Fuel injectors
  1. Home
  2. denso
  3. #09450-06920

09450-06920 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935003840
09450-06920 PUMP ASSY, INJECTI
Rating:
24
Buy PUMP ASSY, INJECTI 09450-06920 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09450-06920

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09450-06920 PUMP ASSY, INJECTI 31A6502030
005. [01] 09011-05070 HOUSING SUB-ASSY, 47X0104200
006. [04] 09013-10520 HOLDER, DELIVERY V
007. [04] 09013-60640 SPRING, DELIVERY V
008. [04] 09013-70130 GASKET, DELIVERY V
009. [04] 09014-02610 VALVE SUB-ASSY, IN 47X0107700
010. [04] 09015-02400 ELEMENT SUB-ASSY,
011. [04] 09016-10210 SLEEVE, PLUNGER CO
012. [04] 09016-30082 SEAT, SPRING, UPR MM501098
013. [04] 09016-40170 SPRING, PUMP PLUNG
014. [04] 09017-00170 TAPPET SUB-ASSY,IN EZ01775027
014-001. [04] 09017-10021 TAPPET, INJECTION
014-002. [04] 09217-60010 ROLLER, FEED PUMP 09217-60010
014-003. [04] 09017-60020 PIN, INJECTION PUM
015. [04] 09018-30050 PIN, INJECTION PUM
016. [01] 09021-00440 RACK ASSY, CONTROL
017. [04] 09030-10060 SEAT, SPRING, LWR EZ0177514
018. [02] 09046-70030 PLATE
019. [4C] 09031-10310 PLATE, TAPPET ADJU
019. [4C] 09031-10300 PLATE, TAPPET ADJU
019. [4C] 09031-10280 PLATE, TAPPET ADJU
019. [4C] 09031-10170 PLATE, TAPPET ADJU FR51530028
019. [4C] 09031-10160 PLATE, TAPPET ADJU FR51530027
019. [4C] 09031-10140 PLATE, TAPPET ADJU 09031-10140
019. [4C] 09031-10130 PLATE, TAPPET ADJU 09031-10130
019. [4C] 09031-10120 PLATE, TAPPET ADJU 09031-10120
019. [4C] 09031-10110 PLATE, TAPPET ADJU 09031-10110
019. [4C] 09031-10010 PLATE, TAPPET ADJU 09031-10010
020. [02] 94901-81020 WASHER, COPPER PLA 94901-81020
020. [02] 09022-20080 WASHER, FUEL PIPE MM500114
021. [02] 09024-40180 SCREW, AIR BLEEDER
022. [01] 94918-00510 SCREW, HOLLOW MM500083
023. [03] 09006-80020 PLATE, ADJUSTING
024. [03] 94904-80800 BOLT, WASHER HEAD MM514195
027. [04] 90802-20150 O-RING
027. [04] 09013-90410 O-RING 47X0122700

Include in #3:

09450-06920 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09450-06920  31A6502030  PUMP ASSY, INJECTI
31A6502030    MITSUBISHI PUMP ASSY, INJECTI




Information:

3. Remove bearing caps (1) from the two connecting rods. Put pieces of rubber hose or tape on the threads of the connecting rod bolts as protection for the crankshaft. 4. Push the pistons up until the piston rings are clear of the cylinder liner. Remove pistons (2). Keep each cap with its connecting rod.
Do not turn the crankshaft while any of the connecting rods are in the engine without the caps installed. Do not cause damage to the cooling tubes when the pistons are removed.
5. Do Steps 1 through 4 for the remainder of the pistons.Install Pistons
1. Put clean engine oil on the piston rings and cylinder liners. 2. Put two pistons in position opposite of each other in the correct bore of the block. Install pistons (1) with tool (A).
Make sure that the pistons are installed with flat surfaces (2) of the connecting rods toward each other and the chamfered sides (4) toward the crankshaft.
For more detail about the installation of connecting rod bearings see REMOVE AND INSTALL CONNECTING ROD BEARINGS.3. Check the bearing clearances with tool (B). 4. Put clean engine oil on bolts (5) and the connecting rod bearings. Install caps (3) and nuts finger tight. Tighten each nut to a torque of 60 6 lb.ft. (80 8 N m). Put a mark across the nuts and bolts. Tighten each nut 120° more.5. Check the side clearance between two connecting rods on the same crankshaft journal. Clearance must be .011 to .033 in. (0.28 to 0.84 mm) for new rods.6. Do Steps 1 through 5 for the remainder of the pistons.

Have questions with 09450-06920?





09450-06910 PUMP ASSY, INJECTI 09450-06900 09450-06890 09450-06880 09450-06870
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09450-06920

Back to top