19100-05760 PUMP ASSY, INJECTI Denso Cross

Details of Maximum Gross Ratings
4.2482 Engines
General ... 60 kW (80 bhp) at 2,600 rev/minMaximum Torque ... 265 Nm (195 lbf ft) at 1,400 rev/minHeavy Duty ... 54 kW (72.5 bhp) at 2,600 rev/minMaximum Torque ... 238 Nm (176 lbf ft) at 1,400 rev/min4.248 Engines
General Agricultural and Industrial ... 62 kW (84 bhp) at 2500 rev/minMaximum Torque ... 263 Nm (194 lbf ft) at 1400 rev/minHeavy Duty Agricultural and Industrial ... 58 kW (78.5 bhp) at 2200 rev/minMaximum Torque ... 279 Nm (206 lbf ft) at 1400 rev/minT4.236 Engines
General ... 76 kw (102 bhp) at 2,600 rev/minMaximum Torque ... 337 Nm (250 lbf ft) at 1,600 rev/minHeavy Duty ... 67 kW (90 bhp) at 2,500 rev/minMaximum Torque ... 324 Nm (240 lbf ft) at 1,400 rev/min4.236 Engines
Vehicle ... 61 kW (82 bhp) at 2800 rev/minMaximum Torque ... 256 Nm (194 lbf ft) at 1450 rev/minGeneral Agricultural and Industrial ... 60 kW 81 bhp at 2600 rev/minMaximum Torque ... 267 Nm (197 lbf ft) at 1350 rev/minHeavy Duty Agricultural and Industrial ... 54 kW (72 bhp) at 2200 rev/minMaximum Torque ... 272 Nm (201 lbf ft) at 1400 rev/min4.212 Engines
Agricultural ... 46 kW (62 bhp) at 2200 rev/minMaximum Torque ... 229 Nm (169 lbf ft) at 1350 rev/minEngine Weights
Typical dry weight ... 590 lb(269 kg)Typical installed weight ... 750/900 lb(340/409 kg)All the above ratings are maximum and can vary according to application. For details of individual ratings, apply to your nearest Perkins Distributor.De-Rating for Altitude
Where engines operate at high altitudes they should be de-rated. The following table is given as a general guide for naturally aspirated engines to be applied on a percentage basis, where specific figures for a particular engine rating are not available. Any necessary adjustments in this respect to the fuel pump should be carried out by the C.A.V. dealer for the territory concerned.For turbocharged engines and any further information apply to Perkins Engines Ltd., Peterborough, or to Overseas Companies listed on Page 2.Recommended Torque Tensions
The following figures will apply with the components lightly oiled before assembly. Service Wear Limits
The following "wear limits" indicate the condition when it is recommended that the respective items should be serviced or replaced.Cylinder Head Bow Transverse ... 0.003 in(0,08 mm)Longitudinal ... 0.006 in(0,15 mm)Maximum Bore Wear (when reboring or new liners are necessary) ... 0.008 in(0,2 mm)Crankshaft Main and Big End Journal Wear, Ovality ... 0.0015 in(0,04 mm)Maximum Crankshaft End Float ... 0.015 in(0,38 mm)Valve Stem to Bore/Guide Clearance inlet ... 0.005 in(0,13 mm)exhaust ... 0.006 in(0,15 mm)Valve Head Thickness between run-out of valve seat and face of valve ... 1/32 in(0,79 mm)Rocker Clearance on Rocker Shaft ... 0.005 in(0,13 mm)Camshaft Journals-Ovality and Wear ... 0.002 in(0,05 mm)Camshaft End Float ... 0.020 in(0,51 mm)Idler Gear End Float ... 0.010 in(0,25 mm)*Valve Head Depth below Cylinder Head Face exhaust (Earlier) ... 0.055 in(1,40 mm) maximum*Valve Head Depth below Cylinder Head Face (Current) ... 0.073 in(1,85 mm) maximum*Valve Head Depth below Cylinder Head Face inlet ... 0.061 in(1,55 mm) maximum*Where it is necessary