Fuel injectors
  1. Home
  2. denso
  3. #09450-08530

09450-08530 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935003840
09450-08530 PUMP ASSY, INJECTI
Rating:
65
Buy PUMP ASSY, INJECTI 09450-08530 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09450-08530

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09450-08530 PUMP ASSY, INJECTI 30L6505500
001. [01] 09011-03730 HOUSING SUB-ASSY,
002. [03] 09013-00390 HOLDER SUB-ASSY, D 47X0119800
003. [03] 09013-60530 SPRING, DELIVERY V
004. [03] 09013-70130 GASKET, DELIVERY V
005. [03] 09014-02110 VALVE SUB-ASSY, IN
006. [03] 09015-04280 ELEMENT SUB-ASSY,
007. [03] 09016-00140 SLEEVE SUB-ASSY, C
008. [03] 09016-30140 SEAT, SPRING, UPR
009. [03] 09016-40220 SPRING, PUMP PLUNG MM501926
010. [03] 09016-50170 SEAT, SPRING, LWR
011. [03] 09017-00220 TAPPET SUB-ASSY,IN
012. [01] 09021-00560 RACK ASSY, CONTROL
013. [01] 09024-40010 SCREW, AIR BLEEDER 09024-40010
014. [01] 09024-50310 SCREW, HOLLOW
015. [01] 09024-80010 WASHER, DRAIN SCRE 09024-80010
016. [02] 09025-10010 WASHER, INJECTION 85265-00077
017. [03] 09018-30090 PIN, INJECTION PUM
018. [03] 09023-00070 PLATE SET, VALVE H
019. [01] 09069-11020 BRACKET, STOP WIRE
020. [02] 94900-20500 SCREW, COUNTERSUNK
021. [03] 94900-75390 SCREW, W/WASHER
022. [03] 09013-90400 O-RING 47X0122600
023. [01] 09221-70470 NIPPLE, SWIVEL
024. [3C] 09031-10400 PLATE, TAPPET ADJU
024. [3C] 09031-10410 PLATE, TAPPET ADJU
024. [3C] 09031-10420 PLATE, TAPPET ADJU
024. [3C] 09031-10430 PLATE, TAPPET ADJU
024. [3C] 09031-10440 PLATE, TAPPET ADJU
024. [3C] 09031-10390 PLATE, TAPPET ADJU
024. [3C] 09031-10380 PLATE, TAPPET ADJU
024. [3C] 09031-10370 PLATE, TAPPET ADJU
024. [3C] 09031-10360 PLATE, TAPPET ADJU
024. [3C] 09031-10350 PLATE, TAPPET ADJU
024. [3C] 09031-10340 PLATE, TAPPET ADJU
024. [3C] 09031-10330 PLATE, TAPPET ADJU
024. [3C] 09031-10320 PLATE, TAPPET ADJU
024. [3C] 09031-10450 PLATE, TAPPET ADJU

Include in #3:

09450-08530 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09450-08530  30L6505500  PUMP ASSY, INJECTI
30L6505500    MITSUBISHI PUMP ASSY, INJECTI




Information:


TIMING PIN HOLE PLUG (Typical Example)
1. Plug.2. Rotate the crankshaft CLOCKWISE (as viewed from front of engine) until the timing pin drops into the timing slot in the fuel injection pump camshaft.3. Disconnect wire (2) from fuel shut off solenoid.
WIRE AND HOUSING
2. Wire. 3. Tachometer drive adapter housing.4. Remove the tachometer drive adapter housing (3).5. Use ratchet (4) and socket (5) to loosen automatic timing advance unit from fuel injection pump camshaft. Back off retaining bolt. The bolt will feel loose, then tighten up again when taper starts to separate from the camshaft.
REMOVING RETAINING BOLT
4. 8H8572 Ratchet. 5. 8S2357 Deep Well Socket.6. Remove the plug from timing hole (7) in the front cover and insert bolt (6). The cover retaining bolt from hole (8) may be used.
INSTALLING BOLT
6. 1D4539 Bolt [5/16 in. - 18 NC, 2.5 in. (63,5 mm) long]. 7. Timing hole. 8. Hole.7. Rotate crankshaft CLOCKWISE (as viewed from front of engine) until bolt (6) threads into the timing gear and is centered in timing hole (7). With timing pin in slot in fuel pump camshaft and the bolt (6) through the front cover and threaded into the timing gear, the fuel injection pump camshaft is timed to the engine.8. Remove the fuel injection pump housing retaining bolts (9).
RETAINING BOLTS
9. Retaining bolts.9. Remove the fuel injection pump housing and governor as a unit.
REMOVING HOUSINGInstall Fuel Injection Pump Housing and Governor
1. Install the fuel injection pump housing and governor as a unit. Install the fuel injection pump housing retaining bolts.2. Install the automatic timing advance unit retaining bolt and tighten retaining bolt to 35 2 lb. ft. (4.8 0.3 mkg).3. To check timing remove the timing pin and the bolt. Rotate the crankshaft two revolutions CLOCKWISE (as viewed from front of engine) and install the timing pin and bolt back in place. If the timing pin or bolt can not be installed, the fuel injection pump camshaft must be retimed.4. Remove the bolt (6) from the timing gear and install in hole (8). Install the plug into timing hole (7).5. Remove the timing pin from the timing slot in the fuel injection pump camshaft and install the plug in the timing hole.6. Install the tachometer drive adapter housing. Connect the wire to the fuel shut off solenoid.Disassemble Max-Min Governor
MAX-MIN GOVERNOR DISASSEMBLED
1. Seal. 2. Link. 3. Yoke. 4. Coned disc washer. 5. Washer.Assemble Max-Min Governor
MAX-MIN GOVERNOR
1. Seal. 2. Link. 3. Yoke. 4. Coned disc washer. 5. Washer.Install seal (1) with lip facing toward inside of governor housing.Link (2) must turn freely on yoke (3).Install coned disc washer (4) with concave side toward washer (5). The 1160 Engines, 5.0 in. (127.0 mm) stroke, do not have washer (4).
After disassembly and assembly, use the following initial settings to protect the engine from overspeed.
Disassemble Hydraulic Governor (9L9540 Governor)
HYDRAULIC GOVERNOR DISASSEMBLED
1. Seal. 2. Seal. 3. Weights.Assemble Hydraulic Governor (9L9540 Governor)
HYDRAULIC GOVERNOR
1. Seal. 2. Seal. 3. Weights.Lubricate seal (1) and all adjoining surfaces with clean engine oil (SAE 30).Install seal (2)

Have questions with 09450-08530?





09450-08520 PUMP ASSY, INJECTI 09450-08510 09450-08500 09450-08490 09450-08480
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09450-08530

Back to top