Fuel injectors
  1. Home
  2. denso
  3. #09649-00221

09649-00221 COMPENSATOR SUB-AS Denso Cross


 

Information compensator sub-as

09649-00221 COMPENSATOR SUB-AS
Rating:
36
Buy COMPENSATOR SUB-AS 09649-00221 genuine, new aftermarket engine parts with delivery

Scheme ###:

COMPENSATOR SUB-AS
000. [01] 09649-00221 COMPENSATOR SUB-AS
000. [01] 09649-00221 COMPENSATOR SUB-AS
001. [01] 09644-00351 COVER SUB-ASSY, GO 22703-87704-000
001. [01] 09644-00351 COVER SUB-ASSY, GO
002. [01] 09644-00320 COVER SUB-ASSY, GO 22703-64520-000
002. [01] 09644-00320 COVER SUB-ASSY, GO 22703-64520
003. [01] 09621-60030 STOPPER, TIMER SLI 22419-87701-000
003. [01] 09621-60030 STOPPER, TIMER SLI 22658-64518
004. [01] 09646-50391 R0D, PUSH 22321-64850-000
004. [01] 09646-50391 R0D, PUSH 22321-64850
005. [01] 09611-80160 BUSHING, GUIDE 22348-87702-000
005. [01] 09611-80160 BUSHING, GUIDE 22348-64360
006. [01] 19263-10010 DIAPHRAGM 22303-87701-000
006. [01] 19263-10010 DIAPHRAGM 22542-54260
007. [01] 09624-60020 SHEET, PLUNGER SPR 22143-54260
007. [01] 09624-60020 SHEET, PLUNGER SPR 22143-87702-000
008. [01] 09611-80190 BUSHING, GUIDE 22348-87701-000
008. [01] 09611-80190 BUSHING, GUIDE 22348-54490
009. [01] 94905-04070 NUT, HEXAGON 90099-05156
009. [01] 94905-04070 NUT, HEXAGON 22493-87702-000
010. [01] 09621-10070 CLIP, TIMER 22656-54490
010. [01] 09621-10070 CLIP, TIMER 22293-87701-000
011. [01] 09645-50090 PIN, LEVER CONECTI 22338-87701-000
011. [01] 09645-50090 PIN, LEVER CONECTI 22338-54120
012. [01] 09611-80020 BUSHING, GUIDE 22348-54121
012. [01] 09611-80020 BUSHING, GUIDE 22348-87703-000
013. [01] 09625-40021 NUT, GOVERNOR SHAF 22722-87702-000
013. [01] 09625-40021 NUT, GOVERNOR SHAF 22722-54120
014. [01] 94901-81680 WASHER, COPPER PLA 90099-01473
014. [01] 94901-81680 WASHER, COPPER PLA 22119-87702-000
015. [01] 09604-90230 O-RING 22193-55031
015. [01] 09604-90230 O-RING 22193-55031-000
016. [01] 09627-20040 PIN, LEVER SUPPORT 22526-87701-000
016. [01] 09627-20040 PIN, LEVER SUPPORT 22526-54120
017. [01] 09629-50070 LEVER SUB-ASSY, CO 22308-87702-000
017. [01] 09629-50070 LEVER SUB-ASSY, CO 22308-54120
017. [01] 09629-50670 LEVER SUB-ASSY, CO
017. [01] 09629-50670 LEVER SUB-ASSY, CO
018. [02] 09024-80010 WASHER, DRAIN SCRE 22378-76010
018. [02] 09642-60110 GASKET, DELIVERY V 22149-6D450-000
018. [02] 09024-80010 WASHER, DRAIN SCRE 22378-87701-000
018. [02] 09642-60110 GASKET, DELIVERY V 22149-6D450
019. [04] 09644-90130 BOLT, SOCKET 22395-54263
019. [04] 09644-90130 BOLT, SOCKET 22395-54263-000
020. [02] 09626-90032 BOLT, GOVERNOR LIN 22739-54120
020. [02] 09626-90032 BOLT, GOVERNOR LIN 22739-87703-000
021. [01] 09604-90180 O-RING 22193-54561
021. [01] 09604-90180 O-RING 22292-87703-000
022. [01] 94905-05430 NUT, HEXAGON 90099-05252
022. [01] 94905-04100 NUT, HEXAGON 90099-05181
022. [01] 94905-05430 NUT, HEXAGON 90092-05252-000
022. [01] 94905-04100 NUT, HEXAGON 22493-87703-000
023. [01] 90200-08211 WASHER, PLATE 90093-00802
023. [01] 90200-08211 WASHER, PLATE 22113-87701-000
024. [01] 90176-06361 NUT, HEXAGON 90092-20608
024. [01] 90176-06361 NUT, HEXAGON 22135-87701-000
025. [01] 09602-00110 SCREW SUB-ASSY, OV 22160-87702-000
025. [01] 09602-00110 SCREW SUB-ASSY, OV 22160-54262
026. [01] 09642-60120 GASKET, DELIVERY V 22149-54800-000
026. [01] 09024-10010 WASHER, AIR BLEEDE 22119-77020-000
026. [01] 09642-60120 GASKET, DELIVERY V 22149-54800
026. [01] 09024-10010 WASHER, AIR BLEEDE 22119-77020
027. [01] 09031-70130 PLUG, SCREW 22129-54120-000
027. [01] 09031-70130 PLUG, SCREW 22129-54120
028. [1C] 09649-20150 SPRING, BOOST COMP 22546-54490
028. [1C] 09649-20170 SPRING, BOOST COMP 22546-54492-000
028. [1C] 09649-20170 SPRING, BOOST COMP 22546-54492
028. [1C] 09649-20160 SPRING, BOOST COMP 22546-54491-000
028. [1C] 09649-20150 SPRING, BOOST COMP 22546-54490-000
028. [1C] 09649-20160 SPRING, BOOST COMP 22546-54491
030. [01] 19263-30010 WASHER, THRUST 22332-87701-000
030. [01] 19263-30010 WASHER, THRUST 22549-17140

