Information pump assy, fuel fe
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
IMIFAFTAbT Oil pump assembly ND094200-0320 094200-0320 Fits for HP0 Fuel Injection Pump ND0942000320 0942000320
IMIFAFTAbT Product Name: ND094200-0320 094200-0320 ND0942000320 0942000320 Oil pump assembly || Part number: ND094200-0320 094200-0320 ND0942000320 0942000320 || Fits for HP0 Fuel Injection Pump || 1 PCS Oil pump assembly || Note: Please confirm that the product shown in the part number is what you need. If you cannot confirm you can leave us a message and provide your engine serial number and nameplate
IMIFAFTAbT Product Name: ND094200-0320 094200-0320 ND0942000320 0942000320 Oil pump assembly || Part number: ND094200-0320 094200-0320 ND0942000320 0942000320 || Fits for HP0 Fuel Injection Pump || 1 PCS Oil pump assembly || Note: Please confirm that the product shown in the part number is what you need. If you cannot confirm you can leave us a message and provide your engine serial number and nameplate
Scheme ###:
| 000. | [01] | 09420-00320 | PUMP ASSY, FUEL FE | |
| 001. | [01] | 09421-00120 | HOUSING SUB-ASSY, | |
| 002. | [01] | 09423-10060 | CASING, FEED PUMP | |
| 003. | [01] | 09423-00050 | PUMP SUB-ASSY, FUE | |
| 004. | [01] | 09424-10040 | PLATE, FEED PUMP S | |
| 005. | [01] | 09424-40040 | PLATE, FEED PUMP S | |
| 006. | [01] | 09425-10050 | COVER, FEED PUMP | |
| 007. | [04] | 09408-20040 | SCREW, SUPPLY PUMP | |
| 008. | [01] | 09408-60200 | O-RING, SUPPLY PUM | |
| 009. | [01] | 09408-70050 | SEAL, SUPPLY PUMP | |
| 010. | [01] | 09420-50060 | KEY | |
| 011. | [02] | 09212-40010 | SPRING, FEED PUMP | S2256-21020-A |
| 012. | [02] | 09212-10011 | VALVE, FEED PUMP C | S2256-31041-A |
| 013. | [01] | 09212-60010 | PLUG, FEED PUMP CH | S2284-51350-A |
| 014. | [01] | 09213-00510 | PUMP SUB-ASSY, PRI | |
| 014-001. | [01] | 09211-70180 | CONNECTOR | |
| 014-002. | [01] | 09212-50010 | GASKET, CHECK VALV | S2284-71680-A |
| 014-003. | [01] | 09213-00360 | PUMP SUB-ASSY, PRI | S2250-91370-A |
| 015. | [03] | 09212-50010 | GASKET, CHECK VALV | S2284-71680-A |
| 016. | [02] | 09031-70060 | PLUG, SCREW | S2284-51060-A |
| 017. | [02] | 94901-81500 | WASHER, COPPER PLA | S2284-71120-A |
| 018. | [04] | 94904-43320 | BOLT | S2281-52070-A |
| 019. | [04] | 94901-02490 | WASHER | S2287-71100-A |
| 020. | [01] | 94918-00310 | SCREW, HOLLOW | S2283-51310-A |
| 022. | [01] | 09222-00040 | FILTER, FEED PUMP | S2257-41040-A |
| 023. | [01] | 09222-30070 | SCREW, FUEL PIPE H | S2283-51370-A |
| 024. | [01] | 09216-00020 | HOLDER SUB-ASSY, V | S2281-52600-A |
Include in #3:
09400-00430
as PUMP ASSY, FUEL FE
09420-00320
Cross reference number
| Part num | Firm num | Firm | Name |
| 09420-00320 | PUMP ASSY, FUEL FE |
Information:
1. Attach lifting strap to engine compartment cover. Remove two cotter pins and washers (1), remove four bolts (2). Lift off cover. 2. Loosen hose clamps (3) and (4) and remove hose (5). Remove three bolts (6) and remove ether aid cover (7). 3. Disconnect ether aid line (8), electrical connector (9), and loosen eight 1/4 turn fasteners (10). Remove heat shields (11) and (12). 4. Mark and disconnect starter wires (13) and ground strap (14). 5. Mark and disconnect alternator wires (15) and (16), temperature sending unit wire (17), cable mounting bracket (18), and electrical connector (19). Disconnect and remove flexible exhaust pipe (20). Disconnect two heater hoses (21). 6. Disconnect throttle linkage (22), remove two bolts (23). Set throttle linkage mounting bracket aside. Shut off and disconnect two fuel lines (24). 7. Disconnect throttle cable clip (25). Disconnect electrical wire (26), electrical connector (27) and governor wiring (28). 8. Install tool (A), lifting strap and tool (B) as shown, to support hydraulic pump. Remove twelve hydraulic pump mounting bolts (29). 9. Install lifting chains and remove four bolts and bushings (30).10. Remove engine. The following steps are to install the engine.11. Position engine in vehicle and install four bolts and bushings (30).12. Connect hydraulic pump to engine with twelve mounting bolts (29).13. Remove tooling (A) and (B), and the lifting strap that was supporting the hydraulic pump.14. Connect governor wiring (28), electrical connector (27), and wire (26). Connect throttle cable clip (25).15. Connect two fuel lines (24). Position throttle linkage mounting bracket and secure with two bolts (23). Connect throttle linkage (22).16. Connect two heater hoses (21) and flexible exhaust pipe (20). Connect alternator wires (15) and (16), temperature sending unit wire (17), cable mounting bracket (18) and electrical connector (19).17. Connect starter wires (13) and ground strap (14).18. Replace heat shields (11) and (12), fasten with eight 1/4 turn fasteners. Connect electrical connector (9) and ether aid line (8).19. Replace ether aid cover (7) and secure with three bolts (6). Replace hose (5) and connect with clamps (3) and (4).20. Attach engine compartment cover with four bolts (2) and connect cylinders with cotter pins and washers (1).End By:a. install radiator