Information valve assy, suctio
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Suction Control Valve SCV 294200-0670 2942000670 Diesel Fuel injector Pump Regulator
xinDieseltt Symptoms of a failing SCV include inconsistent rail pressure readings, rough engine idle, increased fuel consumption, and potential stalling || Replacement Part Number:294200-0670 2942000670 Check whether the part number is correct to avoid installing incorrect parts. || Our suction control valve comes with six-month warranty || Every SCV valve is rigorously tested and verified. || If you are unsure if it will fit your vehicle or have problems with installation, please contact our customer service staff to assist you.
xinDieseltt Symptoms of a failing SCV include inconsistent rail pressure readings, rough engine idle, increased fuel consumption, and potential stalling || Replacement Part Number:294200-0670 2942000670 Check whether the part number is correct to avoid installing incorrect parts. || Our suction control valve comes with six-month warranty || Every SCV valve is rigorously tested and verified. || If you are unsure if it will fit your vehicle or have problems with installation, please contact our customer service staff to assist you.
VIIKEND Suction Control Valve 8-98181831-0 294200-0670 Compatible with Isuzu Engine 6HK1 Compatible with Hitachi Excavator ZW220 ZW250 ZX330 ZX350 ZW220-HCMF ZW250-HCMF
VIIKEND Part Name: Suction Control Valve || Part Number: 8-98181831-0 294200-0670 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: 6HK1 || Applicable: Compatible with Isuzu Engine 6HK1 || Compatible with Hitachi Excavator ZW220 ZW250 ZX330 ZX350 ZW220-HCMF ZW250-HCMF ZX350-3-AMS
VIIKEND Part Name: Suction Control Valve || Part Number: 8-98181831-0 294200-0670 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: 6HK1 || Applicable: Compatible with Isuzu Engine 6HK1 || Compatible with Hitachi Excavator ZW220 ZW250 ZX330 ZX350 ZW220-HCMF ZW250-HCMF ZX350-3-AMS
You can express buy:
USD 56.59
14-06-2025
14-06-2025
A30F-Fuel Pump Suction Control Valve SCV 294200-0670 For ISUZU 6HK 8981305080 898181830 Pressure Regulator Valve 294200-367
USD 45.75
14-06-2025
14-06-2025
Engine Fuel Suction Control SCV Valve 294200-0670 for Isuzu 6HK Hino J08 Nissan
USD 62.23
26-05-2025
26-05-2025
Fuel Pump Suction Control Valve SCV 294200-0670 for ISUZU 6HK 8981305080 898181830 Pressure Regulator Valve 294200-367
Images:
USD 30.18
[19-May-2025]
USD 46.38
[19-May-2025]
USD 55
[13-May-2025]
USD 45
[13-May-2025]
Include in #3:
Cross reference number
| Part num | Firm num | Firm | Name |
| 29420-00670 | VALVE ASSY, SUCTIO |
Information:
Start By:a. remove timing gear coverb. remove fuel injection pump housing and rack actuator package 1. Remove four bolts (2), plate (3) and idler gear (1). 2. If the camshaft is not going to be removed, use tooling (A) to remove camshaft gear (4).
Do not turn the crankshaft with the camshaft gear removed. Damage can be caused to the pistons and valves, or both.
3. Remove bolts (5) that hold timing gear plate (6) to the cylinder block.4. Remove timing gear plate (6). 5. Use tooling (B) to remove the bearing from the idler gear. The following steps are for the installation of the timing gears and plate.6. Install a new gasket on the timing gear plate.7. Put timing gear plate (6) in position on the cylinder block, and install the bolts that hold the timing gear plate to the cylinder block.8. Heat camshaft gear (4) to a maximum temperature of 315° C (600° F), and install it on the camshaft.9. Use tooling (B), and install the bearing in the idler gear. Set the gear on the front face, (face with timing marks). Drive the bearing from the rear face toward the front face of the gear. Install the bearing to a depth of 1.5 0.5 mm (.06 .02 in.) below the rear face of the idler gear.10. Install the idler gear, plate and bolts. Be sure No. 1 cylinder is at top center on the compression stroke. Install the idler gear so "V" mark (7) on the idler gear is in alignment with the "V" mark on the crankshaft gear. "K" marks (8) of the camshaft gear can be seen at the outer edges of the idler gear.End By:a. install fuel injection pump housing and rack actuator packageb. install timing gear cover
Do not turn the crankshaft with the camshaft gear removed. Damage can be caused to the pistons and valves, or both.
3. Remove bolts (5) that hold timing gear plate (6) to the cylinder block.4. Remove timing gear plate (6). 5. Use tooling (B) to remove the bearing from the idler gear. The following steps are for the installation of the timing gears and plate.6. Install a new gasket on the timing gear plate.7. Put timing gear plate (6) in position on the cylinder block, and install the bolts that hold the timing gear plate to the cylinder block.8. Heat camshaft gear (4) to a maximum temperature of 315° C (600° F), and install it on the camshaft.9. Use tooling (B), and install the bearing in the idler gear. Set the gear on the front face, (face with timing marks). Drive the bearing from the rear face toward the front face of the gear. Install the bearing to a depth of 1.5 0.5 mm (.06 .02 in.) below the rear face of the idler gear.10. Install the idler gear, plate and bolts. Be sure No. 1 cylinder is at top center on the compression stroke. Install the idler gear so "V" mark (7) on the idler gear is in alignment with the "V" mark on the crankshaft gear. "K" marks (8) of the camshaft gear can be seen at the outer edges of the idler gear.End By:a. install fuel injection pump housing and rack actuator packageb. install timing gear cover