Fuel injectors
  1. Home
  2. denso
  3. #09450-07080

09450-07080 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935003840
09450-07080 PUMP ASSY, INJECTI
Rating:
77
Buy PUMP ASSY, INJECTI 09450-07080 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09450-07080

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09450-07080 PUMP ASSY, INJECTI 31A6502050
005. [01] 09011-05070 HOUSING SUB-ASSY, 47X0104200
006. [04] 09013-10520 HOLDER, DELIVERY V
007. [04] 09013-60540 SPRING, DELIVERY V
008. [04] 09013-70130 GASKET, DELIVERY V
009. [04] 09014-02610 VALVE SUB-ASSY, IN 47X0107700
010. [04] 09015-05550 ELEMENT SUB-ASSY, 47X0105400
011. [04] 09016-10210 SLEEVE, PLUNGER CO
012. [04] 09016-30082 SEAT, SPRING, UPR MM501098
013. [04] 09016-40170 SPRING, PUMP PLUNG
014. [04] 09017-00170 TAPPET SUB-ASSY,IN EZ01775027
014-001. [04] 09017-10022 TAPPET, INJECTION
014-002. [04] 09217-60010 ROLLER, FEED PUMP 09217-60010
014-003. [04] 09017-60020 PIN, INJECTION PUM
015. [04] 09018-30050 PIN, INJECTION PUM
016. [01] 09021-00440 RACK ASSY, CONTROL
017. [04] 09030-10060 SEAT, SPRING, LWR EZ0177514
018. [02] 09046-70030 PLATE
019. [4C] 09031-10310 PLATE, TAPPET ADJU
019. [4C] 09031-10300 PLATE, TAPPET ADJU
019. [4C] 09031-10280 PLATE, TAPPET ADJU
019. [4C] 09031-10170 PLATE, TAPPET ADJU FR51530028
019. [4C] 09031-10160 PLATE, TAPPET ADJU FR51530027
019. [4C] 09031-10140 PLATE, TAPPET ADJU 09031-10140
019. [4C] 09031-10130 PLATE, TAPPET ADJU 09031-10130
019. [4C] 09031-10120 PLATE, TAPPET ADJU 09031-10120
019. [4C] 09031-10110 PLATE, TAPPET ADJU 09031-10110
019. [4C] 09031-10010 PLATE, TAPPET ADJU 09031-10010
020. [01] 94901-81020 WASHER, COPPER PLA 94901-81020
020. [01] 09022-20080 WASHER, FUEL PIPE MM500114
021. [01] 09024-40180 SCREW, AIR BLEEDER
022. [01] 94918-00310 SCREW, HOLLOW 85265-00078
023. [03] 09006-80020 PLATE, ADJUSTING
024. [03] 94904-80800 BOLT, WASHER HEAD MM514195
025. [04] 90802-20150 O-RING
025. [04] 09013-90410 O-RING 47X0122700

Include in #3:

09450-07080 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09450-07080  31A6502050  PUMP ASSY, INJECTI
31A6502050    MITSUBISHI PUMP ASSY, INJECTI




Information:

start by:a) remove pistons 1. Remove bearings (3) from the connecting rod and connecting rod cap.2. Remove retainer ring (1) with tool (A).3. Remove pin (2) and connecting rod (4) from the piston. 4. Remove the piston rings (5) from the piston with tool (B). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning tool. See USE OF PISTON PIN BEARING REMOVAL AND INSTALLATION TOOLS, SPECIAL INSTRUCTIONS, Form No. SMHS7295.5. Heat the connecting rod (4) in an oven to a temperature of 350°-500°F (177°-260°C). Never use a direct flame to heat a connecting rod. 6. Put connecting rod (4) in position on the base plate of tooling (C). Put a new rod pin bearing (6) on the adapter part of tooling (C). The old bearing is pushed out by tooling (C) as the new bearing is installed.7. Use tooling (C) to push the new bearing into the connecting rod until the push adapter of tooling (C) makes full contact with the connecting rod surface.8. Use a pin boring machine to make the rod pin bearing the correct size. The bore in the new rod pin bearing must be 2.0012 .0003 in. (50.830 0.008 mm).9. Check the clearance between the ends of the piston rings. See PISTONS AND RINGS in SPECIFICATIONS.10. Install the oil ring spring in the oil ring groove of the piston. The oil ring is to be installed over the spring with the oil ring end gap 180° from the oil ring spring joint. 11. Install the oil ring on the piston with tool (B).12. Install the second (intermediate) piston ring with the side that has the identification "UP-2" toward the top of the piston with tool (B).13. Install the first (top) piston ring with the side that has the identification "UP-1" toward the top of the piston with tool (B). After the installation of all three piston rings, put the piston rings in position so the end gaps are 120° apart. 14. Put the piston in position on connecting rod (4). Put clean engine oil on pin (2) and install the pin. Install retainer rings (1) with tool (A). Make sure the retainer rings are in the grooves of the piston.15. Install bearings (3) in the connecting rod and connecting rod cap.end by:a) install pistons

Have questions with 09450-07080?





09450-07060 PUMP ASSY, INJECTI 09450-07050 09450-07040 09450-07030 09450-07020
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09450-07080

Back to top