Information pump assy, injecti
Rating:
Components :
| 001. | PUMP ASSY, INJECTI | 19100-09771 |
| 001. | PUMP ASSY, INJECTI | 19100-09771 |
| 002. | BODY ASSY, INJECTI | 09010-09960 |
| 003. | GOVERNOR ASSY, MEC | 09130-04090 |
| 004. | COVER ASSY, GOVERN | 09145-00154 |
| 005. | TIMER ASSY, AUTOMA | 09180-01881 |
| 006. | PUMP ASSY, FUEL FE | 09210-01440 |
Scheme ###:
| 000. | [01] | 19100-09770 | PUMP ASSY, INJECTI | ME076452 |
| 000. | [01] | 19100-09771 | PUMP ASSY, INJECTI | ME076452 |
| 005. | [01] | 09010-09960 | BODY ASSY, INJECTI | ME736047 |
| 006. | [01] | 09130-04090 | GOVERNOR ASSY, MEC | ME736041 |
| 007. | [01] | 09001-80090 | COVER, CONTROL RAC | ME702251 |
| 008. | [01] | 94914-02840 | O-RING | MH035502 |
| 009. | [01] | 09006-00371 | COVER SUB-ASSY, TI | ME728195 |
| 010. | [01] | 09180-01881 | TIMER ASSY, AUTOMA | ME702010 |
| 011. | [04] | 94905-02680 | NUT, HEXAGON | ME702046 |
| 011. | [04] | 91266-10081 | NUT, HEXAGON | MF430122 |
| 012. | [04] | 90258-10001 | WASHER, SPRING | MC327716 |
| 013. | [02] | 94901-15020 | WASHER, STEEL PLAT | MH005068 |
| 014. | [01] | 09069-11320 | BRACKET, STOP WIRE | ME703775 |
| 015. | [01] | 94913-00210 | KEY, WOODRUFF | ME702047 |
| 016. | [01] | 94901-40210 | WASHER, COUNTERSUN | ME702043 |
| 017. | [01] | 09001-20290 | NUT, TIMER ROUND | ME702547 |
| 018. | [01] | 90801-40280 | O-RING | ME702918 |
| 019. | [01] | 09210-01440 | PUMP ASSY, FUEL FE | ME035928 |
| 020. | [01] | 09009-20100 | BRACKET | ME702036 |
| 021. | [01] | 94904-73910 | BOLT, W/WASHER | ME703449 |
| 022. | [05] | 94904-72690 | BOLT, W/WASHER | ME702045 |
| 023. | [01] | 91418-06201 | BOLT, W/WASHER | ME702041 |
| 024. | [01] | 09028-50021 | CAP | ME035845 |
| 025. | [01] | 09028-50050 | CAP | ME076458 |
Include in #3:
19100-09771
as PUMP ASSY, INJECTI
Cross reference number
| Part num | Firm num | Firm | Name |
| 19100-09771 | ME076452 | PUMP ASSY, INJECTI |
Information:
(8) Piston cooling orifice.
There are holes in the bores for the main bearings, between the cylinders for piston cooler orifices. These holes must have orifices (8) installed.
(9) Distance two dowels extend from the surface of the cylinder block ... 19.8 0.5 mm (.78 .02 in.)(10) Distance hollow dowel extends from the surface of the cylinder block ... 16.0 0.5 mm (.63 .02 in.)(11) Depth to install two dowels below the surface of the cylinder block (apply loctite #11358) ... 1.0 0.5 mm (.04 .02 in.)(12) Distance dowels extend from the front face of the cylinder block ... 22.4 0.5 mm (.88 .02 in.)(13) Distance stud extends from the front face of the cylinder block ... 15.7 0.5 mm (.62 .02 in.)(14) Distance two dowels extend from the rear face of the cylinder block ... 12.7 0.5 mm (.50 .02 in.)
There are holes in the bores for the main bearings, between the cylinders for piston cooler orifices. These holes must have orifices (8) installed.
(9) Distance two dowels extend from the surface of the cylinder block ... 19.8 0.5 mm (.78 .02 in.)(10) Distance hollow dowel extends from the surface of the cylinder block ... 16.0 0.5 mm (.63 .02 in.)(11) Depth to install two dowels below the surface of the cylinder block (apply loctite #11358) ... 1.0 0.5 mm (.04 .02 in.)(12) Distance dowels extend from the front face of the cylinder block ... 22.4 0.5 mm (.88 .02 in.)(13) Distance stud extends from the front face of the cylinder block ... 15.7 0.5 mm (.62 .02 in.)(14) Distance two dowels extend from the rear face of the cylinder block ... 12.7 0.5 mm (.50 .02 in.)