19000-03832 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

19000-03832 PUMP ASSY, INJECTI
Rating:
48
Buy PUMP ASSY, INJECTI 19000-03832 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 19000-03832
002. BODY ASSY, INJECTI 09010-03922
003. COVER, BEARING 09020-10410
004. GOVERNOR ASSY, MEC 09080-05502
005. TIMER ASSY, AUTOMA 09180-01210
006. PUMP ASSY, FUEL FE 09210-00920
007. COUPLING ASSY 09250-00270

Scheme ###:

000. [01] 19000-03832 PUMP ASSY, INJECTI 22010-2331
004. [01] 09031-00130 VALVE ASSY, OVERFL 22107-1090A
005. [02] 94901-02480 WASHER 22847-1940A
006. [01] 09001-80290 COVER, CONTROL RAC 22114-1020A
007. [06] 94904-71150 BOLT, W/WASHER 6 306 1001 00
008. [01] 09010-03922 BODY ASSY, INJECTI 22110-1590A
009. [01] 09210-00920 PUMP ASSY, FUEL FE 22570-1250A
010. [01] 09080-05502 GOVERNOR ASSY, MEC 22310-1490
011. [01] 94904-73910 BOLT, W/WASHER 22815-2820A
012. [01] 94913-00210 KEY, WOODRUFF 22895-1010A
013. [01] 09250-00270 COUPLING ASSY 22610-1080A
014. [01] 09001-20180 NUT, TIMER ROUND 22511-1070A
015. [01] 09180-01210 TIMER ASSY, AUTOMA 22510-1190A
016. [01] 94901-50590 WASHER, SPRING 22877-1620A

Include in #3:

19000-03832 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
19000-03832  22010-2331  PUMP ASSY, INJECTI




Information:

Start By:a. remove crankshaft vibration damper and pulley
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
When replacement of the front seal is made, a replacement of the wear sleeve must also be made.
1. Remove the two bolts, washers, clamp (1), retainer (2) and the O-ring seal.2. Use tool (A) and a press to remove seal (3).3. Install the O-ring seal, retainer (2) and the two bolts, washers, and clamp (1). 4. Install tool (C) in the bore of retainer (2) as shown.5. Install tool (B) between tool (C) and the wear sleeve. Turn tool (B) with a wrench until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this in two or more places until the wear sleeve is loose.6. Remove tool (C) and the wear sleeve by hand.Install Crankshaft Front Seal And Wear Sleeve
1. Install crankshaft front seal (1) and wear sleeve (2) with tool (A) as follows:a. Put clean engine oil on the seal lip of seal (1) and on the outside diameter of wear sleeve (2). Install seal (1) on wear sleeve (2) as shown.b. Use 6V1541 Quick Cure Primer to clean the outside diameter of crankshaft (3) and the inside diameter of wear sleeve (2).c. Put 9S3265 Retaining Compound on the outside diameter of crankshaft (3) and the inside diameter of wear sleeve (2). Make sure the lip of the seal is toward the engine and the outside diameter bevel of the wear sleeve is toward the outside of the engine.d. Put wear sleeve (2) with seal (1) on the front of the crankshaft as shown in illustration B20159P1. Install tool (A). Tighten the bolt in tool (A) until the inside surface of the installer in tooling (A) makes contact with the end of the crankshaft.End By:a. install crankshaft vibration damper and pulley
Perform Scheduled Oil Sampling on oil wetted compartments after performing service work to check for contaminants left in the system following repair. Contaminants put into the system may cause rapid wear and shortened component life.

Have questions with 19000-03832?





Group cross 19000-03832

Back to top