Fuel injectors
  1. Home
  2. denso
  3. #09450-08660

09450-08660 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935003840
09450-08660 PUMP ASSY, INJECTI
Rating:
19
Buy PUMP ASSY, INJECTI 09450-08660 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09450-08660

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09450-08660 PUMP ASSY, INJECTI 30L6504300
001. [01] 09011-03730 HOUSING SUB-ASSY,
002. [03] 09013-00390 HOLDER SUB-ASSY, D 47X0119800
003. [03] 09013-60530 SPRING, DELIVERY V
004. [03] 09013-70130 GASKET, DELIVERY V
005. [03] 09014-02110 VALVE SUB-ASSY, IN
006. [03] 09015-06770 ELEMENT SUB-ASSY, 47X0122800
007. [03] 09016-00140 SLEEVE SUB-ASSY, C
008. [03] 09016-30140 SEAT, SPRING, UPR
009. [03] 09016-40220 SPRING, PUMP PLUNG MM501926
010. [03] 09016-50170 SEAT, SPRING, LWR
011. [03] 09017-00220 TAPPET SUB-ASSY,IN
012. [01] 09021-00560 RACK ASSY, CONTROL
013. [01] 09024-40010 SCREW, AIR BLEEDER 09024-40010
014. [01] 09024-50310 SCREW, HOLLOW
015. [01] 09024-80010 WASHER, DRAIN SCRE 09024-80010
016. [02] 09025-10010 WASHER, INJECTION 85265-00077
017. [03] 09018-30090 PIN, INJECTION PUM
018. [03] 09023-00070 PLATE SET, VALVE H
019. [01] 09069-11020 BRACKET, STOP WIRE
020. [02] 94900-20500 SCREW, COUNTERSUNK
021. [03] 94900-75390 SCREW, W/WASHER
022. [03] 09013-90400 O-RING 47X0122600
023. [01] 09221-70590 NIPPLE, SWIVEL
024. [3C] 09031-10400 PLATE, TAPPET ADJU
024. [3C] 09031-10410 PLATE, TAPPET ADJU
024. [3C] 09031-10420 PLATE, TAPPET ADJU
024. [3C] 09031-10430 PLATE, TAPPET ADJU
024. [3C] 09031-10440 PLATE, TAPPET ADJU
024. [3C] 09031-10390 PLATE, TAPPET ADJU
024. [3C] 09031-10380 PLATE, TAPPET ADJU
024. [3C] 09031-10370 PLATE, TAPPET ADJU
024. [3C] 09031-10360 PLATE, TAPPET ADJU
024. [3C] 09031-10350 PLATE, TAPPET ADJU
024. [3C] 09031-10340 PLATE, TAPPET ADJU
024. [3C] 09031-10330 PLATE, TAPPET ADJU
024. [3C] 09031-10320 PLATE, TAPPET ADJU
024. [3C] 09031-10450 PLATE, TAPPET ADJU

Include in #3:

09450-08660 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09450-08660  30L6504300  PUMP ASSY, INJECTI
30L6504300    MITSUBISHI PUMP ASSY, INJECTI




Information:

3. Remove the connecting rod caps (1) from these pistons, and push the pistons upward until the rings clear the cylinder liner. 4. Remove the two pistons.5. Repeat Step 2 through 4 for the remaining pistons.Install Pistons
1. Thoroughly lubricate the crankshaft bearing journals and cylinder liners with clean SAE 30 engine oil.2. Lubricate the piston rings and connecting rod bearings with clean SAE 30 engine oil. 3. Using compressor (A), install the pistons with "V" mark on piston aligned with "V" mark on cylinder block. Guide the lower end of the rod over the crankshaft journal to prevent damage to the crankshaft.4. Lubricate the threads of cap retaining bolts with clean SAE 30 engine oil.5. Position the caps on the connecting rods, and install retaining nuts. Tighten nuts initially to 30 3 lb. ft. (4,1 0,4 mkg). Mark the nut and end of bolt, and tighten nut an additional 90° from mark.
When installing connecting rod cap, be sure that the number marked on side of cap is adjacent to and corresponds to the number marked on side of connecting rod.
6. Rotate the crankshaft until the next two bearing journals are at bottom dead center.7. Repeat Steps 2 through 5 for the remaining two pistons.concluding steps: a) install oil pumpb) install cylinder head assemblyDisassemble Pistons
preparatory step: a) remove pistons 1. Remove piston pin retaining rings (2).2. Remove piston pin (1) and remove piston from the connecting rod. 3. Remove the piston rings using ring expander (A).Assemble Pistons
1. Using ring expander (A), install the piston rings. The two compression rings are marked "UP - 1" and "UP - 2". The rings must be installed with these marks toward the top of the piston with "UP - 1" being the top ring. After all three rings have been installed on piston, stagger the ring caps 120° apart.2. Lubricate the piston pin with clean SAE 30 engine oil. 3. Position the piston on the connecting rod with the "V" mark (2) on the piston and number (1) on the connecting rod on the same side.4. Install the piston pin retaining rings. Make certain the retaining rings are seated in their grooves.concluding step: a) install pistons

Have questions with 09450-08660?





09450-08651 PUMP ASSY, INJECTI 09450-08650 09450-08640 09450-08600 09450-08590
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09450-08660

Back to top