Information injector assy, pie
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
MJUYHT Piezo Injector 295900-0110, 295900-0020, 23670-26020, 23670-26011, 23670-29105, 23670-29055, 23670-0R040, 23670-0R041
MJUYHT Accurately transport fuel into the cylinder block || And spray it into the branch pipe for full combustion || Reduce emissions and fuel consumption, with good fuel atomization and mixed combustion || 295900-0110, 295900-0020 High pressure injection: capable of injecting fuel at higher pressures to improve combustion efficiency. || The fuel injector is rust resistant and waterproof to support better throttle response and more effective fuel atomization
MJUYHT Accurately transport fuel into the cylinder block || And spray it into the branch pipe for full combustion || Reduce emissions and fuel consumption, with good fuel atomization and mixed combustion || 295900-0110, 295900-0020 High pressure injection: capable of injecting fuel at higher pressures to improve combustion efficiency. || The fuel injector is rust resistant and waterproof to support better throttle response and more effective fuel atomization
$1,318.68
02 May 2023
0.0022[0.00] Pounds
CN: 5647896
Fuel Injector 23670-26011 295900-0110 23670-26020 Compatible With Diesel Engine
JUIXXE Easy to install and adjust. || Made of high-quality materials. || Direct replacement of stock parts || Special technology to ensure long service life. || Built according to strict quality control standards.
JUIXXE Easy to install and adjust. || Made of high-quality materials. || Direct replacement of stock parts || Special technology to ensure long service life. || Built according to strict quality control standards.
$619.90
12 Oct 2022
CN: PANGOLIN Store
PANGOLIN 295900-0110 23670-0R040 9729590-011 23670-26011 Fuel Injector Common Rail Injector for LEXUS 2.2 D-CAT DCRI20110 Aftermarket Parts, 3 Month Warranty
PANGOLIN PART NUMBER: 295900-0110 / 295900-0130 / 295900-0030, 2959000110 / 2959000130 / 2959000030, 295900-0100 / 295900-0010 / 23670-0R041, 2959000100 / 2959000010 / 236700R041, 23670-0R042 36700R040 236700R041 2367029055, 2367026011 23670-29105 2367026020 2367029105, 23670-29055 / 23670-26020 / 23670-26011, 2367029055 / 2367026020 / 2367026011, 23670-0R040, 23670 0R040 DCRI200110 9729590-011 || FEATURES: Lower flow fluctuations for precise fuel control; Advanced equipment and strict factory inspection, using high-performance engineering materials, excellent workmanship. || APPLICATION: 295900-0110 23670-0R040 9729590-011 23670-26011 Fuel Injector Common Rail Injector for LEXUS 2.2 D-CAT DCRI20110 Aftermarket Parts || FAST DELIVERY: Your order (US CA AU) will be shipped by Air Freight Channel within 24-72 hours after payment received and will arrive in 3-7 days. || CUSTOMER SERVICE: 7/24 all day Service; A truly worry-free shopping experience; 3 Month Warranty, every product fully tested before the shipment, we offer free repair or change or return service if there is any quality problem of the product we sent to you during the warranty.
PANGOLIN PART NUMBER: 295900-0110 / 295900-0130 / 295900-0030, 2959000110 / 2959000130 / 2959000030, 295900-0100 / 295900-0010 / 23670-0R041, 2959000100 / 2959000010 / 236700R041, 23670-0R042 36700R040 236700R041 2367029055, 2367026011 23670-29105 2367026020 2367029105, 23670-29055 / 23670-26020 / 23670-26011, 2367029055 / 2367026020 / 2367026011, 23670-0R040, 23670 0R040 DCRI200110 9729590-011 || FEATURES: Lower flow fluctuations for precise fuel control; Advanced equipment and strict factory inspection, using high-performance engineering materials, excellent workmanship. || APPLICATION: 295900-0110 23670-0R040 9729590-011 23670-26011 Fuel Injector Common Rail Injector for LEXUS 2.2 D-CAT DCRI20110 Aftermarket Parts || FAST DELIVERY: Your order (US CA AU) will be shipped by Air Freight Channel within 24-72 hours after payment received and will arrive in 3-7 days. || CUSTOMER SERVICE: 7/24 all day Service; A truly worry-free shopping experience; 3 Month Warranty, every product fully tested before the shipment, we offer free repair or change or return service if there is any quality problem of the product we sent to you during the warranty.
