Fuel injectors
  1. Home
  2. denso
  3. #09601-00830

09601-00830 OVER-HAUL KIT, DIS Denso Cross


 

Information over-haul kit, dis

09601-00830 OVER-HAUL KIT, DIS
Rating:
26
Buy OVER-HAUL KIT, DIS 09601-00830 genuine, new aftermarket engine parts with delivery

Components :

001. OVER-HAUL KIT, DIS 09601-00830

Scheme ###:

OVER-HAUL KIT, DIS
000. [01] 09601-00830 OVER-HAUL KIT, DIS
002-002. [01] 09653-00071 FILTER, SUB-ASSY 8-97141571-0
003-001. [01] 02947-50080 O-RING
017. [04] 09642-60140 GASKET, DELIVERY V
029. [01] 09604-90330 O-RING
037. [01] 09646-80310 CAP RUBBER 8-97238597-0
038. [02] 09604-90540 O-RING
042. [01] 09604-90510 O-RING 8-97209532-0
049. [01] 94914-02980 O-RING 8-97141158-0
050. [01] 09604-90220 O-RING
052. [01] 09653-50020 GASKET, SPILL VALV
054. [05] 09024-10010 WASHER, AIR BLEEDE 8-97141182-0
055. [01] 09604-90320 O-RING
058. [01] 09644-60100 GASKET, GOVERNOR C 8-97141201-0
062-001. [01] 09604-90180 O-RING 8-97141212-0
062-002. [01] 09604-90500 O-RING 8-97209534-0
067. [04] 09001-40012 CAP, VALVE HOLDER
070. [02] 09646-80060 CAP RUBBER
071-001. [01] 09604-90530 O-RING
071-002. [01] 09604-90520 O-RING
075. [01] 09653-00111 FILTER, SUB-ASSY
076. [01] 09604-90460 O-RING
080. [01] 09604-90420 O-RING 8-97141471-0

Include in #3:

09601-00830 as OVER-HAUL KIT, DIS
09650-05013

Cross reference number



Part num Firm num Firm Name
09601-00830    OVER-HAUL KIT, DIS

Use as kit:

0965005010 0965005010 Pump assy, injecti 0960100830




Information:

1. Disconnect air line (1) at fitting. Remove two bolts (2). Pull up and toward the front of the engine to remove the bolt of the fuel ratio from the groove (slot) in the collar for the governor. Remove fuel ratio control (3). Remove gasket from fuel ratio control.2. Install a new gasket on fuel ratio control. Install fuel ratio control (3). Make sure bolt engages with stop collar in governor control.3. Install two bolts (2). Connect air line (1) at fitting.4. Make sure the fuel ratio control is in correct adjustment. See Systems Operation Testing & Adjusting Manual for this procedure.5. Install a new governor seal.Disassemble Fuel Ratio Control
Start By:a. remove fuel ratio control 1. Remove two bolts (1) and the housing (2). 2. Remove valve assembly (3).3. Remove seal (4) and O-ring seal from valve.4. Remove the retainer (5) and two springs (6). 5. Remove three bolts (9) and cover (10).6. Remove valve (7), diaphragm (8), retainer and spring. 7. Remove pin (12) from valve (7).8. Remove cover (11) from the valve.9. Remove the seal from the cover (11).Assemble Fuel Ratio Control
1. Put clean engine oil on lip of seal. Install the seal (1) in cover (2). Install seal so lip of seal is toward the inside of the cover. 2. Install the valve (3) into cover (2).3. Install the pin that holds cover on valve. 4. Install spring (7) and the retainer (6) in cover (8).5. Install diaphragm (5) on the valve assembly (4) and in the cover. 6. Install cover and three bolts (11) that hold covers together.7. Put clean engine oil on seal and ring seal. Install the seals (10) on valve.8. Install the two springs (13), retainer and valve assembly (12).9. Install housing (9) and two bolts.
Correct adjustment must be made to fuel ratio control before installation. See Systems Operation Testing & Adjusting for this procedure.
End By:a. install fuel ratio control

Have questions with 09601-00830?





19089-01260 OVER-HAUL KIT, GOV 19089-01161 19089-01160 19089-01090 19089-00980
09601-00020 OVER-HAUL KIT, DIS 09601-00030 09601-00110 09601-00140 09601-00520

Group cross 09601-00830

Back to top