Include in #3:

09649-00221 as COMPENSATOR SUB-AS
09649-00221

Cross reference number



Part num Firm num Firm Name
09649-00221    COMPENSATOR SUB-AS




Information:

Introduction
Do not perform any procedure in this Special Instruction until you read this information and you understand this information. This Special Instruction is intended for the installation of the 257-4183 Injector Wiring Harness Kit . The 257-4183 Injector Wiring Harness Kit can be used to repair fuel injector connectors.
Table 1
Required Tools    
Tool     Part Number     Part Name     Qty    
A     9S-9150     Terminal Crimp Tool As     1    
B     9U-6070     Heat Gun Gp     1    Removal of a Faulty Connector from the Wire Harness
The following steps can be used in order to remove a faulty connector for an injector on the wire harness that is located under the valve mechanism cover.
Identify the connector that needs to be replaced. Wiring for the injector solenoid is not sensitive to polarity.
Illustration 1 g01111254
Connector that is cut from the wire harness
Cut wire (1) at a distance of 70 mm (2.8 inch) from the rear surface of the connector.
Cut wire (2) at a distance of 65 mm (2.6 inch) from the rear surface of the connector.
Illustration 2 g01111314
(3) Wire from the harness for side (B) on the connector (4) Wire from the harness for side (A) on the connectorNote: The wires on the old connector are cut to length so that the wires on the wire harness will match up to the new connector. Cutting the wires to the proper length will aid in matching the harness wires to the wires on the new connector.
Discard the old connector.Installation of a New Connector
The following steps can be used in order to install a new connector for an injector on the wire harness that is located under the valve mechanism cover.
Use Tool (A) in order to remove 5 mm (0.2 inch) of the plastic from wires (3) and (4) .
Illustration 3 g01111333
Connecting the connector to the wire harness (A) Side (A) of the new connector (B) Side (B) of the new connector (3) Wire from the harness for side (B) on the new connector (4) Wire from the harness for side (A) on the new connector (5) Heat shrink tubes (6) Butt splice on the wire that is on side (A) of the new connector (7) Butt splice on the wire that is on side (B) of the new connector
Use heat shrink tubes (5) from the 257-4183 Injector Wiring Harness Kit . Slide the heat shrink tubes toward the connector in order to expose the butt splices.
Insert wire (4) into butt splice (6) .
Insert wire (3) into butt splice (7) .

Have questions with 09649-00221?





19260-01860 COMPENSATOR SUB-AS 19260-01850 19260-01840 19260-01830 19260-01820
09649-00241 COMPENSATOR SUB-AS 09649-00331 09649-00361 09649-00461 09649-00720

Group cross 09649-00221

Back to top