Information pump assy, injecti
Nozzle:
0935004540
Rating:
Components :
| 001. | PUMP ASSY, INJECTI | 09450-06290 |
Scheme ###:
| 000. | [01] | 09450-06290 | PUMP ASSY, INJECTI | 17298-51012 |
| 001. | [01] | 09011-01161 | HOUSING SUB-ASSY, | 15321-51081 |
| 002. | [03] | 09013-00450 | HOLDER SUB-ASSY, D | 16415-51221 |
| 003. | [03] | 09013-60970 | SPRING, DELIVERY V | 16475-51231 |
| 004. | [03] | 09013-70130 | GASKET, DELIVERY V | 11420-51241 |
| 005. | [03] | 09014-02050 | VALVE SUB-ASSY, IN | 16475-51031 |
| 006. | [03] | 09015-05130 | ELEMENT SUB-ASSY, | |
| 008. | [03] | 09016-30082 | SEAT, SPRING, UPR | 15221-51271 |
| 009. | [03] | 09016-40170 | SPRING, PUMP PLUNG | 15221-51281 |
| 010. | [03] | 09016-10210 | SLEEVE, PLUNGER CO | 15221-51382 |
| 011. | [03] | 09017-00170 | TAPPET SUB-ASSY,IN | 15221-51071 |
| 011-001. | [03] | 09017-10021 | TAPPET, INJECTION | 15021-51990 |
| 011-002. | [03] | 09217-60010 | ROLLER, FEED PUMP | 15109-52931 |
| 011-003. | [03] | 09017-60020 | PIN, INJECTION PUM | 15021-51970 |
| 012. | [01] | 09021-00220 | RACK ASSY, CONTROL | 15321-51061 |
| 015. | [01] | 09024-50160 | SCREW, HOLLOW | 15521-51321 |
| 016. | [02] | 09024-10010 | WASHER, AIR BLEEDE | 15221-96651 |
| 017. | [03] | 09018-30050 | PIN, INJECTION PUM | 14611-51251 |
| 018. | [03] | 09030-10060 | SEAT, SPRING, LWR | 15021-51291 |
| 019. | [01] | 09046-70040 | PLATE | 19484-51461 |
| 020. | [02] | 09006-80020 | PLATE, ADJUSTING | 14384-51391 |
| 021. | [02] | 94904-80800 | BOLT, WASHER HEAD | |
| 022. | [03] | 90802-20150 | O-RING | 14611-51201 |
| 024. | [3C] | 09031-10530 | PLATE, TAPPET ADJU | |
| 024. | [3C] | 09031-10520 | PLATE, TAPPET ADJU | |
| 024. | [3C] | 09031-10510 | PLATE, TAPPET ADJU | |
| 024. | [3C] | 09031-10500 | PLATE, TAPPET ADJU | |
| 024. | [3C] | 09031-10490 | PLATE, TAPPET ADJU | |
| 024. | [3C] | 09031-10060 | PLATE, TAPPET ADJU | |
| 024. | [3C] | 09031-10050 | PLATE, TAPPET ADJU | |
| 024. | [3C] | 09031-10040 | PLATE, TAPPET ADJU | |
| 024. | [3C] | 09031-10030 | PLATE, TAPPET ADJU | |
| 024. | [3C] | 09031-10020 | PLATE, TAPPET ADJU | |
| 025. | [01] | 09023-10070 | PLATE, DELIVERY VA | |
| 026. | [01] | 09023-20070 | PLATE, DELIVERY VA | |
| 029. | [02] | 94904-44330 | BOLT |
Include in #3:
09450-06290
as PUMP ASSY, INJECTI
Cross reference number
| Part num | Firm num | Firm | Name |
| 09450-06290 | 17298-5101 | PUMP ASSY, INJECTI | |
| 17298-51012 | KUBOTA | PUMP ASSY, INJECTI |
Information:
(10) Distance from top surface of housing to top of lower governor drive bearing ... 28.4 0.5 mm (1.12 .02 in.)(11) Install top governor drive bearing (notch end up) with sharp corner even with top surface of housing. Position center of notch so that it is in alignment with the center of oil pressure relief hole (Z) by an amount of ... 10°(12) Install dowel to get a dimension from centerline of fuel injection pump bore to dowel (seal dowel holes with aluminum ball) ... 14.76 0.10 mm (.581 .004 in.)(13) Distance from end of bearing to face of boss on housing ... 73.03 0.51 mm (2.875 .020 in.)(14) Distance between the bearings for the shaft ... 34.80 0.51 mm (1.370 .020 in.)(15) Install pins until they contact bottom of housing casting.