19000-01401 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

19000-01401 PUMP ASSY, INJECTI
Rating:
48
Buy PUMP ASSY, INJECTI 19000-01401 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 19000-01401
002. BODY ASSY, INJECTI 09010-02671
003. GOVERNOR ASSY, MEC 09080-04882
004. TIMER ASSY, AUTOMA 09180-00400
005. PUMP ASSY, FUEL FE 09210-01030

Scheme ###:

000. [01] 19000-01401 PUMP ASSY, INJECTI 31661-82080
003. [01] 09010-02671 BODY ASSY, INJECTI ME703961
004. [01] 09080-04882 GOVERNOR ASSY, MEC
005. [01] 09210-01030 PUMP ASSY, FUEL FE 31661-83070
007. [01] 94913-00190 KEY, WOODRUFF ME703361
008. [01] 94901-50500 WASHER, SPRING ME008373
009. [01] 09001-20260 NUT, TIMER ROUND ME703450
010. [01] 09001-80190 COVER, CONTROL RAC ME022416
013. [01] 90200-06511 WASHER, PLATE ME703364
014. [06] 94904-70620 BOLT, W/WASHER ME703359
016. [01] 09180-00400 TIMER ASSY, AUTOMA ME006022

Include in #3:

19000-01401 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
19000-01401  31661-8208  PUMP ASSY, INJECTI




Information:

Remove & Install Crankshaft Main Bearings
Start By:a. remove oil pumpb. remove oil pan plate 1. Remove No. 1, 3, 5 and 7 main bearing caps (1). Remove the lower halves of the main bearings from the main bearing caps.
If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area in the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
2. Install Tool (A) in the hole in the crankshaft journal, and turn the crankshaft to remove the upper halves of main bearings (2).3. Remove crankshaft thrust bearings (3) from the rear main bearing. Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly.
Make sure the upper and lower halves of the main bearings are installed so the bearing tabs fit into the notch in the cylinder block and the main bearing caps.
4. Use Tool (A), and install new upper halves of main bearings (2) in the cylinder block. Install new lower halves of main bearings (2) in main bearing caps (1).
When the bearing clearance is checked and the engine is in an upright position (vertical position with cylinder head on top), the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances.
For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531.5. Check the main bearing clearance with Plastigage (B) as follows:a. Put a piece of Plastigage (B) on the crankshaft journals as shown.
Make sure the part number on the main bearing cap is toward the front of the engine and the number on the main bearing cap is the same as the number on the cylinder block on the left side of each main bearing cap.
b. Put main bearing caps (1) in position in the engine. Put 2P2506 Thread Lubricant on the bolt threads and the face of the washers. Install the bolts. Tighten the bolts to a torque of 40 4 N m (30 3 lb ft).c. Put a mark on each bolt and main bearing cap; then tighten the bolts 90° more.d. Remove the main bearing caps, and measure the Plastigage to find the bearing clearance. The main bearing clearance for new bearings must be 0.076 to 0.165 mm (.0030 to .0065 in.). Maximum permissible clearance with used bearings is 0.25 mm (.010 in.). 6. Put clean oil on the thrust bearing, and install a new thrust bearing for the rear main bearing. Install the thrust bearing with the identification "BLOCK SIDE" toward the cylinder block and the

Have questions with 19000-01401?





Group cross 19000-01401

Back to top