Fuel injectors
  1. Home
  2. denso
  3. #09649-00271

09649-00271 COMPENSATOR SUB-AS Denso Cross


 

Information compensator sub-as

09649-00271 COMPENSATOR SUB-AS
Rating:
12
Buy COMPENSATOR SUB-AS 09649-00271 genuine, new aftermarket engine parts with delivery

Scheme ###:

COMPENSATOR SUB-AS
000. [01] 09649-00271 COMPENSATOR SUB-AS
001. [01] 09644-00363 COVER SUB-ASSY, GO
002. [01] 09644-00800 COVER SUB-ASSY, GO
003. [01] 09621-60030 STOPPER, TIMER SLI ME736268
004. [01] 09646-50250 R0D, PUSH
005. [01] 09611-80160 BUSHING, GUIDE ME736270
006. [01] 19263-10010 DIAPHRAGM ME736271
007. [01] 09624-60020 SHEET, PLUNGER SPR ME736272
008. [01] 09611-80190 BUSHING, GUIDE ME736273
009. [01] 94905-04070 NUT, HEXAGON ME736274
010. [01] 09621-10070 CLIP, TIMER ME736275
011. [01] 09645-50090 PIN, LEVER CONECTI ME736276
012. [01] 09611-80020 BUSHING, GUIDE ME736277
013. [01] 09625-40020 NUT, GOVERNOR SHAF ME736278
014. [01] 94901-81680 WASHER, COPPER PLA ME736279
015. [01] 09604-90051 O-RING
016. [01] 09627-20040 PIN, LEVER SUPPORT ME736281
017. [01] 09629-50080 LEVER SUB-ASSY, CO ME736482
018. [02] 09024-80010 WASHER, DRAIN SCRE ME702175
019. [02] 91518-06121 BOLT, W/WASHER ME703399
019. [02] 91518-06141 BOLT, W/WASHER ME736842
019. [04] 91518-06141 BOLT, W/WASHER ME736842
020. [02] 09626-90032 BOLT, GOVERNOR LIN ME736284
021. [01] 09604-90180 O-RING ME736285
022. [01] 94905-04100 NUT, HEXAGON ME736286
023. [01] 90200-08211 WASHER, PLATE ME736287
024. [01] 90176-06361 NUT, HEXAGON ME736288
025. [01] 09602-00080 SCREW SUB-ASSY, OV
025. [01] 09602-00110 SCREW SUB-ASSY, OV
026. [01] 09024-10010 WASHER, AIR BLEEDE ME702102
027. [01] 09031-70130 PLUG, SCREW ME703104
028. [01] 09649-20070 SPRING, BOOST COMP
029. [1C] 09649-30120 SHIM, BOOST COMPEN ME736300
029. [1C] 09649-30110 SHIM, BOOST COMPEN ME736299
029. [1C] 09649-30100 SHIM, BOOST COMPEN ME736298
029. [1C] 09649-30090 SHIM, BOOST COMPEN ME736297
029. [1C] 09649-30080 SHIM, BOOST COMPEN ME736296
029. [1C] 09649-30070 SHIM, BOOST COMPEN ME736295
029. [1C] 09649-30060 SHIM, BOOST COMPEN ME736294
029. [1C] 09649-30010 SHIM, BOOST COMPEN ME736305
029. [1C] 09649-30020 SHIM, BOOST COMPEN ME736306
029. [1C] 09649-30030 SHIM, BOOST COMPEN ME736307
029. [1C] 09649-30040 SHIM, BOOST COMPEN ME736292
029. [1C] 09649-30050 SHIM, BOOST COMPEN ME736293
030. [01] 19263-30010 WASHER, THRUST ME736308
031. [02] 90260-00601 WASHER, WAVE MM501078
032. [02] 94904-06511 BOLT, HEXAGON
033. [01] 94901-17700 WASHER, STEEL PLAT ME728835

Include in #3:

09600-02920 as COMPENSATOR SUB-AS
09649-00271

Cross reference number



Part num Firm num Firm Name
09649-00271    COMPENSATOR SUB-AS




Information:

Camshaft
When reconditioning an engine, check the diameter of the camshaft bearing journals and the camshaft lobe height.Camshaft bearing journals have a diameter of 2.5000 .0005 in. (63.500 0.013 mm) and the minimum diameter worn is 2.4970 in. (63.424 mm).To find lobe lift (A) of camshaft, use the following procedure:1. Measure lobe height (B) of one exhaust and one intake lobe.2. Measure base circle (C) of one exhaust and one intake lobe.3. Subtract base circle (C) dimension (STEP 2) from lobe height (B) dimension (STEP 1). The difference is actual lobe lift (A).4. The specified (new) lobe lift (A) is: (a) Exhaust lobe ... .3071 in.(7.800 mm)(b) Intake lobe ... .3077 in.(7.816 mm)5. The maximum permissible difference between actual lobe lift (STEP 3) and specified lobe lift (STEP 4) is .025 in. (0.64 mm).
CAMSHAFT LOBE
A. Lobe lift. B. Lobe height. C. Base circle.With camshaft installed in the cylinder block, check end play. End play with new components should be .007 .003 in. (0.18 0.08 mm). The maximum permissible end play is .020 in. (0.51 mm).Camshaft Followers
Use an 8S2293 Magnet to remove the cam followers.
REMOVING CAM FOLLOWERSCam followers establish a wear pattern with the camshaft lobes. Identify and reinstall the followers removed. Dishing or circular wear pattern is allowed on the cam follower face, providing the wear face keeps a polished appearance. Replace the follower if the wear face is rough or shows signs of scuffing. A new follower can be used with an old camshaft, providing the lobe is in good condition. Put engine oil on the cam followers and the camshaft lobes before installing the cam followers. Use new cam followers with a new camshaft.Camshaft Gears
1. Remove screw (1) and washer (2) from end of camshaft.
REMOVING TIMING ADVANCE RETAINING SCREW
1. Screw. 2. Washer.2. Remove timing advance unit from the camshaft.3. Install puller (A), with spacer (C) over the shaft in the camshaft spacer (B) on spacer (C) as shown and remove the gear from the camshaft.
REMOVING GEAR (Typical Example)
A. 1P2321 Puller. B. 8S5579 Spacer. C. 9S9155 Spacer.To install the gear use the following procedure:1. Heat the gear to a temperature of approximately 400°F (204°C) before installing on the camshaft.
Do not heat the gear with a torch. Do not heat the gear to a temperature of more than 600°F (315°C). Heating the gear with a torch or to a temperature of more than 600°F (315°C) may cause the two drive dowels for the automatic timing advance to loosen and come out of the gear.
2. Align slot in gear hub with the pin in the camshaft. Install the gear on the camshaft with timing mark on gear aligned with timing mark on crankshaft gear. Be sure the gear is completly seated against the shoulder of the camshaft.
Do not drive the gear on the camshaft.
3. Align holes in weights with dowels in gear and install the automatic timing advance.4. Align pin (3) in washer with hole (4) in camshaft and install washer (2).5. Install screw (1) and

Have questions with 09649-00271?





19260-01860 COMPENSATOR SUB-AS 19260-01850 19260-01840 19260-01830 19260-01820
09649-00011 COMPENSATOR SUB-AS 09649-00191 09649-00221 09649-00241 09649-00280

Group cross 09649-00271

Back to top