.	[2]	020106-1240	BLEEDER SCREW M6P1.0L12
50.	[1]	154064-0220	COVER
51.	[2]	020106-1640	BLEEDER SCREW M6P1.0L14
51B.	[1]	139006-9000	BLEEDER SCREW
51C.	[1]	020106-1840	BLEEDER SCREW M6P1L18
52.	[1]	029635-2020	O-RING
65.	[2]	159635-0400	BUSHING
80.	[1]	159586-6400	TOOTHED GEAR
81.	[1]	014111-2420	LOCKING WASHER
82.	[1]	013031-2120	UNION NUT
83.	[1]	025803-1610	WOODRUFF KEY

Include in #1:

101605-0160 as GOVERNOR

Cross reference number

Zexel num

Bosch num

Firm num

Name

105964-0070
105964-0071

F 019 Z2E 592

1157901160 ISUZU

ELECTRIC GOVERNOR
* K

Information:

Introduction
The following procedures contain crucial information on correctly installing the new 162-2501 Hose As and the 258-8917 Protection Sleeve .Note: The 162-2501 Hose As replaces 107-7942 Tube As .Installation Procedure of the Hose Assembly
Illustration 1 g01230674
Remove old 162-2501 Hose As (1). Keep all of the manifold and pump fittings attached.Note: Step 2 is only for 3408E engines.
Remove the 7W-6492 Pipe Plug (2) from the aftercooler housing (3). Install the 8T-6762 Pipe Plug into the aftercooler housing.
Illustration 2 g01230678
Note: Always tighten the fittings with your hand before you use a wrench. Support the hose and the elbow while you tighten in order to avoid the following damage: twisting, kinking and side loading.
Loosen elbow (4) and jam nut (5) .
Hand tighten the nut on the hose (5) to the elbow (4) .
Install the other end of the hose (6) to the pump fitting. Tighten the nut to 125 15 N m (90 11 lb ft).
Hold the elbow (4) in position and torque the jam nut to 145 15 N m (105 11 lb ft).
Support the elbow (4). Tighten the nut (5) on the hose to 125 15 N m (90 11 lb ft).
Illustration 3 g01230687
Illustration 3 shows the routing of the 162-2501 Hose As (8). The hose is routed from the rail, around the rear of the fuel transfer pump (9), and into the 90 degree fitting (7) that is installed into the pump.
Illustration 4 g01230689
Some 3408 engines use an aftercooler that is mounted high. The mounting bracket (10) is located close to the 162-2501 Hose As (8). If there is not enough clearance to install the protective sleeve, the hose will need to be loosened and the hose will need to be repositioned. Refer to 5 for repositioning of the hose.
Illustration 5 g01230690
The hose must be realigned if any of the following conditions exist:
Not enough clearance against the fuel transfer pump
Not enough clearance against the support bracket
Loosen the end of the hose (12) .
Loosen the elbow and the jam nut (11). Note: Do not remove the hose.
Reposition the hose in order to acquire the desired clearance.
Hold the end of the hose (12). Tighten the jam nut (11) .Tighten the jam nut to the following torque. ... 143 15 N m (105 11 lb ft)Note: Locking pliers can be used on the crimped portion of the hose. Do not use the locking pliers on the braided portion of the hose. This will damage the hose which will cause a failure.
Tighten the end of the hose (12) .Tighten the end of the hose to the following torque. ... 125 15 N m (92 11 lb ft)Note: If adjustment of the hose is required, make sure that the hose is not bent. Also, ensure that the hose is not twisted. If these conditions exist the PTFE liner can be damaged.Installation of the Protective Sleeve Over the New Hose Assembly
Illustration 6 g01106118
Top viewInstallation of a protective sleeve for the hoses of the