Information assy nzl
Nozzle:
0935000990
Rating:
KIT List:
| Body assy, injecti | 1904400320 |
| Governor assy, mec | 1908900170 |
| Pump assy, fuel fe | 1922900060 |
Cross reference number
| Part num | Firm num | Firm | Name |
| 19000-00570 | ASSY Nzl | ||
| 01707643 | MITSUI DEUTZ | PUMP ASSY, INJECTI |
Information:
Excavator336F (S/N: TZA1-381; RKB1-1275; RBC1-190; KFT1-298; WTZ1-229)Introduction
On the machines listed above, the Delayed Engine Shutdown (DES) feature delays the engine from shutting off until the Diesel Exhaust Fluid (DEF) injector has cooled. Installing the DEF phase change tank decreases the frequency of the DES feature activating.Safety Section
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Required Parts
Table 1
Required Parts
Item Qty Part Number Part Name
4 6 428-8808 Hose Clamp
5 1 467-9633 Hose
7 1 469-6277 Hose
8 1 424-1209 Tank
9 1 467-9636 Hose
10 1 6V-3250 O-Ring Seal
11 1 7X-1448 Elbow
12 1 454-4235 Plate
13 2 326-4516 Cable Tie
14 1 471-9825 Support As
15 2 8T-4189 Bolt
16 2 8T-4224 Hard Washer Installation Procedure
Illustration 1 g06123834
Remove support (1) from the engine compartment.
Illustration 2 g06123840
Locate insulation (2) on the engine hood.
Illustration 3 g06123843
Raise the insulation approximately 30 mm (1.2 inch) to avoid interference with the new tank.
Illustration 4 g06123848
Loosen the worm-drive clamps and remove two hoses (3) from the DEF system. Save the cushion clamps and hardware for reuse.
Illustration 5 g06123850
(4) 428-8808 Hose Clamp
(5) 467-9633 Hose
(6) Cushion clamp (reuse)
Install hose (5) and two clamps (4). Slowly tighten the clamps to 6.6 0.2 N m (58 1.8 lb in). Install cushion clamp (6) (previously removed) onto the hose.
Illustration 6 g06123852
(4) 428-8808 Hose Clamp
(6) Cushion clamp (reuse)
(7) 469-6277 Hose
(8) 424-1209 Tank
Connect one end of hose (7) to the tube on the engine using clamp (4). Slowly tighte
On the machines listed above, the Delayed Engine Shutdown (DES) feature delays the engine from shutting off until the Diesel Exhaust Fluid (DEF) injector has cooled. Installing the DEF phase change tank decreases the frequency of the DES feature activating.Safety Section
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Required Parts
Table 1
Required Parts
Item Qty Part Number Part Name
4 6 428-8808 Hose Clamp
5 1 467-9633 Hose
7 1 469-6277 Hose
8 1 424-1209 Tank
9 1 467-9636 Hose
10 1 6V-3250 O-Ring Seal
11 1 7X-1448 Elbow
12 1 454-4235 Plate
13 2 326-4516 Cable Tie
14 1 471-9825 Support As
15 2 8T-4189 Bolt
16 2 8T-4224 Hard Washer Installation Procedure
Illustration 1 g06123834
Remove support (1) from the engine compartment.
Illustration 2 g06123840
Locate insulation (2) on the engine hood.
Illustration 3 g06123843
Raise the insulation approximately 30 mm (1.2 inch) to avoid interference with the new tank.
Illustration 4 g06123848
Loosen the worm-drive clamps and remove two hoses (3) from the DEF system. Save the cushion clamps and hardware for reuse.
Illustration 5 g06123850
(4) 428-8808 Hose Clamp
(5) 467-9633 Hose
(6) Cushion clamp (reuse)
Install hose (5) and two clamps (4). Slowly tighten the clamps to 6.6 0.2 N m (58 1.8 lb in). Install cushion clamp (6) (previously removed) onto the hose.
Illustration 6 g06123852
(4) 428-8808 Hose Clamp
(6) Cushion clamp (reuse)
(7) 469-6277 Hose
(8) 424-1209 Tank
Connect one end of hose (7) to the tube on the engine using clamp (4). Slowly tighte