Fuel injectors
  1. Home
  2. denso
  3. #09450-03181

09450-03181 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09450-03181 PUMP ASSY, INJECTI
Rating:
73
Buy PUMP ASSY, INJECTI 09450-03181 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09450-03181

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09450-03181 PUMP ASSY, INJECTI 14287-51011
001. [01] 09011-02300 HOUSING SUB-ASSY, 14287-51081
001. [01] 09011-05320 HOUSING SUB-ASSY,
001. [01] 09011-02300 HOUSING SUB-ASSY, 14287-51081
002. [01] 09013-10280 HOLDER, DELIVERY V 15601-51221
002. [01] 09013-10520 HOLDER, DELIVERY V
003. [01] 09013-60230 SPRING, DELIVERY V 15221-51231
004. [01] 09013-70061 GASKET, DELIVERY V 15221-51241
004. [01] 09013-70130 GASKET, DELIVERY V 11420-51241
005. [01] 09014-00410 VALVE SUB-ASSY, IN 15221-51031
006. [01] 09015-01790 ELEMENT SUB-ASSY, 14911-51051
008. [01] 09016-30082 SEAT, SPRING, UPR 15221-51271
009. [01] 09016-40170 SPRING, PUMP PLUNG 15221-51281
010. [01] 09016-10210 SLEEVE, PLUNGER CO 15221-51382
011. [01] 09017-00170 TAPPET SUB-ASSY,IN 15221-51071
011-001. [01] 09017-10022 TAPPET, INJECTION 15021-51990
011-002. [01] 09217-60010 ROLLER, FEED PUMP 15109-52931
011-003. [01] 09017-60020 PIN, INJECTION PUM 15021-51970
012. [01] 09021-00342 RACK ASSY, CONTROL 14911-51061
015. [01] 09062-40060 UNION, VENTURI PIP
016. [01] 09024-10010 WASHER, AIR BLEEDE 15221-96651
017. [01] 09018-30041 PIN, INJECTION PUM 15221-51251
017. [01] 09018-30130 PIN, INJECTION PUM
018. [01] 09030-10060 SEAT, SPRING, LWR 15021-51291
019. [01] 94907-20830 RING, SNAP 14911-51431
020. [01] 09013-90410 O-RING
020. [01] 90802-20150 O-RING 14611-51201
022. [ C] 09031-10300 PLATE, TAPPET ADJU
022. [ C] 09031-10280 PLATE, TAPPET ADJU
022. [ C] 09031-10170 PLATE, TAPPET ADJU
022. [ C] 09031-10160 PLATE, TAPPET ADJU
022. [ C] 09031-10140 PLATE, TAPPET ADJU
022. [ C] 09031-10130 PLATE, TAPPET ADJU 15221-51491
022. [ C] 09031-10120 PLATE, TAPPET ADJU
022. [ C] 09031-10110 PLATE, TAPPET ADJU
022. [ C] 09031-10010 PLATE, TAPPET ADJU 14109-51301
022. [ C] 09031-10310 PLATE, TAPPET ADJU

Include in #3:

09450-03181 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09450-03181  14287-5101  PUMP ASSY, INJECTI




Information:

Introduction
This Special Instruction provides detailed instructions on the installation of the sleeve into the compensator group of the 3408E and 3412E Unit Injector Hydraulic Pump. If leaks are experienced at the joint of the compensator and the adapter block, the 174-8943 Sleeve may be installed to improve sealing. The new press fit sleeve contains the O-ring more securely than the original slip fit sleeve.Note: Engines built prior to the serial number break that contain the new sleeve have a "S" stamped at the end of the part number on the serial number plate of the pump. The reworked part numbers appear as "144-0835-06S". Individual Components
Table 1
Quantity     Part Number     Part Description    
1     174-8943     Sleeve    
1     135-2652     O-Ring    
1     033-6039     O-Ring    
6     9X-7680     O-Ring    Necessary Tools
One of the following tools may be used to insert the new sleeve into the compensator group.
A 31.750 mm (1.250 inch) diameter flat plate.
The 1P-0467 Drive Plate from 1P-0510 Driver Group .
An acceptable bearing insertion tool.Removal Of The O-Ring Seals
Illustration 1 g00638376
Remove the four bolts (1) from the compensator (2). Remove the compensator and the adapter. Do not adjust the compensator. Refer to Special Instruction, REHS0192-03, step 3 of procedure for "Disassembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 2 g00638368
Remove the four O-ring seals (3) from the bottom side of the adapter. Refer to Special Instruction, REHS0192-03, step 4 of procedure for "Disassembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 3 g00638372
Remove the four O-ring seals (4) from the two housings. Refer to Special Instruction, REHS0192-03, step 5 of procedure for "Disassembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Remove the slip fit sleeve from the compensator housing.Installation Of The Sleeve
Illustration 4 g00637918
(1) Compensator assembly. (2) 174-8943 Sleeve .
Invert the compensator assembly (1). Hold the compensator assembly securely within a vise or a press table.
Start the sleeve (2) by hand into the compensator assembly (1) .Note: It is important that the groove on the outside diameter of the sleeve is oriented toward the O-ring in the joint. If this is not done, there will not be sufficient room to properly seal the O-ring.
Press the sleeve (2) flush with the surface of the compensator assembly (1) using the 1P-0467 Drive Plate or by using an acceptable bearing insertion tool.Installation Of The O-Ring Seals
Illustration 5 g00638368
Install the four O-ring seals (3) on the bottom side of the adapter. Refer to Special Instruction, REHS0192-03, step 16 of procedure for "Assembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 6 g00638372
Install the four O-rings (4) on the two housings. Refer to Special Instruction, REHS0192-03, step 17 of procedure for "Assembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 7 g00638376
Install the compensator assembly (2) and the adapter as a unit vertically so that the O-rings seals are not damaged. Tighten the four bolts (1) to the following torque.Torque for bolts ... 8 1 N

Have questions with 09450-03181?





09450-03170 PUMP ASSY, INJECTI 09450-03160 09450-03150 09450-03140 09450-03121
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09450-03181

Back to top