Fuel injectors
  1. Home
  2. denso
  3. #09450-06820

09450-06820 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935003840
09450-06820 PUMP ASSY, INJECTI
Rating:
2
Buy PUMP ASSY, INJECTI 09450-06820 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09450-06820

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09450-06820 PUMP ASSY, INJECTI 31B6502030
005. [01] 09011-05110 HOUSING SUB-ASSY, 47X0106100
006. [03] 09013-10520 HOLDER, DELIVERY V
007. [03] 09013-60540 SPRING, DELIVERY V
008. [03] 09013-70130 GASKET, DELIVERY V
009. [03] 09014-02610 VALVE SUB-ASSY, IN 47X0107700
010. [03] 09015-05550 ELEMENT SUB-ASSY, 47X0105400
011. [03] 09016-10210 SLEEVE, PLUNGER CO
012. [03] 09016-30082 SEAT, SPRING, UPR MM501098
013. [03] 09016-40170 SPRING, PUMP PLUNG
014. [03] 09017-00170 TAPPET SUB-ASSY,IN EZ01775027
014-001. [03] 09017-10021 TAPPET, INJECTION
014-002. [03] 09217-60010 ROLLER, FEED PUMP 09217-60010
014-003. [03] 09017-60020 PIN, INJECTION PUM
015. [03] 09018-30050 PIN, INJECTION PUM
016. [01] 09021-00470 RACK ASSY, CONTROL
017. [03] 09030-10060 SEAT, SPRING, LWR EZ0177514
018. [01] 09046-70040 PLATE
019. [3C] 09031-10310 PLATE, TAPPET ADJU
019. [3C] 09031-10300 PLATE, TAPPET ADJU
019. [3C] 09031-10280 PLATE, TAPPET ADJU
019. [3C] 09031-10170 PLATE, TAPPET ADJU FR51530028
019. [3C] 09031-10160 PLATE, TAPPET ADJU FR51530027
019. [3C] 09031-10140 PLATE, TAPPET ADJU 09031-10140
019. [3C] 09031-10130 PLATE, TAPPET ADJU 09031-10130
019. [3C] 09031-10120 PLATE, TAPPET ADJU 09031-10120
019. [3C] 09031-10110 PLATE, TAPPET ADJU 09031-10110
019. [3C] 09031-10010 PLATE, TAPPET ADJU 09031-10010
020. [01] 94901-81020 WASHER, COPPER PLA 94901-81020
020. [01] 09022-20080 WASHER, FUEL PIPE MM500114
021. [01] 09024-40180 SCREW, AIR BLEEDER
022. [01] 09024-50210 SCREW, HOLLOW
023. [02] 09006-80020 PLATE, ADJUSTING
024. [02] 94904-80800 BOLT, WASHER HEAD MM514195
027. [03] 90802-20150 O-RING
027. [03] 09013-90410 O-RING 47X0122700

Include in #3:

09450-06820 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09450-06820  31B6502030  PUMP ASSY, INJECTI
31B6502030    MITSUBISHI PUMP ASSY, INJECTI




Information:

1. Remove bolt (4). Remove lever (5) and the rod from the governor.2. Remove lockwire (2). Remove bolts (1) and cover (3) from the governor housing. Check the condition of the gasket under the cover. If the gasket has damage, use a new part for replacement. 3. Remove the bolt from stop collar (6). Remove stop collar (6). Remove the collar and spring from below collar (6). 4. Install tool (A) in the fuel injection pump housing. Make sure the correct end of tool (A) is used. Tool (A) is in position when it is against the shoulder of the groove in the rack. The racks are now in the center (zero) position.5. Remove bolts (8) and governor housing (7). 6. Disconnect fuel lines (11) from the governor plate.7. Remove bolts (10) and governor plate (9). Check the condition of the gasket under the plate. If the gasket has damage, use a new part for replacement. It is possible to remove the governor and governor plate as a unit. The above steps must be followed before the governor can be installed again on the injection pump housing.Install Governor (Earlier)
The driver assembly must be removed from the governor plate before the governor plate is installed in the injection pump housing.
1. Install a new gasket on the injection pump housing. 2. Put governor plate (1) in position on the fuel pump housing. Make sure the dowels in governor plate (1) are in alignment with the holes in the injection pump housing. The racks must be held against the rack stop pin and the governor lever engaged in the groove (slot) in the left hand rack. 3. Install stop (3) in gear (4). Make sure the wide space in stop (3) is in alignment with the wide space on the drive pinion assembly.4. Install drive gear assembly (2). 5. Make an alignment of the holes in gear (4), the stop and drive assembly. Install the pin and ring (5) that hold the unit together. 6. Install the gasket and governor housing (8) on the governor plate.7. Install the spring, collar and stop collar (7). Install the bolt in the collar to hold it.8. Check the governor adjustment. See GOVERNOR ADJUSTMENTS in TESTING AND ADJUSTING.9. Install the gasket and cover (6) on the governor housing. Make sure the dowel in the cover is in alignment with the notch in collar (7). Install the bolts that hold the cover in position. Install a new lockwire.10. Connect the fuel lines to the governor plate.11. Install the lever for the governor control.12. Remove tool (A) from the injection pump housing.end by:a) install fuel ratio control

Have questions with 09450-06820?





09450-06810 PUMP ASSY, INJECTI 09450-06800 09450-06790 09450-06780 09450-06771
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09450-06820

Back to top