105962-0033 ZEXEL 9 420 614 805 BOSCH ELECTRIC GOVERNOR 9420614805 1059620033

Information electric governor

BOSCH 9 420 614 805 9420614805

ZEXEL 105962-0033 1059620033

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy ELECTRIC GOVERNOR 105962-0033 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1.	[1]	159560-2600	GOVERNOR HOUSING
2.	[8]	139006-4100	BLEEDER SCREW
4.	[1]	159635-8500	COILED SPRING
5.	[1]	159564-4000	SLOTTED WASHER
6.	[1]	159564-4100	SLOTTED WASHER
7.	[1]	159635-0022	CONNECTOR
7.	[1]	159636-3221	CONNECTOR
7B.	[1]	159635-6522	CONNECTOR
7B.	[1]	159636-3421	CONNECTOR
7C.	[1]	159635-6622	CONNECTOR
7C.	[1]	159636-3621	CONNECTOR
8.	[1]	020105-1240	BLEEDER SCREW M5P0.8L12
11.	[1]	159620-0721	ACTUATOR
11/1.	[1]	159562-2920	PLATE;GOV.
11/2.	[1]	159583-1020	STRAP
11/3.	[1]	159563-1700	LEVER SHAFT
11/4.	[2]	029311-0170	SHIM
11/4.	[2]	029311-0170	SHIM
11/5.	[2]	159635-0200	O-RING
11/5.	[2]	159635-0200	O-RING
11/6.	[2]	014011-0140	PLAIN WASHER D22&10.5T1.6
11/6.	[2]	014011-0140	PLAIN WASHER D22&10.5T1.6
11/8.	[1]	016010-0940	LOCKING WASHER
11/9.	[1]	159635-8221	LINEAR DC MOTOR
11/10.	[4]	139006-9100	BLEEDER SCREW
11/11.	[1]	407914-1880	CONTROL UNIT
11/12.	[4]	010235-1640	HEX-SOCKET-HEAD CAP SCREW
11/14.	[4]	029300-5020	PLAIN WASHER D10&5.1T1.5
11/15.	[1]	159636-0500	LIP
11/16.	[1]	159635-9300	GROMMET
11/17.	[1]	159630-0621	CABLE SET
11/18.	[2]	020105-1640	BLEEDER SCREW M5P0.8L16
11/21.	[1]	159583-3000	CONTROL LEVER
11/22.	[1]	159563-2000	COILED SPRING
11/23.	[1]	159563-1800	BUSHING
11/24.	[1]	014110-8440	LOCKING WASHER
11/25.	[1]	013030-8140	UNION NUT M8P1.25H5
11/26.	[1]	159563-1000	FLAT-HEAD SCREW
11/27.	[2]	155615-1700	FLAT-HEAD SCREW
11/27.	[2]	155615-1700	FLAT-HEAD SCREW
11/28.	[2]	029240-6010	UNION NUT M6P1.0H5*
11/28.	[2]	029240-6010	UNION NUT M6P1.0H5*
11/29.	[1]	159635-5400	BRACKET
11/30.	[1]	479765-6820	PULSE GENERATOR
11/31.	[1]	159635-0300	UNION NUT
11/32.	[2]	020106-1440	BLEEDER SCREW M6P1.0L14
11/38.	[1]	159635-5520	COVER
11/39.	[2]	159635-5200	SEAL RING
11/39.	[2]	159635-5200	SEAL RING
11/40.	[4]	020106-2840	BLEEDER SCREW
12.	[2]	020106-4040	BLEEDER SCREW
13.	[1]	159561-1520	GOVERNOR COVER
14.	[6]	139006-9400	BLEEDER SCREW
15.	[2]	139006-9200	BLEEDER SCREW
16.	[8]	014110-6440	LOCKING WASHER
17.	[1]	159584-7600	GASKET
18.	[1]	159635-0100	GASKET
19.	[1]	154390-0500	GASKET
20.	[1]	153021-6300	CAP
21.	[1]	026524-3040	GASKET
22.	[1]	029731-4680	EYE BOLT
23.	[2]	139514-0300	GASKET
65.	[2]	159635-0400	BUSHING
80.	[1]	159564-8600	TOOTHED GEAR
81.	[1]	014111-2420	LOCKING WASHER
82.	[1]	013031-2120	UNION NUT
83.	[1]	025803-1310	WOODRUFF KEY
90.	[1]	159400-2921	BRACKET
91.	[3]	156633-4700	BLEEDER SCREW
93.	[1]	159586-1620	BRACKET
94.	[2]	020118-1440	BLEEDER SCREW
804S.	[1]	159911-5020	PLUG HOUSING
805S.	[1]	159911-5120	PLUG HOUSING

Include in #1:

107691-3353 as GOVERNOR

107691-3354

Cross reference number

Zexel num

Bosch num

Firm num

Name

105962-0033

9 420 614 805

ELECTRIC GOVERNOR
K 14JE ELECTRIC GOVERNOR GOV

Information:

Introduction
This Special Instruction provides information in order to prolong the life of the cutting bits on the PM-465 rotor. An additional spray nozzle was added to the left side of the chamber.Rework Procedure
Table 1
Required Parts
Quantity Part Number Description
1 211-8607 Tube
1 211-8604 Plate
1 1G-6699 Adapter
1 1G-8270 Nozzle Body
2 5D-1026 Hose Clamp
1000 mm (39 inch) 5P-1690 Hose
1 081-2963 Cap
1 081-2965 Seal
1 115-9969 Male Connector
1 115-9970 Male Connector
1 212-0911 Nozzle
Illustration 1 g00853436
(A) 573 mm (22.56 inches) (B) 102.5 mm (4 inches) (C) 150 mm (5.91 inches)
Remove 142-7461 Plate (1) from the chamber.
Relocate the 142-7461 Plate (1) .
The new location of the 142-7461 Plate (1) should measure 150 mm (5.91 inches) (C) from the top of the chamber. The center of the 142-7461 Plate should remain at 573 mm (22.56 inches) (A) .
Cut a slot in the left side of the chamber that is 40 mm (1.57 inch) by 85 mm (3.35 inch). The center of the slot should measure 102.5 mm (4 inches) from the top (B) of the chamber and 573 mm (22.56 inches) from the front (A) of the chamber. Refer to Illustration 1.
Illustration 2 g00853889
Weld the 211-8604 Plate (2) in the slot. The plate should be flush with the inside of the chamber. Face the open end of the plate downward in the slot.
Illustration 3 g00853468
Illustration 4 g00853890
(D) 20 mm (0.79 inch) (E) 8.5 mm (0.33 inch)
Weld a 211-8607 Tube (3) onto the side of the chamber. Position the bottom of the tube 20 mm (0.79 inch) (D) from the bottom of the slot and 8.5 mm (0.33 inch) (E) to the right of the slot. Refer to Illustration 4.
Illustration 5 g00853470
Remove hose assembly (4) from the nozzle (5) that is located near the left side of the chamber.
Replace connector (6) with 115-9970 Male Connector .
Illustration 6 g00863254
Use the following parts in order to assemble a new nozzle: 115-9969 Male Connector (7), 1G-6699 Adapter (8), 1G-8270 Nozzle Body (9), 212-0911 Nozzle (10), 081-2965 Seal (11) and 081-2963 Cap (12) .
Illustration 7 g00853509
Place the new nozzle assembly in tube (13) that is located on the side of the chamber.Note: The flat spray pattern of the nozzle should be parallel to the slot.
Connect the two nozzles with a 5P-1690 Hose . Use two 5D-1026 Hose Clamps in order to secure the hose to the nozzles.