Fuel injectors
  1. Home
  2. denso
  3. #09450-07450

09450-07450 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935003840
09450-07450 PUMP ASSY, INJECTI
Rating:
2
Buy PUMP ASSY, INJECTI 09450-07450 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09450-07450

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09450-07450 PUMP ASSY, INJECTI 31A6504050
005. [01] 09011-05070 HOUSING SUB-ASSY, 47X0104200
006. [04] 09013-10520 HOLDER, DELIVERY V
007. [04] 09013-60640 SPRING, DELIVERY V
008. [04] 09013-70130 GASKET, DELIVERY V
009. [04] 09014-02710 VALVE SUB-ASSY, IN 47X0114400
010. [04] 09015-05450 ELEMENT SUB-ASSY, 47X0104400
011. [04] 09016-10210 SLEEVE, PLUNGER CO
012. [04] 09016-30082 SEAT, SPRING, UPR MM501098
013. [04] 09016-40170 SPRING, PUMP PLUNG
014. [04] 09017-00170 TAPPET SUB-ASSY,IN EZ01775027
014-001. [04] 09017-10022 TAPPET, INJECTION
014-002. [04] 09217-60010 ROLLER, FEED PUMP 09217-60010
014-003. [04] 09017-60020 PIN, INJECTION PUM
015. [04] 09018-30050 PIN, INJECTION PUM
016. [01] 09021-00440 RACK ASSY, CONTROL
017. [04] 09030-10060 SEAT, SPRING, LWR EZ0177514
018. [02] 09046-70030 PLATE
019. [4C] 09031-10010 PLATE, TAPPET ADJU 09031-10010
019. [4C] 09031-10310 PLATE, TAPPET ADJU
019. [4C] 09031-10300 PLATE, TAPPET ADJU
019. [4C] 09031-10280 PLATE, TAPPET ADJU
019. [4C] 09031-10170 PLATE, TAPPET ADJU FR51530028
019. [4C] 09031-10160 PLATE, TAPPET ADJU FR51530027
019. [4C] 09031-10140 PLATE, TAPPET ADJU 09031-10140
019. [4C] 09031-10130 PLATE, TAPPET ADJU 09031-10130
019. [4C] 09031-10120 PLATE, TAPPET ADJU 09031-10120
019. [4C] 09031-10110 PLATE, TAPPET ADJU 09031-10110
020. [01] 94901-81020 WASHER, COPPER PLA 94901-81020
021. [01] 09024-40180 SCREW, AIR BLEEDER
022. [01] 94918-00310 SCREW, HOLLOW 85265-00078
023. [03] 09006-80020 PLATE, ADJUSTING
024. [03] 94904-80800 BOLT, WASHER HEAD MM514195
025. [04] 90802-20150 O-RING
025. [04] 09013-90410 O-RING 47X0122700

Include in #3:

09450-07450 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09450-07450  31A6504050  PUMP ASSY, INJECTI
31A6504050    MITSUBISHI PUMP ASSY, INJECTI




Information:

3. Install tool (A) and remove the cylinder liners. 4. Remove filler band (1) and O-ring seals (2) from the cylinder liners.Install Cylinder Liners
1. Clean the cylinder liners and cylinder block. 2. Install the liners (1) in the cylinder block without the O-ring seals and filler bands. See CYLINDER LINER PROJECTION in TESTING AND ADJUSTING. 3. Install tooling (A) and two 5/8" - 11 NC bolts 5 1/2 in. long. Tighten the bolts evenly to 50 lb.ft. (70 N m).4. Check the liner projection with tool (B) at four locations around the liner.5. Liner projection must be .0020 to .0056 in. (0.051 to 0.142 mm). Measurements on the same liner must not be different by more than .002 in. (0.05 mm). Average measurement between liners next to each other must not be different by more than .002 in. (0.05 mm). The maximum permissible difference between average projection of all cylinder liners under one cylinder head is .004 in. (0.10 mm). The liner projection can change if the liner is turned in the bore. 6. If the liner projection is not .0020 to .0056 in. (0.051 to 0.142 mm), check the thickness of the liner flange (2) and the depth of the liner bore in the cylinder block. The thickness of the liner flange (2) must be .4048 .0008 in. (10.282 0.020 mm).7. The depth of the liner bore in the cylinder block must be .401 .001 in. (10.19 0.03 mm). If the liner bore in the block is worn and the measurement is not correct, the liner bore can be corrected with a cylinder block counterboring tool. See SPECIAL INSTRUCTIONS, FORM FM055228.8. Put a mark on the liner and cylinder block so the liner can be installed in the same position from which it was removed. 9. Install new O-ring seals (4) on the cylinder liners. Put liquid soap on the O-ring seals and in the bases in the cylinder block.
The liners must be installed in the cylinder block immediately after filler band (3) is installed. Make sure the marks on the liners and the cylinder block are in alignment when the cylinder liners are installed.
10. Put (dip) the filler band completely in clean SAE 30 oil and install it on the liner immediately.11. Install the liner in the cylinder block immediately with tooling (C).end by:a) install pistons

Have questions with 09450-07450?





09450-07440 PUMP ASSY, INJECTI 09450-07430 09450-07420 09450-07410 09450-07400
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09450-07450

Back to top