Fuel injectors
  1. Home
  2. denso
  3. #09450-05000

09450-05000 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935003840
09450-05000 PUMP ASSY, INJECTI
Rating:
22
Buy PUMP ASSY, INJECTI 09450-05000 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09450-05000

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09450-05000 PUMP ASSY, INJECTI MM437670
003. [01] 09011-03730 HOUSING SUB-ASSY, MM501917
004. [03] 09013-10830 HOLDER, DELIVERY V MM501918
005. [03] 09013-60820 SPRING, DELIVERY V MM501919
006. [03] 09013-70130 GASKET, DELIVERY V MM501856
006. [03] 09013-70061 GASKET, DELIVERY V P720-16141
007. [03] 09014-02040 VALVE SUB-ASSY, IN MM514138
008. [03] 09015-04280 ELEMENT SUB-ASSY, MM514078
010. [03] 09016-00140 SLEEVE SUB-ASSY, C MM501999
011. [03] 09016-30140 SEAT, SPRING, UPR
012. [03] 09016-40220 SPRING, PUMP PLUNG
013. [03] 09016-50170 SEAT, SPRING, LWR
014. [03] 09017-00220 TAPPET SUB-ASSY,IN
015. [01] 09021-00560 RACK ASSY, CONTROL MM501929
016. [01] 09024-40010 SCREW, AIR BLEEDER MM501930
017. [01] 09024-50240 SCREW, HOLLOW
018. [01] 09024-80010 WASHER, DRAIN SCRE ME702175
019. [02] 09025-10010 WASHER, INJECTION ME702595
020. [02] 94900-20500 SCREW, COUNTERSUNK MM501935
021. [01] 09069-11020 BRACKET, STOP WIRE MM501934
022. [03] 09013-90400 O-RING
022. [03] 90801-10130 O-RING ME703339
023. [3C] 09031-10450 PLATE, TAPPET ADJU MM501952
023. [3C] 09031-10440 PLATE, TAPPET ADJU MM501951
023. [3C] 09031-10430 PLATE, TAPPET ADJU MM501950
023. [3C] 09031-10420 PLATE, TAPPET ADJU MM501949
023. [3C] 09031-10410 PLATE, TAPPET ADJU MM501948
023. [3C] 09031-10400 PLATE, TAPPET ADJU MM501947
023. [3C] 09031-10390 PLATE, TAPPET ADJU MM501946
023. [3C] 09031-10380 PLATE, TAPPET ADJU MM501945
023. [3C] 09031-10320 PLATE, TAPPET ADJU
023. [3C] 09031-10330 PLATE, TAPPET ADJU
023. [3C] 09031-10340 PLATE, TAPPET ADJU MM501941
023. [3C] 09031-10350 PLATE, TAPPET ADJU MM501942
023. [3C] 09031-10360 PLATE, TAPPET ADJU MM501943
023. [3C] 09031-10370 PLATE, TAPPET ADJU MM501944
025. [01] 09221-70480 NIPPLE, SWIVEL MM501982
026. [03] 91370-05101 SCREW, W/WASHER MZ701679
026. [03] 94900-75390 SCREW, W/WASHER MM514190
027. [03] 09023-00070 PLATE SET, VALVE H MM501933
028. [03] 09018-30090 PIN, INJECTION PUM MM501932

Include in #3:

09450-05000 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09450-05000  MM437670  PUMP ASSY, INJECTI
MM437670    MITSUBISHI PUMP ASSY, INJECTI




Information:

2. Remove the bolts (1) and water lines (2).3. Loosen the drive belts (4).4. Remove the bolts (3) that hold water pump to cylinder block.5. Remove the water pump.Install Water Pump
1. Put the water pump into position on engine, and install the bolts.2. Put the two water lines in position, and install the four bolts.3. Install the drive belts and tighten them to the tension given in OPERATION AND MAINTENANCE GUIDE.4. Fill the cooling system.Disassemble Water Pump
start by: a) remove water pump 1. Remove nut (1) and lock from shaft. Remove the pulley (2) from shaft.2. Remove bolts (3) from housings, and pull the housings (4) and (5) apart.3. Remove the lip-type seal from housing (4).4. Remove the ring for seal from pulley (2). 5. Lift the shaft (6) out of housing (5). 6. Remove cotter pin, nut (10), and washer. Remove the impeller (8).7. Remove bolts (7) and locks, and remove the housing (9) from shaft. 8. Remove seals (11) and (12) from housing (9).9. Remove the key, two bearings, spacer, and plate from shaft (6).Assemble Water Pump
1. Use tool setup (A) to install the seal in housing (1) with lip of seal toward impeller side of housing. Put oil on lip of seal. 2. Heat the bearings (3) and (6) in oil at a maximum temperature of 275°F (135°C).3. Install bearing (3), plate (4), spacer (5), bearing (6), and key (7) on shaft (2).4. Put housing (1) in position on shaft (2). Install the four bolts (10) and two locks.5. Install the seal and ring in housing (1) with the shiny surface of ring toward impeller. 6. Put the seal assembly in position on shaft, and install the impeller (9). Install washer and nut (8). Tighten the nut to 30 5 lb.ft. (4.1 0.7 mkg) plus amount needed to install the cotter pin.7. Put the shaft, housing, and impeller in position in housing (11). 8. Use tool setup (B) to install seal in housing (13) with lip of seal toward pulley. Install the ring for seal on pulley (15). Put oil on lip of seal.9. Put housing (13) in position, and install the bolts (12). Install pulley (15), lock, and nut (14). Tighten nut to 55 lb.ft. (7.6 mkg) and bend the lock.end by: a) install water pump

Have questions with 09450-05000?





09450-04990 PUMP ASSY, INJECTI 09450-04980 09450-04970 09450-04960 09450-04950
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09450-05000

Back to top