Information injector assy
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
0950005982 095000-5982 6X Fuel Injector for Isuzu Series 6HK1 4HK1 Engine
TUWODE Part Number: 950005982 095000-5982 || Item Type: Fuel Injector || Applicable Models: Fit for Isuzu F Series 6HK1 4HK1 Engine || Well-functioning fuel injectors ensure the correct air-fuel ratio, which is essential for minimizing harmful emissions. || Fuel is broken into fine droplets for optimal air mixing and enhanced combustion efficiency.
TUWODE Part Number: 950005982 095000-5982 || Item Type: Fuel Injector || Applicable Models: Fit for Isuzu F Series 6HK1 4HK1 Engine || Well-functioning fuel injectors ensure the correct air-fuel ratio, which is essential for minimizing harmful emissions. || Fuel is broken into fine droplets for optimal air mixing and enhanced combustion efficiency.
BCXFORK Fuel Injector 095000-5982 095000-5980 fits for Isuzu Engine 4HK1 7.8L 6HK1 5.2L
BCXFORK NOTE Before placing an order, please verify that your part number matches the one in the listing. Some Fuel Injectors may look similar. If you're unsure, you can leave us a message and provide a picture of your old fuel injector for verification. || Note: We can provide various engine parts. If you need any additional parts, please leave us a message with the list of items you need. || Manufacturer Warranty 1 Year || Part Number: 095000-5982 095000-5980 || This item fits for Isuzu Engine 4HK1 7.8L 6HK1 5.2L
BCXFORK NOTE Before placing an order, please verify that your part number matches the one in the listing. Some Fuel Injectors may look similar. If you're unsure, you can leave us a message and provide a picture of your old fuel injector for verification. || Note: We can provide various engine parts. If you need any additional parts, please leave us a message with the list of items you need. || Manufacturer Warranty 1 Year || Part Number: 095000-5982 095000-5980 || This item fits for Isuzu Engine 4HK1 7.8L 6HK1 5.2L
$791.79
09 Aug 2024
CN: CAR REFINE
4PCS Fuel Injector Mechanism fits Model 095000-5982 095000-5980 for Isuzu Engine 4HK1 7.8L
Podafu Item Type: Fuel Injector || Part Code: 095000-5982 || Applicable Models: Compatible with Isuzu Engine 4HK1 7.8L || Provides consistent fuel delivery to ensure smooth engine operation. || Extends the engine's peak performance, thereby improving the vehicle's dependability.
Podafu Item Type: Fuel Injector || Part Code: 095000-5982 || Applicable Models: Compatible with Isuzu Engine 4HK1 7.8L || Provides consistent fuel delivery to ensure smooth engine operation. || Extends the engine's peak performance, thereby improving the vehicle's dependability.
You can express buy:
USD 168
10-11-2022
10-11-2022
USD 185
10-11-2022
10-11-2022
USD 168
10-11-2022
10-11-2022
Include in #3:
Cross reference number
| Part num | Firm num | Firm | Name |
| 09500-05982 | 8-97603099 | INJECTOR ASSY |
Information:
Storage Procedure
When a generator is in storage for any length of time, moisture condenses in the windings. Minimize the condensation by use of a dry storage space and space heaters. Refer to step 2 belowIf a brush-type generator (SRCR) is to be in storage for a year or more, lift the brushes off the slip ring to prevent damage to the slip ring by chemical action.After Storage
Test the main stator windings with a megohmmeter in the following situations: 1. Before initial startup of generator set.2. Every 3 months* if generator is operating in a humid environment.3. If generator has not been run under load for 3 months* or more.*This is a guideline only. It may be necessary to megger more frequently if environment is extremely humid, salty or if the last megger test was close to 1 megohm.The megohmmeter test is described in Service Manuals SENR2180 or SENR7968. A reading of 1 meghom or less indicates that the winding has absorbed too much moisture.To Remove Moisture
To remove moisture caused by high humidity, use one of the following methods to make the generator dry:1. Energize space heaters in generator if so equipped.2. Put the generator in an oven at a temperature of not more than 85°C (185°F) for four hours.
If an oven is used for drying, use a forced air type rather than a radiant type. Radiant ovens can cause localized overheating.
3. Space heaters of the same type used in marine applications, can be installed on generators. (See the Parts Book.) These heaters heat the windings to remove moisture and should be connected at all times in high humidity conditions whenever the generator is not running.4. Use a canvas enclosure around the generator and heating lamps to increase the temperature. Make an opening in the top for release of moisture.5. Send a low voltage current through the windings to increase the temperature of the windings. Do not exceed 85°C (185°F).If the megohmmeter test reads under 1 megohm after the drying or if it goes below 1 megohm shortly after drying, contact your Caterpillar dealer. The insulation has deteriorated and should be reconditioned.
When a generator is in storage for any length of time, moisture condenses in the windings. Minimize the condensation by use of a dry storage space and space heaters. Refer to step 2 belowIf a brush-type generator (SRCR) is to be in storage for a year or more, lift the brushes off the slip ring to prevent damage to the slip ring by chemical action.After Storage
Test the main stator windings with a megohmmeter in the following situations: 1. Before initial startup of generator set.2. Every 3 months* if generator is operating in a humid environment.3. If generator has not been run under load for 3 months* or more.*This is a guideline only. It may be necessary to megger more frequently if environment is extremely humid, salty or if the last megger test was close to 1 megohm.The megohmmeter test is described in Service Manuals SENR2180 or SENR7968. A reading of 1 meghom or less indicates that the winding has absorbed too much moisture.To Remove Moisture
To remove moisture caused by high humidity, use one of the following methods to make the generator dry:1. Energize space heaters in generator if so equipped.2. Put the generator in an oven at a temperature of not more than 85°C (185°F) for four hours.
If an oven is used for drying, use a forced air type rather than a radiant type. Radiant ovens can cause localized overheating.
3. Space heaters of the same type used in marine applications, can be installed on generators. (See the Parts Book.) These heaters heat the windings to remove moisture and should be connected at all times in high humidity conditions whenever the generator is not running.4. Use a canvas enclosure around the generator and heating lamps to increase the temperature. Make an opening in the top for release of moisture.5. Send a low voltage current through the windings to increase the temperature of the windings. Do not exceed 85°C (185°F).If the megohmmeter test reads under 1 megohm after the drying or if it goes below 1 megohm shortly after drying, contact your Caterpillar dealer. The insulation has deteriorated and should be reconditioned.