19000-04402 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

19000-04402 PUMP ASSY, INJECTI
Rating:
8
Buy PUMP ASSY, INJECTI 19000-04402 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 19000-04402
002. BODY ASSY, INJECTI 09010-02802
003. GOVERNOR ASSY, MEC 09080-06241
004. PUMP ASSY, FUEL FE 09210-01011

Scheme ###:

000. [01] 19000-04402 PUMP ASSY, INJECTI 34461-11012
005. [01] 09010-02802 BODY ASSY, INJECTI 34461-00100
006. [01] 09080-06241 GOVERNOR ASSY, MEC
007. [01] 09001-80220 COVER, CONTROL RAC
008. [01] 94905-02450 NUT, HEXAGON 94905-02450
009. [01] 94913-00190 KEY, WOODRUFF 94913-00190
010. [01] 94901-50500 WASHER, SPRING 94901-50500
012. [01] 09210-01011 PUMP ASSY, FUEL FE 34461-00303
013. [01] 91518-08221 BOLT, W/WASHER 91518-08221
014. [05] 91418-06161 BOLT, W/WASHER 91418-06161
015. [01] 91518-06121 BOLT, W/WASHER 91518-06121

Include in #3:

19000-04402 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
19000-04402  34461-1101  PUMP ASSY, INJECTI




Information:

Start By:a. remove oil pumpb. remove oil pan plate
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Turn the crankshaft until two pistons are at the bottom center. Remove connecting rod caps (1) from the two connecting rods. Remove the lower half of the rod bearing from the rod bearing cap.
The connecting rod bolts are loose on the connecting rods and can fall out when the nuts are removed.
2. Push the connecting rods away from the crankshaft. Remove the upper half of the rod bearing from the connecting rod. Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.3. Install the upper half of the rod bearing in the connecting rod.4. Install the lower half of the rod bearing in the connecting rod cap. Be sure the tabs in the back of the connecting rod bearings are in the tab grooves of the connecting rod and cap. 5. Use Plastigage (A) to check the connecting rod bearing clearance.6. Put Plastigage (A) on the connecting rod bearing.7. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts.
When connecting rod caps are installed, make sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
Do not turn the crankshaft when Plastigage (A) is in position.
Do not use an impact wrench to tighten the nuts the additional 90°.
8. Install connecting rod cap (1). Install the nuts. Tighten the nuts to a torque of 40 4 N m (30 3 lb ft) Put a mark on each nut and the end of each bolt. Tighten the nuts 90° more. Remove the connecting rod caps. Remove Plastigage (A) and measure the width of the Plastigage. The connecting rod clearance must be 0.076 to 0.168 mm (.0030 to .0066 in) for new bearings. The maximum clearance with used bearings is 0.25 mm (.010 in).9. Install the connecting rod caps and tighten the nuts as in Step 8.10. Do Steps 1 through 9 for the remainder of the connecting rod bearings.End By:a. install oil pan plateb. install oil pump
Perform Scheduled Oil Sampling on oil wetted compartments after performing service work to check for contaminants left in the system following repair. Contaminants put into the system may cause rapid wear and shortened component life.

Have questions with 19000-04402?





Group cross 19000-04402

Back to top