Components :
| 001. | INJECTOR ASSY, PIE | 29590-00110 |
| 002. | INJECTOR ASSY, PIE | 29590-00100 |
Scheme ###:
| 000. | [01] | 29590-00110 | INJECTOR ASSY, PIE | 23670-29105 |
| 001. | [01] | 29590-00100 | INJECTOR ASSY, PIE | 23670-26020 |
| 002. | [01] | 09313-30810 | GASKET | 11176-26010 |
Include in #3:
29590-00110
as INJECTOR ASSY, PIE
Cross reference number
| Part num | Firm num | Firm | Name |
| 29590-00110 | 23670-2910 | INJECTOR ASSY, PIE | |
| 23670-29105 | TOYOTA | INJECTOR ASSY |
Information:
Walk-Around Inspection
Inspect Engine for Leaks and Loose Connections
For maximum service life of your truck engine, make a thorough under the hood inspection before starting the engine. Look for such items as oil or coolant leaks, loose bolts, worn fan belts, loose connections and trash build-up. Remove trash build-up and have repairs made as needed.Check the fluid levels more frequently than the recommended maintenance intervals and continue to monitor fluid levels until any leak is found and fixed.* Wipe all fittings, caps and plugs before performing maintenance to reduce the chance of system contamination. Inspect:* Radiator and ATAAC core for leaks and trash build-up.* Radiator and ATAAC air intake system hoses and elbows for cracks and loose clamps.* Fan and accessory drive belts for cracks, breaks or other damage.Belts for multiple groove pulleys must be replaced as matched sets. If only one belt of a two or three belt set is replaced, it will carry more of a load than the belts not replaced since the older belts are stretched. The additional load on the new belt could cause it to break. Inspect:* Water pump for coolant leaks. The water pump seal is lubricated by coolant in the cooling system. It is normal for a small amount of leakage to occur as the engine cools down and parts contract. If leaks are found, check the coolant level frequently and continue to monitor the level until the water pump is repaired. Excessive coolant leakage may indicate the need to replace the water pump seal.For removal and installation of water pumps and/or seals, see the Service Manual for this engine or consult your Caterpillar dealer. Inspect:* Lube system for leaks, such as front and rear crankshaft seals, oil pan, oil filters and valve covers.* Fuel system for leaks, loose fuel line clamps and fittings and loose or worn hoses.
Fuel line clamps should not be over torqued. Over torqueing causes the clamps to butterfly, which results in low clamping force and fuel line vibration and eventual failure.
Tighten fuel line clamps as required using 6V4980 Torque Screwdriver Tool Group. The standard torque for these fasteners (#10 screw) is 20 lb inch (2.26 N m).* Inspect wiring and wiring harnesses for loose connections and worn or frayed wires. Inspect:* Air intake system hoses and elbows for cracks and loose clamps. * ECM to cylinder head ground strap and starter negative cable for good connection and condition.All guards must be in place. Repair or replace missing or damaged guards.Check condition of batteries and the level of electrolyte, unless equipped with a maintenance free battery.Refer to OEM truck owner manual or manufacturers' recommendations for battery maintenance.
Inspect Engine for Leaks and Loose Connections
For maximum service life of your truck engine, make a thorough under the hood inspection before starting the engine. Look for such items as oil or coolant leaks, loose bolts, worn fan belts, loose connections and trash build-up. Remove trash build-up and have repairs made as needed.Check the fluid levels more frequently than the recommended maintenance intervals and continue to monitor fluid levels until any leak is found and fixed.* Wipe all fittings, caps and plugs before performing maintenance to reduce the chance of system contamination. Inspect:* Radiator and ATAAC core for leaks and trash build-up.* Radiator and ATAAC air intake system hoses and elbows for cracks and loose clamps.* Fan and accessory drive belts for cracks, breaks or other damage.Belts for multiple groove pulleys must be replaced as matched sets. If only one belt of a two or three belt set is replaced, it will carry more of a load than the belts not replaced since the older belts are stretched. The additional load on the new belt could cause it to break. Inspect:* Water pump for coolant leaks. The water pump seal is lubricated by coolant in the cooling system. It is normal for a small amount of leakage to occur as the engine cools down and parts contract. If leaks are found, check the coolant level frequently and continue to monitor the level until the water pump is repaired. Excessive coolant leakage may indicate the need to replace the water pump seal.For removal and installation of water pumps and/or seals, see the Service Manual for this engine or consult your Caterpillar dealer. Inspect:* Lube system for leaks, such as front and rear crankshaft seals, oil pan, oil filters and valve covers.* Fuel system for leaks, loose fuel line clamps and fittings and loose or worn hoses.
Fuel line clamps should not be over torqued. Over torqueing causes the clamps to butterfly, which results in low clamping force and fuel line vibration and eventual failure.
Tighten fuel line clamps as required using 6V4980 Torque Screwdriver Tool Group. The standard torque for these fasteners (#10 screw) is 20 lb inch (2.26 N m).* Inspect wiring and wiring harnesses for loose connections and worn or frayed wires. Inspect:* Air intake system hoses and elbows for cracks and loose clamps. * ECM to cylinder head ground strap and starter negative cable for good connection and condition.All guards must be in place. Repair or replace missing or damaged guards.Check condition of batteries and the level of electrolyte, unless equipped with a maintenance free battery.Refer to OEM truck owner manual or manufacturers' recommendations for battery maintenance.