Information compensator sub-as
Rating:
Scheme ###:
| 000. | [01] | 19260-00090 | COMPENSATOR SUB-AS | 22430-1040 |
| 001. | [01] | 19261-10011 | HOUSING, BOOST COM | 22431-1020A |
| 002. | [01] | 19262-00050 | COVER SUB-ASSY | 22435-1020A |
| 003. | [01] | 19263-30010 | WASHER, THRUST | 22434-1030A |
| 004. | [01] | 19263-20010 | SEAT, SPRING, UPR | 22434-1020A |
| 005. | [01] | 19262-70010 | ROD, PUSH | 22432-1040A |
| 006. | [01] | 19263-50010 | BUSHING, GUIDE | 22375-1150A |
| 007. | [01] | 90160-06051 | NUT, HEXAGON | 22825-1480A |
| 008. | [01] | 19262-80020 | SCREW | 22432-1030A |
| 009. | [01] | 19263-40030 | SPRING, BOOST COMP | 22433-1030A |
| 010. | [01] | 19263-10010 | DIAPHRAGM | 22361-1050A |
| 012. | [01] | 94901-70490 | WASHER, WAVE | 22323-1180A |
| 013. | [02] | 94901-81020 | WASHER, COPPER PLA | 22867-1500A |
| 014. | [01] | 09103-10020 | NUT, CAP | 22342-1300A |
| 015. | [01] | 09116-60080 | SCREW, STOP | 22865-1220A |
| 016. | [01] | 94805-30130 | NUT, HEXAGON, W/HO | 22825-1060A |
| 019. | [01] | 09052-40041 | PLUG, SCREW | 22845-1300A |
| 020. | [01] | 94901-81040 | WASHER, COPPER PLA | 22843-1430A |
| 021. | [03] | 90107-06121 | BOLT, HEXAGON | 22815-2040A |
| 022. | [01] | 94904-50120 | BOLT, HEXAGON, W/ | 22815-2050A |
| 023. | [01] | 90170-06361 | NUT, HEXAGON | 92100-6040A |
Include in #3:
09130-00523
as COMPENSATOR SUB-AS
19260-00090
Cross reference number
| Part num | Firm num | Firm | Name |
| 19260-00090 | 22430-1040 | COMPENSATOR SUB-AS | |
| 22430-1040A | HINO | COMPENSATOR SUB-AS | |
| 22430-1040 | HINO | COMPENSATOR SUB-AS |
Information:
(8) Piston cooling orifice.
There are holes in the bores for the main bearings, between the cylinders for piston cooling orifices. These holes must have orifices (8) installed.
(9) Distance two dowels extend from the surface of the cylinder block ... 19.8 0.5 mm (.78 .02 in)(10) Distance hollow dowel extends from the surface of the cylinder block ... 16.0 0.5 mm (.63 .02 in)(11) Depth to install two dowels below the surface of the cylinder block (apply loctite #11358) ... 1.0 0.5 mm (.04 .02 in)(12) Distance dowels extend from the front face of the cylinder block ... 22.4 0.5 mm (.88 .02 in)(13) Distance stud extends from the front face of the cylinder block ... 15.7 0.5 mm (.62 .02 in)(14) Distance two dowels extend from the rear face of the cylinder block ... 12.7 0.5 mm (.50 .02 in)
There are holes in the bores for the main bearings, between the cylinders for piston cooling orifices. These holes must have orifices (8) installed.
(9) Distance two dowels extend from the surface of the cylinder block ... 19.8 0.5 mm (.78 .02 in)(10) Distance hollow dowel extends from the surface of the cylinder block ... 16.0 0.5 mm (.63 .02 in)(11) Depth to install two dowels below the surface of the cylinder block (apply loctite #11358) ... 1.0 0.5 mm (.04 .02 in)(12) Distance dowels extend from the front face of the cylinder block ... 22.4 0.5 mm (.88 .02 in)(13) Distance stud extends from the front face of the cylinder block ... 15.7 0.5 mm (.62 .02 in)(14) Distance two dowels extend from the rear face of the cylinder block ... 12.7 0.5 mm (.50 .02 in)