Information pump assy, injecti
Nozzle:
0935002010
Rating:
KIT List:
| Body assy, injecti | 1904400300 |
| Governor assy, inj | 1908900260 |
| Timer assy, automa | 0918030050 |
| Pump assy, fuel fe | 1922900060 |
Components :
| 001. | PUMP ASSY, INJECTI | 19000-05000 |
| 002. | BODY ASSY, INJECTI | 09010-04060 |
| 003. | GOVERNOR ASSY, INJ | 09050-00960 |
| 004. | TIMER ASSY, AUTOMA | 09180-01260 |
| 005. | PUMP ASSY, FUEL FE | 09210-01071 |
Scheme ###:
| 000. | [01] | 19000-05000 | PUMP ASSY, INJECTI | 22100-87361-000 |
| 001. | [01] | 09010-04060 | BODY ASSY, INJECTI | 22120-87307-000 |
| 002. | [01] | 09050-00960 | GOVERNOR ASSY, INJ | 22310-87306-000 |
| 003. | [01] | 09210-01071 | PUMP ASSY, FUEL FE | 22510-87308-000 |
| 006. | [01] | 94913-00190 | KEY, WOODRUFF | 90099-13002-000 |
| 007. | [01] | 94901-50500 | WASHER, SPRING | 22173-87301-000 |
| 008. | [01] | 09001-20260 | NUT, TIMER ROUND | 22611-68010-000 |
| 009. | [01] | 91518-08221 | BOLT, W/WASHER | 90091-20804-000 |
| 010. | [04] | 91518-06161 | BOLT, W/WASHER | 22128-87702-000 |
| 011. | [01] | 09001-80010 | COVER, CONTROL RAC | 22116-77020-000 |
| 100. | [01] | 09180-01260 | TIMER ASSY, AUTOMA | 22610-87307-000 |
Include in #3:
19000-05000
as PUMP ASSY, INJECTI
Cross reference number
| Part num | Firm num | Firm | Name |
| 19000-05000 | 22100-8736 | PUMP ASSY, INJECTI | |
| 22100-87361-000 | DAIHATSU | PUMP ASSY, INJECTI |
Information:
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove cover (1) and the O-ring seal from the riming gear plate.
Use care when the trunnion is removed to prevent damage to the crankshaft front seal
2. Remove three bolts (2), trunnion (3) and the O-ring seal. 3. Remove the bolts that hold the timing gear cover in place. Carefully loosen the cover from the dowels and remove cover (4).4. Clean the old gasket from the contact surface of the timing gear cover and the timing gear plate.Install Timing Gear Cover
1. Install a new gasket (1) on the timing gear plate. Cut the gasket even with the bottom face on the cylinder block. 2. Install the timing gear cover (2). The bolts in locations (3) and (4) are tightened to a torque of 23 4 N m (17 3 lb ft). 3. Be sure the O-ring seal (6) is on position on trunnion. Install trunnion (5) and the bolts. Tighten the bolts to a torque of 135 15 N m (100 11 lb ft). 4. Install the O-ring seal and cover (7).End By:a. install crankshaft damper and pulleyb. install water pumpc. install air compressord. install oil pan