Fuel injectors
  1. Home
  2. denso
  3. #09450-02120

09450-02120 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935001660
09450-02120 PUMP ASSY, INJECTI
Rating:
15
Buy PUMP ASSY, INJECTI 09450-02120 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09450-02120

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09450-02120 PUMP ASSY, INJECTI MM409260
005. [01] 09011-02420 HOUSING SUB-ASSY, MM501253
006. [04] 09013-10280 HOLDER, DELIVERY V MM501075
006. [04] 09013-10520 HOLDER, DELIVERY V MM501507
007. [04] 09013-60540 SPRING, DELIVERY V MM501161
008. [04] 09013-70061 GASKET, DELIVERY V P720-16141
008. [04] 09013-70130 GASKET, DELIVERY V MM501856
009. [04] 09014-00790 VALVE SUB-ASSY, IN MM501046
010. [04] 09015-02110 ELEMENT SUB-ASSY, MM501178
011. [04] 09016-10210 SLEEVE, PLUNGER CO MM500229
012. [04] 09016-30082 SEAT, SPRING, UPR MM501098
013. [04] 09016-40170 SPRING, PUMP PLUNG MM500360
014. [04] 09017-00170 TAPPET SUB-ASSY,IN MM500230
015. [04] 09018-30050 PIN, INJECTION PUM MM500231
016. [01] 09021-00440 RACK ASSY, CONTROL MM501255
017. [04] 09030-10060 SEAT, SPRING, LWR MM500316
018. [02] 09046-70030 PLATE MM500232
019. [ C] 09031-10310 PLATE, TAPPET ADJU MM501365
019. [ C] 09031-10300 PLATE, TAPPET ADJU MM501364
019. [ C] 09031-10280 PLATE, TAPPET ADJU MM501246
019. [ C] 09031-10170 PLATE, TAPPET ADJU P760-15160
019. [ C] 09031-10160 PLATE, TAPPET ADJU MM500314
019. [ C] 09031-10140 PLATE, TAPPET ADJU MM500312
019. [ C] 09031-10130 PLATE, TAPPET ADJU MM500311
019. [ C] 09031-10120 PLATE, TAPPET ADJU MM500310
019. [ C] 09031-10110 PLATE, TAPPET ADJU MM500309
019. [ C] 09031-10010 PLATE, TAPPET ADJU ME702559
020. [02] 09022-20080 WASHER, FUEL PIPE ME702235
021. [02] 09024-40150 SCREW, AIR BLEEDER
022. [01] 94918-00510 SCREW, HOLLOW MM500446
023. [03] 09007-00012 PLATE ASSY, ADJUST MM501077
023. [03] 09006-80020 PLATE, ADJUSTING MM514109
024. [01] 94904-71980 BOLT, W/WASHER MM501244
024. [01] 94904-80800 BOLT, WASHER HEAD
025. [01] 09055-40300 SPRING, DIAPHRAGM MM501256
026. [01] 09055-40160 SPRING, DIAPHRAGM MM501073
027. [04] 90802-20150 O-RING MM500438
028. [01] 94901-13010 WASHER, STEEL PLAT MM500928
029. [01] 90400-16101 PIN, SPLIT MM500431
030. [01] 09089-40010 E-RING ME702112
031. [ C] 09021-92540 STOPPER MM501275
031. [ C] 09021-92530 STOPPER MM501260
031. [ C] 09021-92520 STOPPER MM501259
031. [ C] 09021-92510 STOPPER MM501258
031. [ C] 09021-92500 STOPPER MM501257
032. [ C] 09021-92810 STOPPER
032. [ C] 09021-92800 STOPPER
032. [ C] 09021-92790 STOPPER
032. [ C] 09021-92780 STOPPER
032. [ C] 09021-92770 STOPPER
032. [ C] 09021-92760 STOPPER
032. [ C] 09021-92750 STOPPER
032. [ C] 09021-92740 STOPPER
032. [ C] 09021-92730 STOPPER
032. [ C] 09021-92720 STOPPER
032. [ C] 09021-92710 STOPPER
032. [ C] 09021-92700 STOPPER
032. [ C] 09021-92690 STOPPER
032. [ C] 09021-92820 STOPPER

Include in #3:

09450-02120 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09450-02120  MM409260  PUMP ASSY, INJECTI
MM409260    MITSUBISHI PUMP ASSY, INJECTI




Information:

Start By:a. remove vibration damper
The crankshaft front seal and wear sleeve come as a set and must be installed as a set. If a replacement of the seal is to be made, a replacement of the wear sleeve must also be made.
1. Make at least three holes in seal (1) with a hammer and a sharp punch.2. Use Tool (A) to remove seal (1). 3. Install Tool (C) in the seal bore.4. Install Tool (B) between Tool (C) and wear sleeve (2). Turn Tool (B) until the Tool makes a dent (crease) in wear sleeve (2). Do this in three or more places until the wear sleeve is loose.5. Remove Tools (B) and (C), and remove wear sleeve (2) from the crankshaft.Install Crankshaft Front Seal & Wear Sleeve
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, Form No. SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
1. Install the front crankshaft seal and wear sleeve with Tool (A). Use the procedures with follows:a. Clean and make a preparation of the wear sleeve inside diameter and crankshaft outside diameter with 6V1541 Quick Cure Primer. Make an application of 9S3265 Retaining Compound to the crankshaft outside diameter before the wear sleeve is installed on the crankshaft. Do not let any 6V1541 Quick Cure Primer or 9S3265 Retaining Compound get on the lip of the seal.b. Install locator (3) and bolts (4) on the crankshaft.c. Seal (1) and wear sleeve (2) must be installed dry.
Make sure the seal is installed with the part number and the arrows showing crankshaft rotation toward the outside.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the front seal group for an engine is different from the rear seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
d. Put wear sleeve (2) and seal (1) as a unit in position on locator (3).e. Put installer (5) in position on locator (3).f. Put clean engine oil on the face of nut (6) and its contact area on installer (5). Install nut (6) on locator (3).g. Tighten nut (6) until the inside surface of installer (5) comes in contact with locator (3).h. Remove Tool (D) from the crankshaft seal and wear sleeve. Tool (D) will install the seal and wear sleeve to the correct depth on the crankshaft.End By:a. install vibration damper

Have questions with 09450-02120?





09450-02040 PUMP ASSY, INJECTI 09450-02030 09450-02020 09450-02010 09450-02000
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09450-02120

Back to top