19000-08770 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935002370
19000-08770 PUMP ASSY, INJECTI
Rating:
6
Buy PUMP ASSY, INJECTI 19000-08770 genuine, new aftermarket engine parts with delivery

KIT List:

Body assy, injecti 1904400300
Timer assy, automa 0918030050
Pump assy, fuel fe 1922900060

Components :

001. PUMP ASSY, INJECTI 19000-08770
002. BODY ASSY, INJECTI 09010-04800
003. TIMER ASSY, AUTOMA 09180-01360
004. PUMP ASSY, FUEL FE 09210-01101
004. PUMP ASSY, FUEL FE 09210-01101

Scheme ###:

000. [01] 19000-08770 PUMP ASSY, INJECTI 22100-58021-1
003. [01] 09001-80061 COVER, CONTROL RAC 22116-46010
004. [01] 09010-04800 BODY ASSY, INJECTI 22120-58011
005. [01] 09070-00500 GOVERNOR ASSY, COM 22320-58350
006. [01] 09210-01101 PUMP ASSY, FUEL FE 22510-56040
009. [01] 09001-20020 NUT, TIMER ROUND 22611-46010
010. [01] 94901-50490 WASHER, SPRING 22173-46010
011. [01] 09257-50020 SHAFT, SPLINE 22174-47010
012. [01] 94913-00050 KEY, WOODRUFF 90099-13002
013. [01] 91518-08221 BOLT, W/WASHER 90091-20804
014. [03] 94904-70620 BOLT, W/WASHER 90099-04526
015. [01] 91418-06121 BOLT, W/WASHER 90091-20607
100. [01] 09180-01360 TIMER ASSY, AUTOMA 22610-56040

Include in #3:

19000-08770 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
19000-08770  22100-5802  PUMP ASSY, INJECTI
22100-58021-1    TOYOTA PUMP ASSY, INJECTI




Information:

General Hazard Information
Attach a DO NOT OPERATE or similar warning tag to start switch or controls before performing maintenance or repairing the engine. These tags, SEHS7332, are available from your Caterpillar dealer. When appropriate, attach tags at the engine and at each start position and disconnect starting controls.Do not allow unauthorized personnel on or around the engine when it is being serviced.Diesel engine exhaust contains products of combustion which may be harmful to your health. Always start and operate the engine in a well ventilated area and, if in an enclosed area, vent the exhaust to the outside.Use caution when removing cover plates. Gradually loosen (do not remove) the last two bolts or nuts located at opposite ends of the cover or device. Pry cover loose to relieve any spring or other pressure, before removing the last bolts or nuts.Use caution when removing vent release valve, grease fittings, pressure taps, breathers or drain plugs. Hold a rag over the cap or plug to prevent being sprayed or splashed by liquids under pressure.* Wear a hard hat, protective glasses, hearing protection and other protective equipment as required by job conditions.* Do not wear loose clothing or jewelry that can catch on controls or other parts of the engine.* Make certain all protective guards and covers are secured in place.* Use all cleaning solutions with care.* Never put maintenance fluids into glass containers since glass containers can break.* Report all needed repairs.* Stop the engine.* Do not attempt any repairs or adjustments to the engine or driven equipment while it is running.* Do not attempt repairs you do not understand.* Ensure the protective locks or controls are in the applied position.* Be sure the remote starting system is inoperative on the equipment being serviced. Always disconnect the engine starter circuit when working on the generator. Place the automatic start-stop switch to the STOP position before working on the equipment to prevent accidental starting.* Disconnect the batteries whenever performing any maintenance or before servicing the electrical system. If the engine has electric starters, disconnect and tape the battery ground leads to prevent accidental starting.* Use proper tools; replace or repair broken or damaged equipment.* When starting an engine after repairs have been made to the fuel system or governor, make provisions for shutting off the engine's intake air and/or fuel supply (to stop the engine), in case there is an overspeed on start-up.Pressure Air and Water
Pressure air can cause personal injury. When using pressure air for cleaning, wear a protective face shield, protective clothing and protective shoes.The maximum air pressure must be below 200 kPa (30 psi) for cleaning purposes.Wear eye protection at all times when cleaning the cooling system. Pressurized water could cause debris and/or hot water to be blown and result in personal injury.Fluid Penetration
Always use a board or cardboard when checking for a leak. Escaping fluid under pressure, even a pin-hole size leak, can penetrate body tissue, causing serious injury or possible death.If fluid is injected into your

Have questions with 19000-08770?





Group cross 19000-08770

Back to top