Information governor assy, tor
Rating:
Scheme ###:
| 000. | [01] | 09627-01060 | GOVERNOR ASSY, TOR | 22350-87602-000 |
| 001. | [01] | 09627-10071 | LEVER, GUIDE | |
| 002. | [01] | 09628-50280 | LEVER SUB-ASSY, TE | |
| 003. | [01] | 09627-50140 | LEVER SUB-ASSY, SU | |
| 004. | [01] | 09627-20020 | PIN, LEVER SUPPORT | |
| 005. | [01] | 09627-30020 | WASHER, GOVERNOR T | |
| 006. | [2C] | 09627-30110 | WASHER, GOVERNOR T | |
| 006. | [2C] | 09627-30180 | WASHER, GOVERNOR T | |
| 007. | [01] | 09627-30030 | WASHER, GOVERNOR T | |
| 008. | [1C] | 09628-80260 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80250 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80240 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80230 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80220 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80200 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80180 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80170 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80160 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80090 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80050 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80040 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80030 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80020 | SPRING, DAMPER | |
| 008. | [1C] | 09628-80270 | SPRING, DAMPER |
Include in #3:
Cross reference number
| Part num | Firm num | Firm | Name |
| 09627-01060 | 22350-8760 | GOVERNOR ASSY, TOR | |
| 22350-87602-000 | DAIHATSU | GOVERNOR ASSY, TOR | |
| 22350-5B880 | TOYOTA | GOVERNOR ASSY, TOR |
Information:
(8) Bore in bearing for balancer shaft (installed) ... 53.050 0.061 mm (2.0886 .0024 in) Bore in block for bearings ... 57.851 .025 mm (2.2776 .0010 in)Depth to install bearings at both ends of block ... 0.8 0.5 mm (.03 .02 in)(9) Depth from front face of block to install center bearings ... 290.6 0.5 mm (11.44 .02 in)
There are holes in the bores for the main bearings, between the cylinders for piston cooler orifices. These holes must have either orifices (11) or plugs (10) installed.
(10) Plug.(11) Piston cooling orifice. (12) Distance two dowels extend from the surface of the cylinder block ... 19.8 0.5 mm (.78 .02 in)(13) Distance hollow dowel extends from the surface of the cylinder block ... 16.0 0.5 mm (.63 .02 in)(14) Depth to install two dowels below the surface of the cylinder block ... 1.0 0.5 mm (.04 .02 in)(15) Distance dowel extends from the front face of the cylinder block ... 15.7 0.5 mm (.62 .02 in)(16) Distance two dowels extend from the rear face of the cylinder block ... 12.7 0.5 mm (.50 .02 in)(17) Distance dowel extends from the front face of the cylinder block ... 22.4 0.5 mm (.88 .02 in)
There are holes in the bores for the main bearings, between the cylinders for piston cooler orifices. These holes must have either orifices (11) or plugs (10) installed.
(10) Plug.(11) Piston cooling orifice. (12) Distance two dowels extend from the surface of the cylinder block ... 19.8 0.5 mm (.78 .02 in)(13) Distance hollow dowel extends from the surface of the cylinder block ... 16.0 0.5 mm (.63 .02 in)(14) Depth to install two dowels below the surface of the cylinder block ... 1.0 0.5 mm (.04 .02 in)(15) Distance dowel extends from the front face of the cylinder block ... 15.7 0.5 mm (.62 .02 in)(16) Distance two dowels extend from the rear face of the cylinder block ... 12.7 0.5 mm (.50 .02 in)(17) Distance dowel extends from the front face of the cylinder block ... 22.4 0.5 mm (.88 .02 in)