09618-00280 RING SUB-ASSY, ROL Denso Cross


 

Information ring sub-assy, rol

RING SUB-ASSY, ROL AA
  • IN THE ROLLER PIN KIT,NO.2,3,4,5 EACH INCLUDE 4 PIECES.
09618-00280 RING SUB-ASSY, ROL
Rating:
34
Buy RING SUB-ASSY, ROL 09618-00280 genuine, new aftermarket engine parts with delivery

Scheme ###:

000. [01] 09618-00280 RING SUB-ASSY, ROL
000. [01] 09618-00280 RING SUB-ASSY, ROL 22108-17840
001. [01] 09618-10280 RING, ROLLER
001. [01] 09618-10280 RING, ROLLER
002. [04] 09618-40020 PIN, ROLLER
002. [04] 09618-40020 PIN, ROLLER
003. [04] 09618-50020 BUSH, ROLLER
003. [04] 09618-50020 BUSH, ROLLER
004. [04] 09618-70050 ROLLER
004. [04] 09618-70030 ROLLER
004. [04] 09618-70050 ROLLER
004. [04] 09618-70030 ROLLER
005. [04] 09618-90020 PLATE, ROLLER
005. [04] 09618-90020 PLATE, ROLLER
020. [01] 09601-00930 OVER-HAUL KIT, DIS
020. [01] 09601-00930 OVER-HAUL KIT, DIS

Cross reference number



Part num Firm num Firm Name
09618-00280  22108-1784  RING SUB-ASSY, ROL
22108-17840    TOYOTA RING SUB-ASSY, ROL




Information:

Start By:a. remove fuel injection linesb. remove fuel filter and basec. remove fuel transfer pump The following illustrations are of a 3304 Engine. 1. Disconnect the governor control linkage from the governor.2. On 3304 Engines only: remove oil supply line (1), oil drain line (2) and heat shield (3). Remove the O-ring seal from oil drain line (2) if it is damaged. Remove the gaskets and screen from the top of the turbocharger.3. Disconnect fuel drain lines (4) and (5) from the fuel injection pump housing and governor. 4. Remove the nuts, washers and cover from the timing gear housing. Remove studs (6) if they are damaged or loose.5. Loosen bolt (7) enough to leave a gap of 3.18 mm (.125 in) between washer (8) and the fuel pump drive gear.6. Install Tool (A) as shown. Tighten the stud to pull the fuel pump drive gear loose from the taper on the fuel injection pump camshaft.7. Remove Tool (A), bolt (7) and washer (8) from the engine. 8. Fasten a nylon strap and hoist to the fuel injection pump housing and governor. The 3304 fuel injection pump housing and governor weighs 24 kg (53 lb). The 3306 fuel injection pump housing and governor weighs 29 kg (64 lb).9. Remove bolt (9), bolt (10), three nuts (11) and the fuel injection pump housing and governor. Remove the two O-ring seals from the bottom and the two O-ring seals from the front of the fuel injection pump housing and governor.Install Fuel Injection Pump Housing & Governor
The following illustrations are of a 3304 Engine. 1. Put clean engine oil on the O-ring seals. Install O-ring seals (1) in the bottom and O-ring seals (2) in the front of the fuel injection pump housing and governor. 2. Make sure O-ring seals (1) and (2) stay in position in the fuel injection pump housing and governor. Fasten a hoist to the fuel injection pump housing and governor, and put it in position on the engine. Install the two bolts at location (5) and the three nuts on studs (3) to hold the fuel injection pump housing and governor in position.3. Remove the bolts that hold cover (4) in position. Remove cover (4) and the gasket. 4. Put Tool (A) in position as shown. Install the bolt that holds the fuel pump drive gear to the fuel injection pump camshaft without the washer. This will allow the camshaft in the fuel system to be turned.5. Put pressure on the end of Tool (A) and turn the camshaft slowly until the Tool drops into the groove (slot) in the camshaft. Leave Tool (A) in position in the groove (slot). Remove the bolt from the end of the camshaft. 6. Install washer (6) with the large diameter toward the front of the engine. Install bolt (7) and tighten it to a torque of 6.8 N m (60 lb in).7. Install Tool (B) as shown in the flywheel housing. Make sure bolt (7) does not loosen as

Have questions with 09618-00280?





Group cross 09618-00280

Back to top