Information pump assy, injecti
Rating:
Components :
| 001. | PUMP ASSY, INJECTI | 19000-04132 |
| 002. | BODY ASSY, INJECTI | 09010-03732 |
| 003. | TIMER ASSY, AUTOMA | 09180-00400 |
| 004. | PUMP ASSY, FUEL FE | 09210-01140 |
Scheme ###:
| 000. | [01] | 19000-04132 | PUMP ASSY, INJECTI | ME006045 |
| 003. | [01] | 09010-03732 | BODY ASSY, INJECTI | 31661-00050 |
| 004. | [01] | 09080-05295 | GOVERNOR ASSY, MEC | ME006046 |
| 005. | [01] | 09210-01140 | PUMP ASSY, FUEL FE | ME016021 |
| 007. | [01] | 94913-00190 | KEY, WOODRUFF | ME703361 |
| 008. | [01] | 94901-50500 | WASHER, SPRING | ME008373 |
| 009. | [01] | 09001-20260 | NUT, TIMER ROUND | ME703450 |
| 010. | [01] | 09001-80190 | COVER, CONTROL RAC | ME022416 |
| 013. | [01] | 90200-06511 | WASHER, PLATE | ME703364 |
| 014. | [06] | 94904-70620 | BOLT, W/WASHER | ME703359 |
| 016. | [01] | 09180-00400 | TIMER ASSY, AUTOMA | ME006022 |
Include in #3:
19000-04132
as PUMP ASSY, INJECTI
Cross reference number
| Part num | Firm num | Firm | Name |
| 19000-04132 | ME006045 | PUMP ASSY, INJECTI |
Information:
Remove Valve Lifters & Push Rods
Start By:a. remove valve cover 1. Remove the cover from the flywheel housing and install Tool (A). Turn the crankshaft with Tool (A) until there is no pressure on rocker arm (2).2. Use Tool (B) as shown to move the rocker arm away from push rod (1). Remove push rod (1). 3. Install Tool (C) on the valve lifter. Remove valve lifter (3) from the block. 4. Remove spring guide (4) from the valve lifter.5. Do Steps 1 through 4 again for the other valve lifters and push rods if necessary.Install Valve Lifters & Push Rods
Any time the valve lifter is removed from the machine, a new spring guide must be installed on the valve lifter.1. Install spring guide (1) on valve lifter (2). 2. Put the valve lifter in position on Tool (A) as shown. Make sure spring guide (1) is in position in the groove (slot) in the valve lifter as shown. 3. Use a soft hammer to install Tool (B) over spring guide (1). Make sure the groove in Tool (B) is in alignment with spring guide (1). 4. Put clean engine oil on valve lifter (2). Use Tool (B) to install the valve lifter in the engine block. Make sure the end of the spring guide is in alignment with the small hole in the block.5. When the valve lifter is in position in the block, use Tool (C) to push the valve lifter off of Tool (C). 6. Use Tool (E) to turn the crankshaft to make sure there is not pressure on the push rods and rocker arms.7. Put push rod (3) in position in the block. Use Tool (D) to move rocker arm (4) away from the push rod far enough to put push rod (3) in position under the rocker arm.End By:a. install valve cover
Start By:a. remove valve cover 1. Remove the cover from the flywheel housing and install Tool (A). Turn the crankshaft with Tool (A) until there is no pressure on rocker arm (2).2. Use Tool (B) as shown to move the rocker arm away from push rod (1). Remove push rod (1). 3. Install Tool (C) on the valve lifter. Remove valve lifter (3) from the block. 4. Remove spring guide (4) from the valve lifter.5. Do Steps 1 through 4 again for the other valve lifters and push rods if necessary.Install Valve Lifters & Push Rods
Any time the valve lifter is removed from the machine, a new spring guide must be installed on the valve lifter.1. Install spring guide (1) on valve lifter (2). 2. Put the valve lifter in position on Tool (A) as shown. Make sure spring guide (1) is in position in the groove (slot) in the valve lifter as shown. 3. Use a soft hammer to install Tool (B) over spring guide (1). Make sure the groove in Tool (B) is in alignment with spring guide (1). 4. Put clean engine oil on valve lifter (2). Use Tool (B) to install the valve lifter in the engine block. Make sure the end of the spring guide is in alignment with the small hole in the block.5. When the valve lifter is in position in the block, use Tool (C) to push the valve lifter off of Tool (C). 6. Use Tool (E) to turn the crankshaft to make sure there is not pressure on the push rods and rocker arms.7. Put push rod (3) in position in the block. Use Tool (D) to move rocker arm (4) away from the push rod far enough to put push rod (3) in position under the rocker arm.End By:a. install valve cover